Xianai Huang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Xianai Huang has a total of 22 co-authors. Here are the top co-authors by number of shared publications:
Ka Wing Ng
Natural Resources Canada
9 shared publicationsKun Liu
Natural Resources Canada
3 shared publicationsLouis Giroux
Natural Resources Canada, CanmetENERGY, Ottawa, Canada
3 shared publicationsTed Todoschuk
Canadian Iron & Steel Energy Research Association PO Box 20261 Grantham St. Catherines ON L2M 7W7 Canada
3 shared publicationsChristopher DiGiovanni
CanmetMATERIALS, Natural Resources Canada, Hamilton, Canada
2 shared publicationsGraeme Scott
ArcelorMittal, Global R&D Hamilton 1390 Burlington St. E. Hamilton ON L8N 3J5 Canada
2 shared publications
Latest Publications
- 24 September 2026
- Published by SAGE Publications in Ironmaking & Steelmaking: Processes, Products and Applications
Solid biocarbon suitability quantification for iron ore pellet induration
Replacement of fossil carbon reductants utilisation by carbonaceous materials from renewable sources is one of the important approaches to reduce greenhouse gas (GHG) emissions of iron and steel production. Because of the wide variation in chemical and physical properties between biogenic carbon materials, selection of suitable materials for replacing fossil carbon to achieve the goal of GHG emissions reduction while maintaining process efficiency is challenging. This study focuses on technique development for evaluating the suitability of selected solid biocarbon to replace coke breeze in iron ore pellet induration. A laboratory analytical method based on thermogravimetry analysis (TGA) was developed to assist understanding the performance of solid biocarbon in the iron ore pellet induration process. Using this technique, a wide range of biocarbon samples were examined for developing the relationship between biocarbon production and processing conditions and its performance in iron ore pellet induration. Experimental results revealed that the combustion of biocarbon initiates at lower temperature than coke, which may negatively impact the induration process as well as quality of the resultant iron ore pellet. But the combustion initiation temperature is closely related to the pyrolysis severity employed in biocarbon materials production and post-processing of biocarbon by densification. Parameters that characterise the suitability of biocarbon candidates for replacement of coke breeze in iron ore pellet induration were defined to enable direct comparison between potential biocarbon candidates. It also serves as basis for biocarbon producers to further develop their products to meet the technical needs of end-users.
- 24 September 2026
- Published by SAGE Publications in Ironmaking & Steelmaking: Processes, Products and Applications
Solid biocarbon suitability quantification for iron ore pellet induration
Replacement of fossil carbon reductants utilisation by carbonaceous materials from renewable sources is one of the important approaches to reduce greenhouse gas (GHG) emissions of iron and steel production. Because of the wide variation in chemical and physical properties between biogenic carbon materials, selection of suitable materials for replacing fossil carbon to achieve the goal of GHG emissions reduction while maintaining process efficiency is challenging. This study focuses on technique development for evaluating the suitability of selected solid biocarbon to replace coke breeze in iron ore pellet induration. A laboratory analytical method based on thermogravimetry analysis (TGA) was developed to assist understanding the performance of solid biocarbon in the iron ore pellet induration process. Using this technique, a wide range of biocarbon samples were examined for developing the relationship between biocarbon production and processing conditions and its performance in iron ore pellet induration. Experimental results revealed that the combustion of biocarbon initiates at lower temperature than coke, which may negatively impact the induration process as well as quality of the resultant iron ore pellet. But the combustion initiation temperature is closely related to the pyrolysis severity employed in biocarbon materials production and post-processing of biocarbon by densification. Parameters that characterise the suitability of biocarbon candidates for replacement of coke breeze in iron ore pellet induration were defined to enable direct comparison between potential biocarbon candidates. It also serves as basis for biocarbon producers to further develop their products to meet the technical needs of end-users.
- Open Access
- 13 November 2025
- Published by Springer Nature in Journal of Sustainable Metallurgy
- Vol. 12 (1) , 968
Correction: Coating of Biocarbon to Reduce Reactivity for Slag Foaming Applications in Electric Arc Furnace Steelmaking
- 13 November 2025
- Published by Springer Nature in Journal of Sustainable Metallurgy
- Vol. 12 (1) , 968
Open AccessCorrection: Coating of Biocarbon to Reduce Reactivity for Slag Foaming Applications in Electric Arc Furnace Steelmaking
- Open Access
- 22 October 2025
- Published by Wiley in Steel Research International
- Vol. 97 (4) , 2278-2287
Biocarbon Suitability Evaluation for Direct Injection in Blast Furnace Ironmaking
This study evaluates the feasibility of substituting pulverized coal with solid biocarbon for direct injection in blast furnace ironmaking, aiming to reduce greenhouse gas (GHG) emissions. A commercial biocarbon sample is systematically assessed for its physical, chemical, and grindability characteristics across varying substitution levels. Combustion performance is quantified using the CanmetENERGY‐Ottawa injection rig, revealing that biocarbon incorporation enhances injectant burnout. Analysis of combustion residues indicate favorable reactivity and carbon structure, supporting its suitability for blast furnace conditions. Heat and mass balance modeling further demonstrates that up to 27% GHG emission reduction can be achieved without compromising furnace operation, confirming biocarbon's potential as a viable low‐carbon alternative in ironmaking.
- 22 October 2025
- Published by Wiley in Steel Research International
- Vol. 97 (4) , 2278-2287
Open AccessBiocarbon Suitability Evaluation for Direct Injection in Blast Furnace Ironmaking
This study evaluates the feasibility of substituting pulverized coal with solid biocarbon for direct injection in blast furnace ironmaking, aiming to reduce greenhouse gas (GHG) emissions. A commercial biocarbon sample is systematically assessed for its physical, chemical, and grindability characteristics across varying substitution levels. Combustion performance is quantified using the CanmetENERGY‐Ottawa injection rig, revealing that biocarbon incorporation enhances injectant burnout. Analysis of combustion residues indicate favorable reactivity and carbon structure, supporting its suitability for blast furnace conditions. Heat and mass balance modeling further demonstrates that up to 27% GHG emission reduction can be achieved without compromising furnace operation, confirming biocarbon's potential as a viable low‐carbon alternative in ironmaking.
- Open Access
- 10 October 2025
- Published by Springer Nature in Journal of Sustainable Metallurgy
- Vol. 12 (2) , 1082-1097
Coating of Biocarbon to Reduce Reactivity for Slag Foaming Applications in Electric Arc Furnace Steelmaking
As the steel industry transitions toward net-zero greenhouse gas emissions, biocarbon emerges as a promising renewable alternative to replace fossil carbon for slag foaming in electric arc furnace (EAF) steelmaking. However, the high porosity and reactivity of biocarbon leads to technical challenges associated with injection of biocarbon and foam stability, which reduces process energy efficiency. This study investigates a novel approach to address the technical challenges by enhancing biocarbon performance in slag foaming. The enhancement is achieved by coating solid biocarbon particle with bio-oil followed by heat treatment to reduce particle porosity and reactivity. Petcoke, uncoated biocarbon, and bio-oil-coated biocarbon were systematically characterized to evaluate their physicochemical properties, reactivity profiles, and interaction with synthetic slag. Particle morphology analysis revealed that coating reduced biocarbon porosity and increased biocarbon surface roughness. Thermogravimetric analysis (TGA) experiments confirmed that coating moderated biocarbon reactivity with air and CO₂, and slag. Interaction tests with slag revealed that coated biocarbon exhibited intermediate behavior, although still more reactive than petcoke but much less reactive than uncoated biocarbon, facilitating more stable and prolonged slag foaming. Coated biocarbon can possibly generate sustained foamy slag with improved duration compared to uncoated biocarbon, while still achieving comparable foaming height. These findings highlight the potential of coated biocarbon overcome the technical barrier of biocarbon utilization and serve as a feasible, low carbon-intensive injection material for EAF steelmaking process. Graphical Abstract
- 10 October 2025
- Published by Springer Nature in Journal of Sustainable Metallurgy
- Vol. 12 (2) , 1082-1097
Open AccessCoating of Biocarbon to Reduce Reactivity for Slag Foaming Applications in Electric Arc Furnace Steelmaking
As the steel industry transitions toward net-zero greenhouse gas emissions, biocarbon emerges as a promising renewable alternative to replace fossil carbon for slag foaming in electric arc furnace (EAF) steelmaking. However, the high porosity and reactivity of biocarbon leads to technical challenges associated with injection of biocarbon and foam stability, which reduces process energy efficiency. This study investigates a novel approach to address the technical challenges by enhancing biocarbon performance in slag foaming. The enhancement is achieved by coating solid biocarbon particle with bio-oil followed by heat treatment to reduce particle porosity and reactivity. Petcoke, uncoated biocarbon, and bio-oil-coated biocarbon were systematically characterized to evaluate their physicochemical properties, reactivity profiles, and interaction with synthetic slag. Particle morphology analysis revealed that coating reduced biocarbon porosity and increased biocarbon surface roughness. Thermogravimetric analysis (TGA) experiments confirmed that coating moderated biocarbon reactivity with air and CO₂, and slag. Interaction tests with slag revealed that coated biocarbon exhibited intermediate behavior, although still more reactive than petcoke but much less reactive than uncoated biocarbon, facilitating more stable and prolonged slag foaming. Coated biocarbon can possibly generate sustained foamy slag with improved duration compared to uncoated biocarbon, while still achieving comparable foaming height. These findings highlight the potential of coated biocarbon overcome the technical barrier of biocarbon utilization and serve as a feasible, low carbon-intensive injection material for EAF steelmaking process. Graphical Abstract
- 23 July 2024
- Published by SAGE Publications in Ironmaking & Steelmaking: Processes, Products and Applications
Solid carbonaceous materials transformation during pulverised coal and natural gas co-injection
Co-injection of coal and gaseous fuel, such as natural gas (NG), is common practice promoting pulverised coal gasification in blast furnace (BF) ironmaking. The high hydrogen content in NG makes it possible to act as cleaner reductant to reduce iron ore to produce hot metal, which will result in reduced CO2 emissions during the ironmaking process. In this work, selected parameters affecting the overall performance of the pulverised coal and natural gas co-injection system were studied using the CanmetENERGY injection test rig, including coal injection rate, natural gas rate and blast oxygen enrichment. Increase in combustion intensity promotes conversion of injected coal into solid carbonaceous material with relatively low reactivity with CO2. Hence, it reduces the competitiveness of combustion residues for oxygen in the raceway to continue the gasification process. NG co-injection reduces the coal combustion intensity but enhances the reactivity of combustion residues by competing the oxygen in the raceway.
- 23 July 2024
- Published by SAGE Publications in Ironmaking & Steelmaking: Processes, Products and Applications
Solid carbonaceous materials transformation during pulverised coal and natural gas co-injection
Co-injection of coal and gaseous fuel, such as natural gas (NG), is common practice promoting pulverised coal gasification in blast furnace (BF) ironmaking. The high hydrogen content in NG makes it possible to act as cleaner reductant to reduce iron ore to produce hot metal, which will result in reduced CO2 emissions during the ironmaking process. In this work, selected parameters affecting the overall performance of the pulverised coal and natural gas co-injection system were studied using the CanmetENERGY injection test rig, including coal injection rate, natural gas rate and blast oxygen enrichment. Increase in combustion intensity promotes conversion of injected coal into solid carbonaceous material with relatively low reactivity with CO2. Hence, it reduces the competitiveness of combustion residues for oxygen in the raceway to continue the gasification process. NG co-injection reduces the coal combustion intensity but enhances the reactivity of combustion residues by competing the oxygen in the raceway.
- Open Access
Ranking of Injection Biochar for Slag Foaming Applications in Steelmaking
The electric arc furnace (EAF) has the potential to significantly contribute to the decarbonization of the iron and steel industry. However, during EAF steelmaking, carbon still needs to be injected into the molten slag to initiate slag foaming, which is beneficial to the energy efficiency and protection of the furnace. To move away from fossil carbon, biocarbon has gained attention as an injection carbon agent. In this study, two biochar candidates were added to the molten slag layer of an induction furnace for steel melting, to simulate EAF steelmaking conditions. The resultant slag foaming height was measured, and a ranking in comparison to two fossil carbon candidates was developed. The results indicate that the injection biochar sample, in the form of a bio-briquette, has a considerable degree of slag foaming capacity. More work is ongoing to develop a standardized testing methodology of ranking various injection biochar candidates for their suitability and qualification for use on a larger scale.
Open AccessRanking of Injection Biochar for Slag Foaming Applications in Steelmaking
The electric arc furnace (EAF) has the potential to significantly contribute to the decarbonization of the iron and steel industry. However, during EAF steelmaking, carbon still needs to be injected into the molten slag to initiate slag foaming, which is beneficial to the energy efficiency and protection of the furnace. To move away from fossil carbon, biocarbon has gained attention as an injection carbon agent. In this study, two biochar candidates were added to the molten slag layer of an induction furnace for steel melting, to simulate EAF steelmaking conditions. The resultant slag foaming height was measured, and a ranking in comparison to two fossil carbon candidates was developed. The results indicate that the injection biochar sample, in the form of a bio-briquette, has a considerable degree of slag foaming capacity. More work is ongoing to develop a standardized testing methodology of ranking various injection biochar candidates for their suitability and qualification for use on a larger scale.
- 16 February 2023
- Published by Taylor & Francis in International Journal of Coal Preparation and Utilization
- Vol. 44 (2) , 189-201
Coal rheology – the effect of coal origin, rank, and particle size
Coal rheology is a critical parameter for determining the coking and caking ability of metallurgical coals for cokemaking. The effect of rank, hardness differences due to rank, and particle size on the resultant fluidity and dilatation results were demonstrated for various rank Applachian coals in previous studies. Particles less than USA Standard screen size No. 140 had poorer rheology responses compared to other size fractions. For the third phase of this study, the effect of particle size and rank of Western Canadian coals were also evaluated. All samples and rheology parameters were determined prepared using the standard ASTM methods. In addition, rheology was also measured on sized subsets to determine the effect of particle size and rank on the overall rheology results but from a different geological era compared to Applachian coals. Particle size limits for the Gieseler and Dilatometer tests are suggested. The importance of using temperature range is also emphasized.
- 16 February 2023
- Published by Taylor & Francis in International Journal of Coal Preparation and Utilization
- Vol. 44 (2) , 189-201
Coal rheology – the effect of coal origin, rank, and particle size
Coal rheology is a critical parameter for determining the coking and caking ability of metallurgical coals for cokemaking. The effect of rank, hardness differences due to rank, and particle size on the resultant fluidity and dilatation results were demonstrated for various rank Applachian coals in previous studies. Particles less than USA Standard screen size No. 140 had poorer rheology responses compared to other size fractions. For the third phase of this study, the effect of particle size and rank of Western Canadian coals were also evaluated. All samples and rheology parameters were determined prepared using the standard ASTM methods. In addition, rheology was also measured on sized subsets to determine the effect of particle size and rank on the overall rheology results but from a different geological era compared to Applachian coals. Particle size limits for the Gieseler and Dilatometer tests are suggested. The importance of using temperature range is also emphasized.
- Open Access
Interaction Behavior of Biogenic Material with Electric Arc Furnace Slag
Electric arc furnaces (EAFs) are used for steel production, particularly when recycling scrap material. In EAFs, carbonaceous material is charged with other raw materials or injected into molten slag to generate foam on top of liquid metal to increase energy efficiency. However, the consumption of fossil carbon leads to greenhouse gas emissions (GHGs). To reduce net GHG emissions from EAF steelmaking, the substitution of fossil carbon with sustainable biogenic carbon can be applied. This study explores the possibility of the substitution of fossil material with biogenic material produced by different pyrolysis methods and from various raw materials in EAF steelmaking processes. Experimental work was performed to study the effect of biogenic material utilization on steel and slag composition using an induction melting furnace with 50 kg of steel capacity. The interaction of biogenic material derived from different raw materials and pyrolysis processes with molten synthetic slag was also investigated using a tensiometer. Relative to other biogenic materials tested, a composite produced with densified softwood had higher intensity interfacial reactions with slag, which may be attributed to the rougher surface morphology of the densified biogenic material.
Open AccessInteraction Behavior of Biogenic Material with Electric Arc Furnace Slag
Electric arc furnaces (EAFs) are used for steel production, particularly when recycling scrap material. In EAFs, carbonaceous material is charged with other raw materials or injected into molten slag to generate foam on top of liquid metal to increase energy efficiency. However, the consumption of fossil carbon leads to greenhouse gas emissions (GHGs). To reduce net GHG emissions from EAF steelmaking, the substitution of fossil carbon with sustainable biogenic carbon can be applied. This study explores the possibility of the substitution of fossil material with biogenic material produced by different pyrolysis methods and from various raw materials in EAF steelmaking processes. Experimental work was performed to study the effect of biogenic material utilization on steel and slag composition using an induction melting furnace with 50 kg of steel capacity. The interaction of biogenic material derived from different raw materials and pyrolysis processes with molten synthetic slag was also investigated using a tensiometer. Relative to other biogenic materials tested, a composite produced with densified softwood had higher intensity interfacial reactions with slag, which may be attributed to the rougher surface morphology of the densified biogenic material.
- 19 April 2020
- Published by Taylor & Francis in International Journal of Coal Preparation and Utilization
- Vol. 42 (6) , 1651-1663
Grindability of biocarbon and coal blends in rolling mill
Partial substitution of pulverized coal (PCI) by renewable biocarbon for blast furnace injection is a practical approach to reduce GHGs in the steel production sector. For using biocarbon as feedstock, it is critical to measure its grindability to understand its milling behavior compared to that of typical PCI coal, and thus help decide on adjusting grinding process of existing equipment or selecting appropriate milling equipment. From the significant differences in chemical and physical properties of biocarbon and PCI coal, grinding capacity variations are also expected. In addition, as the pyrolysis process modifies the chemical and physical properties of biomass, this could affect the efficiency of co-milling with coal and therefore co-injection in blast furnace ironmaking. The increase in milling capacity in turn would enable a reduction in the amount of coal used without the requirement for supplementary grinding facility. This paper presents an experimental investigation of the co-grinding behavior of coal and biocarbon produced by pyrolysis of woody biomass from two different conditions and post-processes. The main aim of this study was to identify or develop a method of grindability determination for coal, biocarbon blend, which would allow direct comparison between coal, biocarbon, and coal-biocarbon blends in terms of their grinding capacity. The study also includes the assessment of the possibility of adapting the existing coal and biomass grindability determination method for the evaluation of coalbiocarbon co-milling. The laboratory tests used focused on the influence of initial sample fixed mass and volume, composition of coal and biocarbon, the pyrolysis severity of biocarbon, and the densification process of biocarbon. The grinding behavior of biocarbon-coal mixtures determined by ASTM HGI procedure for coal is presented and compared in this paper. The findings show that milling tests conducted with fixed sample mass and fixed sample volume on same coal-biocarbon blend sample produce different and unrelated results. Moreover, grinding test results with fixed initial sample volume does not reflect material behavior in industrial grinding facilities. Therefore, it is suggested that the ASTM HGI method should be strictly followed to generate comparable grindability data for coal, biocarbon, and coal-biocarbon mixtures.
- 19 April 2020
- Published by Taylor & Francis in International Journal of Coal Preparation and Utilization
- Vol. 42 (6) , 1651-1663
Grindability of biocarbon and coal blends in rolling mill
Partial substitution of pulverized coal (PCI) by renewable biocarbon for blast furnace injection is a practical approach to reduce GHGs in the steel production sector. For using biocarbon as feedstock, it is critical to measure its grindability to understand its milling behavior compared to that of typical PCI coal, and thus help decide on adjusting grinding process of existing equipment or selecting appropriate milling equipment. From the significant differences in chemical and physical properties of biocarbon and PCI coal, grinding capacity variations are also expected. In addition, as the pyrolysis process modifies the chemical and physical properties of biomass, this could affect the efficiency of co-milling with coal and therefore co-injection in blast furnace ironmaking. The increase in milling capacity in turn would enable a reduction in the amount of coal used without the requirement for supplementary grinding facility. This paper presents an experimental investigation of the co-grinding behavior of coal and biocarbon produced by pyrolysis of woody biomass from two different conditions and post-processes. The main aim of this study was to identify or develop a method of grindability determination for coal, biocarbon blend, which would allow direct comparison between coal, biocarbon, and coal-biocarbon blends in terms of their grinding capacity. The study also includes the assessment of the possibility of adapting the existing coal and biomass grindability determination method for the evaluation of coalbiocarbon co-milling. The laboratory tests used focused on the influence of initial sample fixed mass and volume, composition of coal and biocarbon, the pyrolysis severity of biocarbon, and the densification process of biocarbon. The grinding behavior of biocarbon-coal mixtures determined by ASTM HGI procedure for coal is presented and compared in this paper. The findings show that milling tests conducted with fixed sample mass and fixed sample volume on same coal-biocarbon blend sample produce different and unrelated results. Moreover, grinding test results with fixed initial sample volume does not reflect material behavior in industrial grinding facilities. Therefore, it is suggested that the ASTM HGI method should be strictly followed to generate comparable grindability data for coal, biocarbon, and coal-biocarbon mixtures.
- 9 April 2019
- Published by Springer Nature in Metallurgical and Materials Transactions B
- Vol. 50 (3) , 1387-1398
Carbonaceous Material Properties and Their Interactions with Slag During Electric Arc Furnace Steelmaking
- 9 April 2019
- Published by Springer Nature in Metallurgical and Materials Transactions B
- Vol. 50 (3) , 1387-1398
Carbonaceous Material Properties and Their Interactions with Slag During Electric Arc Furnace Steelmaking