Jianwen Liu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Jianwen Liu has a total of 31 co-authors. Here are the top co-authors by number of shared publications:
- Yuman Zhu
Monash Centre for Additive Manufacturing, Monash University, Melbourne, VIC, Australia.
4 shared publications Aijun Huang
3 shared publicationsKai Zhang
2 shared publications- Kai Zhang
School of Materials and Chemistry, University of Shanghai for Science and Technology, Shanghai 200093, China
2 shared publications Yi Yang
2 shared publications- Aijun Huang
Monash Centre of Additive Manufacturing, Monash University, Notting Hill, Australia
1 shared publication
Latest Publications
- Open Access
- 12 August 2026
- Published by Elsevier in SSRN Electronic Journal
Effect of Martensitic Phase Constitution on Residual Stress Development in Ti-6Al-4V and Ti-6Al-2Sn-4Zr-6Mo: A Neutron Diffraction Study
Additively manufactured titanium alloys in the as-built condition frequently develop substantial residual stresses due to steep thermal gradients and constrained thermal contraction during processing. These stresses can induce distortion, baseplate deflection, and interfacial delamination, thereby limiting dimensional stability and structural integrity. In this study, the role of martensitic phase constitution on residual stress evolution in Ti–6Al–4V and Ti–6Al–2Sn–4Zr–6Mo thin-wall specimens fabricated under identical laser powder bed fusion processing conditions is systematically investigated. Macroscopic residual stresses were quantified using neutron diffraction–based strain mapping, and the resulting baseplate deflection was measured using optical profilometry. The results revealed pronounced tensile longitudinal and normal stresses concentrated along the Ti64 wall edges, leading to measurable baseplate deflection. In contrast, Ti6246 walls displayed significantly reduced tensile stresses, with compressive normal stresses developing near the wall-baseplate interface. This attenuated stress state corresponds to negligible baseplate distortion. The contrasting behavior is attributed to the β to α″ transformation in Ti6246, where the associated volumetric expansion enhances strain accommodation and suppresses tensile stress accumulation. These findings demonstrate that martensitic phase constitution plays a critical role in governing residual stress evolution in LPBF-processed titanium alloys and establish Ti6246 as a promising alternative to Ti64 for applications requiring improved dimensional stability.
- 12 August 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessEffect of Martensitic Phase Constitution on Residual Stress Development in Ti-6Al-4V and Ti-6Al-2Sn-4Zr-6Mo: A Neutron Diffraction Study
Additively manufactured titanium alloys in the as-built condition frequently develop substantial residual stresses due to steep thermal gradients and constrained thermal contraction during processing. These stresses can induce distortion, baseplate deflection, and interfacial delamination, thereby limiting dimensional stability and structural integrity. In this study, the role of martensitic phase constitution on residual stress evolution in Ti–6Al–4V and Ti–6Al–2Sn–4Zr–6Mo thin-wall specimens fabricated under identical laser powder bed fusion processing conditions is systematically investigated. Macroscopic residual stresses were quantified using neutron diffraction–based strain mapping, and the resulting baseplate deflection was measured using optical profilometry. The results revealed pronounced tensile longitudinal and normal stresses concentrated along the Ti64 wall edges, leading to measurable baseplate deflection. In contrast, Ti6246 walls displayed significantly reduced tensile stresses, with compressive normal stresses developing near the wall-baseplate interface. This attenuated stress state corresponds to negligible baseplate distortion. The contrasting behavior is attributed to the β to α″ transformation in Ti6246, where the associated volumetric expansion enhances strain accommodation and suppresses tensile stress accumulation. These findings demonstrate that martensitic phase constitution plays a critical role in governing residual stress evolution in LPBF-processed titanium alloys and establish Ti6246 as a promising alternative to Ti64 for applications requiring improved dimensional stability.
- Open Access
- 25 October 2025
- Published by Elsevier in Materials Science and Engineering: R: Reports
- Vol. 167
Fatigue and damage tolerance performance of additively-manufactured titanium alloys for structural application: A comprehensive review
- 25 October 2025
- Published by Elsevier in Materials Science and Engineering: R: Reports
- Vol. 167
Open AccessFatigue and damage tolerance performance of additively-manufactured titanium alloys for structural application: A comprehensive review
- Open Access
- 1 March 2024
- Published by Elsevier in Additive Manufacturing Frontiers
- Vol. 3 (1)
Improved Ductility by Reducing Powder Size in Laser Powder Bed Fusion of AlSi10Mg
- 1 March 2024
- Published by Elsevier in Additive Manufacturing Frontiers
- Vol. 3 (1)
Open AccessImproved Ductility by Reducing Powder Size in Laser Powder Bed Fusion of AlSi10Mg
- Open Access
- 1 February 2024
- Published by AIP Publishing in AIP Advances
- Vol. 14 (2)
Effect of processing parameters on the defects, microstructure, and property evaluation of Ti-6Al-4V titanium alloy processed by laser powder bed fusion
In this study, we designed the processing windows for laser powder bed fusion (LPBF) of Ti-6Al-4V (Ti-64) alloy by using central composite design and made a detailed investigation into the influence of processing parameters on the defects. The purpose is to investigate the effect of defects on mechanical properties. It was found that insufficient energy density could lead to the formation of lack of fusion (LOF) defects and produce non-melted powders on the surface, while excessive energy density could lead to cracks that were detrimental to mechanical performance. In addition, the microstructural evaluation found that relatively low energy density could lead to shorter columnar prior-β grains, while prior-β grains in the sample processed by the high energy density extended almost the entire height of the cross-section, which could lead to the strong mechanical property anisotropy. The prior β grains are formed by heterogeneous nucleation on the partially melted material powder. As the energy input increases, all the powder powders in the molten pool can be melted so that these particles do not act as nucleation sites and the prior β grain can grow through more layers without forming new grains being able to nucleate. The prior β-grain in as-built Ti-64 samples consisted of acicular α’ martensite with myriads of lattice distortions, as a precursor to a phase transition, which lead to strong tensile strength and poor ductility. Annealing heat treatment promoted the improvement of the ductile performance of LPBF Ti-64. Overall, this study provides comprehensive views on the effects of processing parameters (laser power, scanning speed, and hatch distance) on the internal (pores and LOF) and external (unmelted powder, sintering neck, and crack), defects, microstructure, and tensile property evaluation of LPBF Ti-64, which offer insights for the development of additive manufactured titanium alloys with excellent mechanical property.
- 1 February 2024
- Published by AIP Publishing in AIP Advances
- Vol. 14 (2)
Open AccessEffect of processing parameters on the defects, microstructure, and property evaluation of Ti-6Al-4V titanium alloy processed by laser powder bed fusion
In this study, we designed the processing windows for laser powder bed fusion (LPBF) of Ti-6Al-4V (Ti-64) alloy by using central composite design and made a detailed investigation into the influence of processing parameters on the defects. The purpose is to investigate the effect of defects on mechanical properties. It was found that insufficient energy density could lead to the formation of lack of fusion (LOF) defects and produce non-melted powders on the surface, while excessive energy density could lead to cracks that were detrimental to mechanical performance. In addition, the microstructural evaluation found that relatively low energy density could lead to shorter columnar prior-β grains, while prior-β grains in the sample processed by the high energy density extended almost the entire height of the cross-section, which could lead to the strong mechanical property anisotropy. The prior β grains are formed by heterogeneous nucleation on the partially melted material powder. As the energy input increases, all the powder powders in the molten pool can be melted so that these particles do not act as nucleation sites and the prior β grain can grow through more layers without forming new grains being able to nucleate. The prior β-grain in as-built Ti-64 samples consisted of acicular α’ martensite with myriads of lattice distortions, as a precursor to a phase transition, which lead to strong tensile strength and poor ductility. Annealing heat treatment promoted the improvement of the ductile performance of LPBF Ti-64. Overall, this study provides comprehensive views on the effects of processing parameters (laser power, scanning speed, and hatch distance) on the internal (pores and LOF) and external (unmelted powder, sintering neck, and crack), defects, microstructure, and tensile property evaluation of LPBF Ti-64, which offer insights for the development of additive manufactured titanium alloys with excellent mechanical property.
- 17 December 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Partial State Feedback Based Adaptive Control for Lateral Vehicle Motion with Sensor Failures
This paper presents an adaptive partial state feedback scheme for desired sensor failure compensation in the lateral vehicle motion. Consider that the sensor failure greatly deteriorates the instructions of the autopilot and blurs the driver’s judgement, leading to the safety accident of the vehicle. To handle these perils, the observer is used to estimate unmeasurable state information since the sensor failure exists. The nominal partial state feedback controller is designed and parameterized when the system model analysed is known. In addition, the adaptive compensation method is used to obtain a controller structure to deal with the unknown system parameters, which can effectively solve the problem of unknown system models caused by parameter perturbations. Finally, the effectiveness of the fault compensation scheme is verified by simulation results.
- 17 December 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Partial State Feedback Based Adaptive Control for Lateral Vehicle Motion with Sensor Failures
This paper presents an adaptive partial state feedback scheme for desired sensor failure compensation in the lateral vehicle motion. Consider that the sensor failure greatly deteriorates the instructions of the autopilot and blurs the driver’s judgement, leading to the safety accident of the vehicle. To handle these perils, the observer is used to estimate unmeasurable state information since the sensor failure exists. The nominal partial state feedback controller is designed and parameterized when the system model analysed is known. In addition, the adaptive compensation method is used to obtain a controller structure to deal with the unknown system parameters, which can effectively solve the problem of unknown system models caused by parameter perturbations. Finally, the effectiveness of the fault compensation scheme is verified by simulation results.