Xinhua Liu
Research Subjects
Xinhua Liu has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Bo Gao
School of Electrical Engineering and Automation, Harbin Institute of Technology, Harbin, China
1 shared publication - Ling Ding
School of Electrical Engineering and Automation, Harbin Institute of Technology, Harbin, China
1 shared publication - Ronghai Qu
Huazhong University of Science and Technology
1 shared publication - Shumei Cui
Harbin Institute of Technology
1 shared publication - Tianxu Zhao
School of Electrical Engineering and Automation, Harbin Institute of Technology, Harbin 150001, China
1 shared publication - Wutao Chen
State Key Laboratory of Advanced Electromagnetic Engineering and Technology, School of Electrical and Electronic Engineering, Huazhong University of Science and Technology, Wuhan, China
1 shared publication
Latest Publications
- 12 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 61 (6) , 9269-9280
Comparative Study of Hybrid PM Assisted Synchronous Reluctance Machines with Different Configurations
In this paper, the rotor topology of hybrid permanent magnet assisted synchronous reluctance machines (HPM-SynRMs) with parallel, series and parallel-series configurations is given and the analytical models are presented. Based on the analytical models, a method for determining the initial dimensions of the rotors topology is presented. In the subsequent optimization process, a comparative analysis of the torque components, cost, external characteristics, and efficiency of the three motor configurations is conducted. The selected optimal design is compared with the reference PM machine under both overload and rated conditions. The results indicate that the HPM-SynRM achieves higher torque performance under overload conditions and slightly lower torque under rated conditions compared to the reference machine, while reducing the PM cost by 34.4%. Finally, a prototype is developed to validate the simulation results.
- 12 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 61 (6) , 9269-9280
Comparative Study of Hybrid PM Assisted Synchronous Reluctance Machines with Different Configurations
In this paper, the rotor topology of hybrid permanent magnet assisted synchronous reluctance machines (HPM-SynRMs) with parallel, series and parallel-series configurations is given and the analytical models are presented. Based on the analytical models, a method for determining the initial dimensions of the rotors topology is presented. In the subsequent optimization process, a comparative analysis of the torque components, cost, external characteristics, and efficiency of the three motor configurations is conducted. The selected optimal design is compared with the reference PM machine under both overload and rated conditions. The results indicate that the HPM-SynRM achieves higher torque performance under overload conditions and slightly lower torque under rated conditions compared to the reference machine, while reducing the PM cost by 34.4%. Finally, a prototype is developed to validate the simulation results.
- 14 September 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Energy Conversion
- Vol. 39 (1) , 567-577
Optimal Design of PCB Coreless Axial Flux Permanent Magnet Synchronous Motor With Arc Windings
The coreless axial flux permanent magnet synchronous motor with printed circuit board stator (PCB motor for short) has attracted research interests for many advantages, such as flexible and precise winding design, low toque ripple, noiseless operation and simple manufacturing process. The motor performance, however, highly depends on its wiring design, which should be carefully optimized. In this article, an arc-shaped distributed winding is adopted due to its higher efficiency. The PCB motor has a 3D magnetic field distribution, which makes its optimal design very difficult since the 3D finite element analysis is usually required. In this article, an analytical model of PCB motor including 3D magnetic field, arc-shaped winding flux linkage and eddy current loss is firstly deduced. On this basis, a multi-objective optimal design is then carried out to design a PCB motor for a vacuum cleaner. Compared with the concentrated winding, the arc winding can achieve a 3% efficiency improvement. Finally, a 130 W prototype and testbench were built and the presented analytical model is verified by experiments. The results show that there is little difference between calculation and experiment. The presented method effectively simplifies the design process of this kind of motor and shortens the design time.
- 14 September 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Energy Conversion
- Vol. 39 (1) , 567-577
Optimal Design of PCB Coreless Axial Flux Permanent Magnet Synchronous Motor With Arc Windings
The coreless axial flux permanent magnet synchronous motor with printed circuit board stator (PCB motor for short) has attracted research interests for many advantages, such as flexible and precise winding design, low toque ripple, noiseless operation and simple manufacturing process. The motor performance, however, highly depends on its wiring design, which should be carefully optimized. In this article, an arc-shaped distributed winding is adopted due to its higher efficiency. The PCB motor has a 3D magnetic field distribution, which makes its optimal design very difficult since the 3D finite element analysis is usually required. In this article, an analytical model of PCB motor including 3D magnetic field, arc-shaped winding flux linkage and eddy current loss is firstly deduced. On this basis, a multi-objective optimal design is then carried out to design a PCB motor for a vacuum cleaner. Compared with the concentrated winding, the arc winding can achieve a 3% efficiency improvement. Finally, a 130 W prototype and testbench were built and the presented analytical model is verified by experiments. The results show that there is little difference between calculation and experiment. The presented method effectively simplifies the design process of this kind of motor and shortens the design time.