Artem Prokopchuk
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Artem Prokopchuk has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Arthur Ewert
Institute of Machine Elements and Machine Design Technische Universität Dresden Dresden Germany
8 shared publications - Thomas Wallmersperger
Institute of Solid Mechanics Technische Universität Dresden Dresden Germany
8 shared publications - Johannes Dieter Martin Menning
Institute of Solid Mechanics Technische Universität Dresden Dresden Germany
7 shared publications - Berthold Schlecht
Institute of Machine Elements and Machine Design Technische Universität Dresden Dresden Germany
5 shared publications - Thomas Rosenlöcher
Institute of Machine Elements and Machine Design, TU Dresden, Dresden, Germany
4 shared publications Berthold Schlecht
Institute of Machine Elements and Machine Design Technische Universität Dresden Dresden Germany
3 shared publications
Latest Publications
- Open Access
- 29 September 2026
- Published by Wiley in Proceedings in Applied Mathematics and Mechanics
- Vol. 26 (4)
Regression Model for a Sensor‐Integrating Jaw Coupling—Compensation for the Viscoelastic Material Behavior
In recent years, there has been an increasing demand to digitize production processes. In order to obtain the necessary data for these processes, numerous sensors must be installed on or in the machines. This can be difficult, especially when done retroactively, as the existing installation space must be able to accommodate the sensors. To address this issue, sensor‐integrating machine elements are currently being developed. In these machine elements, the sensors are integrated directly into the respective element, and thus enabling a space‐neutral installation. In the current work a sensor‐integrating jaw coupling is investigated. The aim of this coupling is to obtain the transmitted torque via measuring the deformation of the gear rim teeth. For this purpose, dielectric elastomer sensors (DESs), which change their capacitance when deformed, are employed. The functionality of this principle was shown in previous works. The gear rim material has viscoelastic properties. Thus, hysteresis occurs when plotting the torque (the measurand) versus the capacitance (the measured quantity). It follows, that to predict the torque based on the measured capacitance, a regression model is needed. For this task, two approaches are compared with each other: (i) a Gated Recurrent Unit (GRU), a type of recurrent neural network, and (ii) a physics‐based approach using a combination of analytical models with a GRU. The hyperparameters of the models were determined using the Python library “Optuna.” The models were trained using numerical data of the sensor‐integrating jaw coupling. The two models are compared in terms of the computational time required and their level of accuracy.
- 29 September 2026
- Published by Wiley in Proceedings in Applied Mathematics and Mechanics
- Vol. 26 (4)
Open AccessRegression Model for a Sensor‐Integrating Jaw Coupling—Compensation for the Viscoelastic Material Behavior
In recent years, there has been an increasing demand to digitize production processes. In order to obtain the necessary data for these processes, numerous sensors must be installed on or in the machines. This can be difficult, especially when done retroactively, as the existing installation space must be able to accommodate the sensors. To address this issue, sensor‐integrating machine elements are currently being developed. In these machine elements, the sensors are integrated directly into the respective element, and thus enabling a space‐neutral installation. In the current work a sensor‐integrating jaw coupling is investigated. The aim of this coupling is to obtain the transmitted torque via measuring the deformation of the gear rim teeth. For this purpose, dielectric elastomer sensors (DESs), which change their capacitance when deformed, are employed. The functionality of this principle was shown in previous works. The gear rim material has viscoelastic properties. Thus, hysteresis occurs when plotting the torque (the measurand) versus the capacitance (the measured quantity). It follows, that to predict the torque based on the measured capacitance, a regression model is needed. For this task, two approaches are compared with each other: (i) a Gated Recurrent Unit (GRU), a type of recurrent neural network, and (ii) a physics‐based approach using a combination of analytical models with a GRU. The hyperparameters of the models were determined using the Python library “Optuna.” The models were trained using numerical data of the sensor‐integrating jaw coupling. The two models are compared in terms of the computational time required and their level of accuracy.
- Open Access
- 10 April 2026
- Published by Wiley in Proceedings in Applied Mathematics and Mechanics
- Vol. 26 (2)
Numerical Modeling of the Thermo‐Mechanical and Electrical Behavior of a Sensor‐Integrating Jaw Coupling
Industry 4.0 requires more and more data from the production process, for example, on transmitted forces, torques and wear, in order to reduce expensive downtimes and to increase productivity. Direct or indirect methods can be used to collect this data. For direct measurement, the sensors can be integrated directly into the load‐bearing machine elements, thus creating a sensor‐integrating machine element. In order to investigate the effect of design choices on the performance of (i) the machine element or (ii) the sensors it is advantageous to create a numerical model for such a sensor‐integrated machine element. In the current work a sensor‐integrating jaw coupling, with which the torque can be measured via dielectric elastomer sensors (DESs), is investigated. The sensors are located in the individual teeth of the gear rim of the coupling. They change their capacitance when they are deformed. This is used to predict the torque. The gear rim of the jaw coupling is made of thermoplastic polyurethane (TPU), which has viscoelastic and temperature‐dependent properties. In order to be able to take these temperature‐dependent properties into account, an existing finite element model, in which a mechanical‐electrical model is implemented, is extended by the thermal field. Due to its use as a sensor, it has been shown that a one‐way coupling between the mechanical and electrical field is sufficient. With the proposed model, the heating of the gear rim due to loads with high frequencies and the effect of this heating on the capacitance change is analyzed. The numerical simulations have shown that the heating is concentrated at the tip of the gear rim tooth.
- 10 April 2026
- Published by Wiley in Proceedings in Applied Mathematics and Mechanics
- Vol. 26 (2)
Open AccessNumerical Modeling of the Thermo‐Mechanical and Electrical Behavior of a Sensor‐Integrating Jaw Coupling
Industry 4.0 requires more and more data from the production process, for example, on transmitted forces, torques and wear, in order to reduce expensive downtimes and to increase productivity. Direct or indirect methods can be used to collect this data. For direct measurement, the sensors can be integrated directly into the load‐bearing machine elements, thus creating a sensor‐integrating machine element. In order to investigate the effect of design choices on the performance of (i) the machine element or (ii) the sensors it is advantageous to create a numerical model for such a sensor‐integrated machine element. In the current work a sensor‐integrating jaw coupling, with which the torque can be measured via dielectric elastomer sensors (DESs), is investigated. The sensors are located in the individual teeth of the gear rim of the coupling. They change their capacitance when they are deformed. This is used to predict the torque. The gear rim of the jaw coupling is made of thermoplastic polyurethane (TPU), which has viscoelastic and temperature‐dependent properties. In order to be able to take these temperature‐dependent properties into account, an existing finite element model, in which a mechanical‐electrical model is implemented, is extended by the thermal field. Due to its use as a sensor, it has been shown that a one‐way coupling between the mechanical and electrical field is sufficient. With the proposed model, the heating of the gear rim due to loads with high frequencies and the effect of this heating on the capacitance change is analyzed. The numerical simulations have shown that the heating is concentrated at the tip of the gear rim tooth.
- 19 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
Radial Shaft Misalignments Measured by a Sensor-Integrating Jaw Coupling
The increasing demand for high-quality data in industrial applications - such as drive trains, test benches or pumping stations - poses significant challenges due to high costs for data acquisition. These costs often arise from required system modifications, extended downtimes and complex sensor-integration, even if existing systems are retrofitted with sensing capabilities. Sensor-integrating machine elements offer a promising solution by enabling in-situ data acquisition using a design space neutral approach. This paper investigates a sensor-integrating jaw coupling with integrated dielectric elastomer sensors. The focus lies on the indirect detection and evaluation of radial shaft misalignments, enabled by the sensor configuration and measurement chain. Experimental data are presented to validate the measurement concept. Furthermore, a previously proposed regression model is applied to quantify shaft misalignment based on the acquired measurements. The results indicate that the sensor-integrating coupling can be used as a multifunctional sensor-integrating machine element.
- 19 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
Radial Shaft Misalignments Measured by a Sensor-Integrating Jaw Coupling
The increasing demand for high-quality data in industrial applications - such as drive trains, test benches or pumping stations - poses significant challenges due to high costs for data acquisition. These costs often arise from required system modifications, extended downtimes and complex sensor-integration, even if existing systems are retrofitted with sensing capabilities. Sensor-integrating machine elements offer a promising solution by enabling in-situ data acquisition using a design space neutral approach. This paper investigates a sensor-integrating jaw coupling with integrated dielectric elastomer sensors. The focus lies on the indirect detection and evaluation of radial shaft misalignments, enabled by the sensor configuration and measurement chain. Experimental data are presented to validate the measurement concept. Furthermore, a previously proposed regression model is applied to quantify shaft misalignment based on the acquired measurements. The results indicate that the sensor-integrating coupling can be used as a multifunctional sensor-integrating machine element.
- Open Access
- 16 September 2025
- Published by Springer Nature in Forschung im Ingenieurwesen
- Vol. 89 (1) , 1-17
Numerical and experimental investigations of conventional and sensor-integrating jaw couplings
The possibility to directly measure the torque transmitted from a motor to a machine is not an easy task. To alleviate this, in the current work a new prototype of a sensor-integrating jaw coupling is proposed. In the prototype, double-sided counterbores are drilled into the teeth of the gear rim. Afterwards, dielectric elastomer sensors (DESs) are inserted, which are connected to strain amplifiers at both ends. The change in the capacitance of the sensors can then later be used to predict the torque. In the present work, the new prototype of the sensor-integrating jaw coupling is experimentally and numerically evaluated. Additionally, the manufactured DESs were subjected to multiple compressive loading-unloading cycles using a tensile testing machine to characterize them. It was shown for the first time that the coupling is able to detect the application of a torsion angle independent of the loading direction, i.e. clockwise or counterclockwise. Additionally, the correlation between the applied load and the measured change in capacitance is very good. Furthermore, a framework for the numerical simulation of both conventional and sensor-integrating jaw coupling is given and validated with experimental data. The model was implemented in the finite element software ABAQUS. To account for the viscous material properties of the material of the gear rim a hyper-viscoelastic material model was used. For the prediction of the torque, the numerical model yielded excellent results when compared to the experimental data.
- 16 September 2025
- Published by Springer Nature in Forschung im Ingenieurwesen
- Vol. 89 (1) , 1-17
Open AccessNumerical and experimental investigations of conventional and sensor-integrating jaw couplings
The possibility to directly measure the torque transmitted from a motor to a machine is not an easy task. To alleviate this, in the current work a new prototype of a sensor-integrating jaw coupling is proposed. In the prototype, double-sided counterbores are drilled into the teeth of the gear rim. Afterwards, dielectric elastomer sensors (DESs) are inserted, which are connected to strain amplifiers at both ends. The change in the capacitance of the sensors can then later be used to predict the torque. In the present work, the new prototype of the sensor-integrating jaw coupling is experimentally and numerically evaluated. Additionally, the manufactured DESs were subjected to multiple compressive loading-unloading cycles using a tensile testing machine to characterize them. It was shown for the first time that the coupling is able to detect the application of a torsion angle independent of the loading direction, i.e. clockwise or counterclockwise. Additionally, the correlation between the applied load and the measured change in capacitance is very good. Furthermore, a framework for the numerical simulation of both conventional and sensor-integrating jaw coupling is given and validated with experimental data. The model was implemented in the finite element software ABAQUS. To account for the viscous material properties of the material of the gear rim a hyper-viscoelastic material model was used. For the prediction of the torque, the numerical model yielded excellent results when compared to the experimental data.
- Open Access
- 1 August 2024
- Published by Wiley in Proceedings in Applied Mathematics and Mechanics
- Vol. 24 (2)
Numerical detection of shaft misalignments using a sensor‐integrating jaw coupling
Shaft misalignments are one of the main causes of damage to couplings in machines. If they are not detected in time, they can lead to machine downtimes. When assembling a machine, however, it is not always possible to align the shafts perfectly. Elastic couplings are able to compensate for such misalignments up to a certain degree. To detect the present radial misalignment, the concept of a sensor‐integrating jaw coupling, developed to determine the transmitted torque, is used. In the teeth of the gear rim, boreholes are drilled and dielectric elastomer sensors (DES) are inserted. If the teeth deform during use of the coupling the DES will deform as well, leading to a change in capacitance, which can be detected. If the two shafts, which the coupling connects, are perfectly aligned to each other, each of the loaded teeth will deform uniformly. However, if there is a radial or angular misalignment, the deformation is different for each tooth, which can be determined with the help of the DES. To demonstrate this effect, a finite element model of the sensor‐integrating jaw coupling with misalignments is created, and numerical simulations are conducted. In this model, the hyper‐viscoelastic material behavior of (i) the gear rim of the jaw coupling and (ii) the DES is taken into account. From the mechanical simulation, the deformed state of the DES is obtained, which is used to compute the capacitance of the sensor. With the results of the numerical simulations, a symbolic regression is performed. The result is an analytical formula that makes the accurate detection of the present radial misalignment possible. The developed framework can later be easily programmed on a microcontroller which is integrated in the sensor‐integrating jaw coupling.
- 1 August 2024
- Published by Wiley in Proceedings in Applied Mathematics and Mechanics
- Vol. 24 (2)
Open AccessNumerical detection of shaft misalignments using a sensor‐integrating jaw coupling
Shaft misalignments are one of the main causes of damage to couplings in machines. If they are not detected in time, they can lead to machine downtimes. When assembling a machine, however, it is not always possible to align the shafts perfectly. Elastic couplings are able to compensate for such misalignments up to a certain degree. To detect the present radial misalignment, the concept of a sensor‐integrating jaw coupling, developed to determine the transmitted torque, is used. In the teeth of the gear rim, boreholes are drilled and dielectric elastomer sensors (DES) are inserted. If the teeth deform during use of the coupling the DES will deform as well, leading to a change in capacitance, which can be detected. If the two shafts, which the coupling connects, are perfectly aligned to each other, each of the loaded teeth will deform uniformly. However, if there is a radial or angular misalignment, the deformation is different for each tooth, which can be determined with the help of the DES. To demonstrate this effect, a finite element model of the sensor‐integrating jaw coupling with misalignments is created, and numerical simulations are conducted. In this model, the hyper‐viscoelastic material behavior of (i) the gear rim of the jaw coupling and (ii) the DES is taken into account. From the mechanical simulation, the deformed state of the DES is obtained, which is used to compute the capacitance of the sensor. With the results of the numerical simulations, a symbolic regression is performed. The result is an analytical formula that makes the accurate detection of the present radial misalignment possible. The developed framework can later be easily programmed on a microcontroller which is integrated in the sensor‐integrating jaw coupling.
- 8 July 2024
- Published by Walter de Gruyter GmbH in Materials Testing
- Vol. 66 (9) , 1425-1438
Experimental investigations and material modeling of an elastomer jaw coupling
This work investigates the hyper-viscoelastic behavior of a thermoplastic polyurethane IROGRAN A 92 E 5670 FCM used in the gear rim of a jaw coupling. The aim is to provide the material parameters for the modeling of jaw couplings in engineering tasks. Uniaxial compression tests were conducted at various temperatures and loading speeds to fit a hyper-viscoelastic material model. The material model uses the Yeoh free energy and the power law model with one Maxwell element. The parametrized material model showed very good results in comparison to experimental data. In addition, the influence of friction on the experiments was modeled, investigated, and discussed. Further component tests for a jaw coupling of size 28 were conducted with two different specimen types. The original gear rim and a modified gear rim with central boreholes for integrated sensors were used in the test. The influence of such a modification was investigated with four different loading cases, focusing on the torsion-torque characteristic and the relative damping. These component tests enable the validation of numerical models of jaw couplings.
- 8 July 2024
- Published by Walter de Gruyter GmbH in Materials Testing
- Vol. 66 (9) , 1425-1438
Experimental investigations and material modeling of an elastomer jaw coupling
This work investigates the hyper-viscoelastic behavior of a thermoplastic polyurethane IROGRAN A 92 E 5670 FCM used in the gear rim of a jaw coupling. The aim is to provide the material parameters for the modeling of jaw couplings in engineering tasks. Uniaxial compression tests were conducted at various temperatures and loading speeds to fit a hyper-viscoelastic material model. The material model uses the Yeoh free energy and the power law model with one Maxwell element. The parametrized material model showed very good results in comparison to experimental data. In addition, the influence of friction on the experiments was modeled, investigated, and discussed. Further component tests for a jaw coupling of size 28 were conducted with two different specimen types. The original gear rim and a modified gear rim with central boreholes for integrated sensors were used in the test. The influence of such a modification was investigated with four different loading cases, focusing on the torsion-torque characteristic and the relative damping. These component tests enable the validation of numerical models of jaw couplings.
- Open Access
- 18 June 2024
- Published by Springer Nature in Forschung im Ingenieurwesen
- Vol. 88 (1) , 1-11
Concept of a sensor-integrating jaw coupling for measuring operating data
In recent years, industry and research (i) have driven the development and application of data-driven machines and systems and (ii) have increasingly introduced predictive maintenance. One of the main challenges is the acquisition of representative data for these applications. In the scope of mechanical systems, machine elements are the key parts for measuring process relevant data. Thereby, elastic couplings offer a considerable potential for a wide range of applications. The present work describes a novel space neutral sensor-integrating gear rim of a jaw coupling for the measurement of torque, rotational speed and temperature. The mechanical modifications on the coupling and the applied dielectric elastomer sensor are outlined. Additionally, the electrical conceptualization and the measurement chains are described. A manufactured prototype of the sensor-integrating jaw coupling and a proof of concept are presented.
- 18 June 2024
- Published by Springer Nature in Forschung im Ingenieurwesen
- Vol. 88 (1) , 1-11
Open AccessConcept of a sensor-integrating jaw coupling for measuring operating data
In recent years, industry and research (i) have driven the development and application of data-driven machines and systems and (ii) have increasingly introduced predictive maintenance. One of the main challenges is the acquisition of representative data for these applications. In the scope of mechanical systems, machine elements are the key parts for measuring process relevant data. Thereby, elastic couplings offer a considerable potential for a wide range of applications. The present work describes a novel space neutral sensor-integrating gear rim of a jaw coupling for the measurement of torque, rotational speed and temperature. The mechanical modifications on the coupling and the applied dielectric elastomer sensor are outlined. Additionally, the electrical conceptualization and the measurement chains are described. A manufactured prototype of the sensor-integrating jaw coupling and a proof of concept are presented.
- Open Access
- 28 February 2024
- Published by IOP Publishing in Engineering Research Express
- Vol. 6 (1) , 015403
Manufacturing of soft capacitive strain sensor based on dielectric elastomer material for an elastic element of a jaw coupling
In this work, we present a procedure for manufacturing a soft capacitive strain sensor in the form of a multi-layer electrical capacitor for further integration into the elastic gear rim of a jaw coupling. The dielectric elastomer sensor (DES) is based on an elastomeric substrate with alternating layers of conductive carbon black based ink as electrode layers and elastomeric film as a dielectric and electrical insulation. A variety of thin multi-layer sensors were produced to evaluate the manufacturing process. Additionally, using an LCR meter and a tensile test machine, the equivalent electrical capacitance (C) at the two sensor contacts and the applied force are measured, respectively. It is shown that C varies depending on the amount of sample strain caused by the applied force. By testing two versions of DES, a maximum change in capacitance of ΔC = 1.55 pF was achieved. The obtained characteristics show that the presented manufacturing process for the DES can be used as a soft strain sensor to measure the strain caused by the force applied to the elastic element between the jaw couplings.
- 28 February 2024
- Published by IOP Publishing in Engineering Research Express
- Vol. 6 (1) , 015403
Open AccessManufacturing of soft capacitive strain sensor based on dielectric elastomer material for an elastic element of a jaw coupling
In this work, we present a procedure for manufacturing a soft capacitive strain sensor in the form of a multi-layer electrical capacitor for further integration into the elastic gear rim of a jaw coupling. The dielectric elastomer sensor (DES) is based on an elastomeric substrate with alternating layers of conductive carbon black based ink as electrode layers and elastomeric film as a dielectric and electrical insulation. A variety of thin multi-layer sensors were produced to evaluate the manufacturing process. Additionally, using an LCR meter and a tensile test machine, the equivalent electrical capacitance (C) at the two sensor contacts and the applied force are measured, respectively. It is shown that C varies depending on the amount of sample strain caused by the applied force. By testing two versions of DES, a maximum change in capacitance of ΔC = 1.55 pF was achieved. The obtained characteristics show that the presented manufacturing process for the DES can be used as a soft strain sensor to measure the strain caused by the force applied to the elastic element between the jaw couplings.
- Open Access
Dielectric Permittivity Model for Polymer–Filler Composite Materials by the Example of Ni- and Graphite-Filled Composites for High-Frequency Absorbing Coatings
The suppression of unnecessary radio-electronic noise and the protection of electronic devices from electromagnetic interference by the use of pliable highly microwave radiation absorbing composite materials based on polymers or rubbers filled with conductive and magnetic fillers have been proposed. Since the working frequency bands of electronic devices and systems are rapidly expanding up to the millimeter wave range, the capabilities of absorbing and shielding composites should be evaluated for increasing operating frequency. The point is that the absorption capacity of conductive and magnetic fillers essentially decreases as the frequency increases. Therefore, this paper is devoted to the absorbing capabilities of composites filled with high-loss dielectric fillers, in which absorption significantly increases as frequency rises, and it is possible to achieve the maximum frequency selective of absorption due to electromagnetic and electromechanical resonances.
Open AccessDielectric Permittivity Model for Polymer–Filler Composite Materials by the Example of Ni- and Graphite-Filled Composites for High-Frequency Absorbing Coatings
The suppression of unnecessary radio-electronic noise and the protection of electronic devices from electromagnetic interference by the use of pliable highly microwave radiation absorbing composite materials based on polymers or rubbers filled with conductive and magnetic fillers have been proposed. Since the working frequency bands of electronic devices and systems are rapidly expanding up to the millimeter wave range, the capabilities of absorbing and shielding composites should be evaluated for increasing operating frequency. The point is that the absorption capacity of conductive and magnetic fillers essentially decreases as the frequency increases. Therefore, this paper is devoted to the absorbing capabilities of composites filled with high-loss dielectric fillers, in which absorption significantly increases as frequency rises, and it is possible to achieve the maximum frequency selective of absorption due to electromagnetic and electromechanical resonances.