МММаксим Марченко

Максим Марченко

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Максим Марченко has a total of 24 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    НАУКОВЕ ОБҐРУНТУВАННЯ ТЕРМОГІДРОДИНАМІЧНИХ ПРОЦЕСІВ І ГРАНИЧНИХ ПАРАМЕТРІВ ВАКУУМУВАННЯ ПІД ЧАС ПРОЄКТУВАННЯ РОТОРНИХ УСТАНОВОК ШВИДКІСНОГО ОХОЛОДЖЕННЯ ХЛІБОБУЛОЧНИХ ВИРОБІВ МЕТОДАМИ CFD-МОДЕЛЮВАННЯ

    by Віктор Федорів, Андрій Мартинюк, Мирослав Стечишин, Максим Марченко

    The article solves an important engineering and technical problem related to accelerating the cooling process of bakery products by designing and proving the feasibility of the parameters of a new rotary vacuum unit. The need to abandon traditional convection approaches, which take as long as 180–240 minutes and lead to a noticeable weight loss (3,5–5,0%), in favor of continuous vacuum technologies has been confirmed. Scientific methods have proven that the use of a rotary design with several sections contributes to the organization of flow production, which is vital for modern large-scale enterprises. The research methodology is based on a comprehensive approach that integrates computational fluid dynamics (CFD) methods using the ANSYS Fluent software package and experimental testing on a pilot stand. A mathematical model of heat and mass transfer in the capillary-porous granular material of bread has been created, which takes into account the phase change of water and the dynamic pressure conditions at the boundary. Using numerical modeling, it was possible to establish maps of vapor velocity distribution and internal pressure gradients in the crumb. The limiting rate of vacuum creation (1,5–1,8 kPa/s) was determined, which stimulates intense evaporation of moisture without destroying the internal structure of the product. The Cross-Vacuum system concept was introduced and substantiated for the first time – an improved algorithm for step-by-step pressure equalization between rotor chambers. The logic of controlling this process based on an industrial PLC controller is described in detail, providing flexibility in adjusting cooling conditions for a wide range of products. Test results showed a reduction in cooling time to 4–6 minutes, a 2,5% reduction in moisture loss compared to convection, and 22–28% energy savings due to the recuperation effect. The article will be of considerable practical value to design engineers and technologists in the baking industry, as the proposed equipment frees up to 80% of the production space normally occupied by traditional cooling devices (coolers).

  • Digital gnss and rtk technologies in pre-design analysis of industrial and agricultural areas

    by Andrii Martyniuk, Svitlana Pidhaichuk, Viktor Fedoriv, Maksym Marchenko, Mykola Borys

    The article substantiates the methodological principles for pre-design analysis of industrial territories, using the example of a seed processing plant covering 4.92 hectares. Attention is paid to the formation of an accurate spatial framework for architectural and engineering design through the application of RTK technology based on the GNSS reference station network System.NET. The research highlights the importance of high-precision geodetic support during the initial stages of industrial facility reconstruction and modernization, where reliable spatial data underpin effective planning and engineering decision-making. The study investigates the challenges of obtaining metric data under dense industrial development, where signal shielding, multipath effects, and limited satellite visibility significantly reduce the efficiency of conventional satellite measurements. To improve the reliability and accuracy of spatial positioning, an integrated approach combining GNSS observations with electronic total station surveying was implemented. A comparative analysis of the applied measurement methods was conducted, enabling the determination of optimal surveying conditions and the minimization of positioning errors when creating source graphic materials and digital cartographic datasets. A separate emphasis is placed on the use of computer graphics tools and GIS-based modeling methods to process and interpret the results obtained. Based on field measurements, a digital terrain model was created in QGIS using triangulation techniques. Through geovisualization tools, including slope maps and hillshade models, a comprehensive analysis of surface morphology was performed. The results obtained provide a reliable basis for vertical planning, drainage assessment, functional zoning, and the optimization of industrial infrastructure placement. The scientific novelty of the research lies in optimizing pre-design analysis methods for complex industrial territories by integrating precision geodetic measurements into a unified digital graphic model of the object. The practical significance of the study lies in improving the quality of architectural and planning decisions, reducing reconstruction risks, and increasing the level of automation in preparing project documentation. Keywords: pre-design analysis, architectural design, digital terrain model, computer graphics, GNSS, RTK, QGIS, industrial territories.

  • Open Access

    ДОСЛІДЖЕННЯ КІНЕТОСТАТИЧНИХ ПАРАМЕТРІВ СИМЕТРИЧНИХ ВАЖІЛЬНИХ МЕХАНІЗМІВ З ПЕРІОДИЧНИМ ВИСТОЄМ ВИХІДНОЇ ЛАНКИ

    by В’яЧеслав Харжевський, Роман Божек, Максим Марченко, Антон Харжевський

    The paper considers the problem of determining the kinetostatic characteristics of Chebyshev linkage mechanisms, whose link length ratios provide the plotting of symmetrical curves of the coupler’s point. The upper section of the coupler’s curve of the mentioned mechanisms was used to approximate a circular arc. Such mechanisms can be used independently in mechanical engineering, providing path generating motion of a link with the “best approximation conditions” according to Chebyshev within its certain segment. These conditions include the presence of a uniform deviation from a circular arc with the maximum possible number of interpolation nodes within the approximation segment of the coupler curve. Path generating linkage mechanisms can also be used as a basis for designing mechanisms with periodic dwell of the output link, which is considered in the article. To determine the optimal geometric parameters for these mechanisms, it is essential to conduct both kinematic and kinetostatic analyses. In the presented paper, a methodology for determining the kinetostatic parameters of the dwell mechanisms is introduced, calculations according to the obtained formulae are also performed, and results are presented in the form of diagrams of maximum values of the main kinetostatic parameters of the mechanisms, such as: reactions in the kinematic pairs, instantaneous and cyclic efficiency coefficients, the force increasing coefficient, which allows to carry out the optimal synthesis of mechanisms with the dwell of the output link. Based on the obtained dependencies, a computer program was made up, which was used to study the force loads on the mechanisms’ links under dynamic loading. The values of the dynamic parameters of linkage mechanisms that were obtained can be used for preliminary strength calculations of the links and parts of the mechanisms.

  • Open Access

    МОДЕЛЮВАННЯ ГЕОМЕТРИЧНИХ ТА ЕКСПЛУАТАЦІЙНИХ ХАРАКТЕРИСТИК ОСАДЖУВАЛЬНОГО ОБЛАДНАННЯ З ВИКОРИСТАННЯМ CAD/CAE

    by Максим Марченко, В’яЧеслав Харжевський, Світлана Підгайчук, Віктор Федорів

    The paper is dedicated to the application of computational fluid dynamics (CFD) methods for modeling and analyzing technological equipment used in food processing industries for the separation of heterogeneous systems of the “liquid–liquid” and “liquid–solid” types. Such separation processes play a key role in ensuring the quality, safety, and stability of food products, as well as in improving the efficiency of technological operations. The objects of the study include cyclones, separators, and settling tanks, which are widely applied in dairy, sugar, and canning industries for purification, clarification, concentration, and phase separation of process streams. Numerical simulation of two-phase flows was carried out using a CFD environment, which made it possible to perform a detailed analysis of internal hydrodynamic processes that are difficult or impossible to investigate exclusively by experimental methods. The study focused on determining velocity and pressure fields, flow structure, trajectories of dispersed particles or droplets, and the conditions governing particle settling and phase separation. Particular attention was paid to the influence of design parameters, such as geometric characteristics of the equipment, as well as operating conditions, including flow rate and physical properties of the phases, on the efficiency of separation processes. The obtained simulation results demonstrate that CFD methods provide reliable and informative predictions of the performance of technological equipment at both the design and modernization stages. It is shown that numerical modeling enables the identification of unfavorable flow zones, assessment of separation efficiency, and evaluation of the impact of constructive and regime parameters on process outcomes. The use of CFD as a design and analysis tool allows for the optimization of equipment geometry and operating modes, a significant reduction in the scope of time-consuming and costly experimental studies, improvement of energy efficiency, and enhancement of the quality and stability of final food products. Overall, the results confirm the expediency and prosperity of integrating CFD-based approaches into the development and improvement of separation and sedimentation equipment for food processing industries. The developed technique and research results are used in the academic process for the students of engineering specialties of higher education establishments.

  • Open Access

    ДОСЛІДЖЕННЯ КОНСТРУКТИВНИХ ПАРАМЕТРІВ КАВІТАЦІЙНИХ НАСАДКІВ ТА РЕЖИМІВ РОБОТИ ОБЛАДНАННЯ ВОДОПІДГОТОВКИ ДЛЯ ТЕПЛОМЕРЕЖ У SOLIDWORKS І ПРАКТИЧНЕ ВИКОРИСТАННЯ

    by Олександр Душенко, Віталій Ткачук, Максим Марченко

    Recently, with the increase in the number of studies on the cavitation effect on liquid media, it has been shown that cavitation jets can be practically applicable in many useful technologies. In addition to the already widely used phenomenon of acceleration of chemical reactions in the preparation of emulsions and suspensions, changing the properties and composition of water, new modern technical solutions for the use of cavitation appear. The paper considers the issue of engineering analysis of technical systems by means of computer modeling, in particular, the study of the design parameters of cavitation nozzles using the SOLIDWORKS Flow Simulation engineering analysis system, which allows conducting numerical experiments to determine their characteristics, namely, to determine the cavitation effect on changing the properties and composition of water. The paper presents the capabilities of the SOLIDWORKS Flow Simulation software product to solve the scientific and technical problem of determining the cavitation characteristics of the nozzles under study. The design parameters of cavitation nozzles were studied in SOLIDWORKS Flow Simulation for flow characteristics according to the cavitation number and the maximum mixing capacity of the liquid flow was analyzed to create intensive conditions for oxidative and hydrogen reactions in real operating modes of water treatment equipment for heating networks and practical confirmation of the operability of the proposed solutions was obtained. From the obtained results of modeling the liquid flow through the nozzles, it was established that the greatest cavitation effect is exerted according to the cavitation number at an inlet pressure of 0.12 MPa. The best effect of liquid mixing at the outlet of the nozzle was obtained in the stepped nozzle at the inlet and outlet. From the point of view of manufacturing technology, the stepped nozzle at the inlet and outlet, which was used in the experimental equipment, is more technologically advanced in terms of manufacturing. Experimental equipment was manufactured with the possibility of using individual blocks, namely a hydrostatic cavitator, a magnetization block, a vibration cavitator and their use in a complex. The practical application of the impact on the composition of tap water was evaluated by changing the indicators: pH, total mineralization (indicator - TDS), oxidation-reduction potential (ORP) and analysis of the sediment that forms over time after settling (three days). The conducted studies make it possible to design equipment for water treatment for heating networks according to the required productivity of real needs.

  • Open Access

    РОЗРОБКА І УЗГОДЖЕННЯ КОМПЛЕКСНОГО ГІДРАВЛІЧНОГО ПРИВОДА З МЕХАНІЗМАМИ ПЛІСИРУВАЛЬНОЇ МАШИНИ

    by Ольга Коротич, Андрій Поліщук, Максим Марченко, Елла Золотенко, Юрій Михайловський

    В результаті проведеного аналізу конструкцій технологічних машин легкої промисловості та безпосередньо плісирувальної техніки, а також їх приводів, виявлених недоліків і переваг, авторами розроблено комплексний гідравлічний привод плісирувальної машини, який включає в себе засіб розподілу руху робочої рідини на виконавчі механізми, сполучений з насосною установкою та гідроциліндрами виконавчих механізмів. Засіб розподілу руху робочої рідини на виконавчі механізми (гідравлічний розподільник) є оригінальною конструктивною розробкою стосовно технологічного процесу і циклограми роботи плісирувальної машини ножового-валкового типу. Три основні виконавчі механізми працюють циклічно послідовно-паралельно в різних фазах. Регулювання параметрів складок-плісе (їх глибини і ширини) можливо здійснити за допомогою регулювання діапазону руху поршнів гідроциліндрів. За розробленими схемами представлено детальний опис будови нового гідророзподільника та узгодження роботи комплексного гідравлічного привода з механізмами плісирувальної машини. Гідравлічний розподільник нової конструкції може виконувати, як розподільну, так і керуючу функцію розподілення робочої рідини одночасно на три гідродвигуна виконавчих механізмів згідно з циклограмою роботи плісирувальної машини та може замінити керовані автоматичні пристрої. Внаслідок зменшення кількості деталей у плісирувальній машині з розробленим комплексним гідравлічним приводом спрощується її конструкція і технологія виготовлення в порівнянні з плісирувальними машинами електромеханічної дії за рахунок відсутності головного валу і механічних передач, які перетворюють і передають рухи від електродвигуна до виконавчих механізмів. Конструктивний метод розробки гідророзподільника комплексного гідропривода плісирувальної машини може бути використаний для інших машин, що мають механізмами, які працюють в різних фазах циклограми. Ключові слова: - комплексний гідравлічний привод, виконавчі механізми, плісирувальна машини, гідравлічний розподільник, циклова діаграма.

  • SYNTHESIS OF ADJUSTABLE MECHANISM OF SEWING MACHINE AND ITS KINEMATIC ANALYSIS USING SOLIDWORKS

    by Viacheslav Kharzhevskyi, Maksym Marchenko, Vitalii Tkachuk, Oleh Bereziuk, Khmelnytskyi National University, Vinnytsia National Technical University


  • THE USAGE OF COMPUTER-AIDED ENGINEERING SYSTEM “SOLIDWORKS MOTION” TO SOLVE THE PROBLEMS OF KINEMATICS AND DYNAMICS OF TECHNICAL SYSTEMS

    by Maksym Marchenko, Viacheslav Kharzhevskyi, Vitalii Tkachuk, Serhiy Horiashchenko, Khmelnytskyi National University

    The paper is dedicated to the problems of engineering analysis of technical systems by means of computer modeling, in particular the calculation of kinematic and dynamic characteristics of mechanisms and machines using the Computer-Aided Engineering system – SOLIDWORKS Motion, that allows to conduct numerical experiments to check the working capacity of mechanisms and machines, determine their main kinematical and dynamical characteristics, including for the purpose of further optimization according to various criteria. The paper shows results of the performed calculations of various types of mechanisms using examples used in the academic process within the course “Theory of Mechanisms and Machines”, which can be also successfully used within the design process, and includes examples of kinematic and dynamic analysis of linkage mechanisms, cam mechanisms, gear trains. In particular, the paper includes the simulation of the work process of the robot-manipulator using SOLIDWORKS Motion. It is shown that the usage of modern Computer-Aided Engineering systems (like SOLIDWORKS Motion or similar) enables to simplify the design process, shorten the design time and give an ability to carry out multi-parametric optimization procedures using different criteria, such as displacement values, velocities, accelerations, the values of reaction forces, overall dimensions etc. Besides, the usage of CAE-technologies enables to transform the academic process and makes it much more interesting or the students, who can use such technologies in their professional work in the future and become more competitive in the job market.


  • USING SOLIDWORKS FOR PROTOTYPING AERODYNAMIC STEERING DRIVES

    by Andriy Kushnirchuk, Vitalii Tkachuk, Vitalii Karazey, Viacheslav Kharzhevskyi, Maksym Marchenko, Khmelnytskyi National University