Marco Negozio
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Marco Negozio has a total of 42 co-authors. Here are the top co-authors by number of shared publications:
Adrian H. A. Lutey
Department of Engineering for Industrial Systems and Technologies (DISTI), University of Parma, Parco Area Delle Scienze, Parma, Italy
5 shared publications- Barbara Reggiani
University of Modena and Reggio Emilia
4 shared publications - Lorenzo Donati
University of Bologna
4 shared publications - Sara Bocchi
University of Bergamo
4 shared publications Lorenzo Donati
Dipartimento di Ingegneria Industriale (DIN), Università di Bologna, Bologna, Italy
3 shared publications- Riccardo Pelaccia
University of Modena and Reggio Emilia
3 shared publications
Latest Publications
- Open Access
- 29 August 2026
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 146 (5-6) , 4147-4167
A predictive framework for friction stir extrusion of AA6061 powder: coupling thermomechanical evolution, bonding and hardness
Friction Stir Extrusion (FSE) is emerging as a promising solid-state manufacturing process for the consolidation of fragmented aluminum feedstock such as machining chips and powder, offering substantial energy savings over conventional remelting. Despite its growing relevance, a comprehensive understanding of how FSE process parameters affect thermomechanical evolution and final mechanical properties remains incomplete. In this study, cylindrical AA6061 extrudates of diameter 7 mm were produced by varying tool rotational speed (200–1000 rpm) and feed rate (1–4 mm/s). Vickers microhardness was measured within core and crown regions of specimens cut from the front, middle and back of each sample. A 3D finite element model was developed in Qform UK to simulate temperature, strain, strain rate and bonding evolution throughout the process, enabling quantification of the maximum extrusion temperature, radial distributions of the strain and strain rate, and die advancement required for full consolidation of particles. The final aim of this work was to establish qualitative and quantitative relationships between FSE process parameters, thermomechanical evolution and local mechanical properties of extruded wires, thereby providing a predictive tool for process design and sustainable industrial application. Finally, a composite parameter (P FSE ) was introduced to improve predictive capability, providing a quantitative basis for FSE process optimization.
- 29 August 2026
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 146 (5-6) , 4147-4167
Open AccessA predictive framework for friction stir extrusion of AA6061 powder: coupling thermomechanical evolution, bonding and hardness
Friction Stir Extrusion (FSE) is emerging as a promising solid-state manufacturing process for the consolidation of fragmented aluminum feedstock such as machining chips and powder, offering substantial energy savings over conventional remelting. Despite its growing relevance, a comprehensive understanding of how FSE process parameters affect thermomechanical evolution and final mechanical properties remains incomplete. In this study, cylindrical AA6061 extrudates of diameter 7 mm were produced by varying tool rotational speed (200–1000 rpm) and feed rate (1–4 mm/s). Vickers microhardness was measured within core and crown regions of specimens cut from the front, middle and back of each sample. A 3D finite element model was developed in Qform UK to simulate temperature, strain, strain rate and bonding evolution throughout the process, enabling quantification of the maximum extrusion temperature, radial distributions of the strain and strain rate, and die advancement required for full consolidation of particles. The final aim of this work was to establish qualitative and quantitative relationships between FSE process parameters, thermomechanical evolution and local mechanical properties of extruded wires, thereby providing a predictive tool for process design and sustainable industrial application. Finally, a composite parameter (P FSE ) was introduced to improve predictive capability, providing a quantitative basis for FSE process optimization.
- Open Access
- 15 April 2026
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 1185, 29-39
Experimental and Numerical Evaluation of L-PBF Printed Tool for Friction Stir Welding
In Friction Stir Welding (FSW) tool geometry plays a critical role in governing heat generation, material flow, and microstructural evolution within the weld. In this study, the feasibility and performance of FSW tools manufactured by Laser Powder Bed Fusion (L-PBF) are experimentally and numerically investigated. A non-conventional FSW tool produced in AISI 316L by L-PBF was designed and compared with a conventional machined steel tool in the welding of AA6082-T6 sheets performed using already optimized process parameters. This was followed by tensile testing and macro-and micro-hardness measurements, and a punctual microstructural analysis. In addition, a 3D thermo-mechanical finite element model was employed to forecast and analyze the temperature distribution, the effective strain and the overall material flow. The results show that the tool manufactured using L-PBF enables FSW joints to achieve mechanical properties and welding efficiency similar to those of the standard tool. Finite Elements Models (FEM), in good agreement with experimental results, show that the geometry of the additive tool promotes greater plastic deformation and lower peak temperatures, confirming both the validity of the model and the suitability of L-PBF for the advanced design of FSW tools.
- 15 April 2026
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 1185, 29-39
Open AccessExperimental and Numerical Evaluation of L-PBF Printed Tool for Friction Stir Welding
In Friction Stir Welding (FSW) tool geometry plays a critical role in governing heat generation, material flow, and microstructural evolution within the weld. In this study, the feasibility and performance of FSW tools manufactured by Laser Powder Bed Fusion (L-PBF) are experimentally and numerically investigated. A non-conventional FSW tool produced in AISI 316L by L-PBF was designed and compared with a conventional machined steel tool in the welding of AA6082-T6 sheets performed using already optimized process parameters. This was followed by tensile testing and macro-and micro-hardness measurements, and a punctual microstructural analysis. In addition, a 3D thermo-mechanical finite element model was employed to forecast and analyze the temperature distribution, the effective strain and the overall material flow. The results show that the tool manufactured using L-PBF enables FSW joints to achieve mechanical properties and welding efficiency similar to those of the standard tool. Finite Elements Models (FEM), in good agreement with experimental results, show that the geometry of the additive tool promotes greater plastic deformation and lower peak temperatures, confirming both the validity of the model and the suitability of L-PBF for the advanced design of FSW tools.
- Open Access
- 14 April 2026
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 1048, 25-34
Numerical Investigation of Round Profile Production: A Fem-Based Comparison between Friction Stir Extrusion and Conventional Extrusion
Friction Stir Extrusion (FSE), Direct Extrusion (DE) and Indirect Extrusion (IE) are all valid processes for the production of round profiles. However, differences and similarities between them have yet to be analyzed by the scientific community, since with the same geometry, each technology instills specific properties to the extruded product. In this context, the present work proposes an in-depth analysis via QForm UK Finite Element Method (FEM) software of the effect that each process has on a AA6061 extruded wire. Various combinations of rotational speed (200, 400, 600 rpm), feed rate (1, 2, 3, 4 mm/s) and pre-heating temperature (450, 500°C) were analyzed to assess differences and similarities between FSE, DE and IE. The feedstock material for FSE was chosen to be powder, while a solid billet was used for conventional extrusion.
- 14 April 2026
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 1048, 25-34
Open AccessNumerical Investigation of Round Profile Production: A Fem-Based Comparison between Friction Stir Extrusion and Conventional Extrusion
Friction Stir Extrusion (FSE), Direct Extrusion (DE) and Indirect Extrusion (IE) are all valid processes for the production of round profiles. However, differences and similarities between them have yet to be analyzed by the scientific community, since with the same geometry, each technology instills specific properties to the extruded product. In this context, the present work proposes an in-depth analysis via QForm UK Finite Element Method (FEM) software of the effect that each process has on a AA6061 extruded wire. Various combinations of rotational speed (200, 400, 600 rpm), feed rate (1, 2, 3, 4 mm/s) and pre-heating temperature (450, 500°C) were analyzed to assess differences and similarities between FSE, DE and IE. The feedstock material for FSE was chosen to be powder, while a solid billet was used for conventional extrusion.
- Open Access
- 14 April 2026
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 1048, 133-150
Comparative Characterization through Torsion Tests of Primary and Secondary Aluminum Alloys for the Extrusion Process
In the transition to a circular economy in the automotive sector, it is essential to integrate recycled (or secondary) aluminum alloys into extrusion processes, while ensuring that their performance is as close as possible to that of primary alloys. Within the Horizon Europe ZEvRA project, this study aims to analyze and investigate the hot deformation behavior of four aluminum alloys, two primary alloys (AA6082 Primary and AA7108) and two recycled alloys (AA6082 Recycled and AA6061), in order to demonstrate their potential suitability for automotive applications. Hot torsion tests were conducted under temperature and strain rate conditions representative of industrial extrusion processes. Four different temperatures (400, 450, 500, and 550 °C) and four different strain rates (0.01, 0.1, 1, and 10 s⁻¹) were investigated, allowing the achievement of significantly higher strain levels compared to conventional standard tensile and compression tests. Subsequently, the flow stress curves obtained from the torsion tests were analyzed to evaluate the influence of temperature and strain rate on the plastic deformation behavior of the material and on the associated dynamic softening mechanisms. The results demonstrate a comparable deformation behavior between primary and secondary alloys, confirming the feasibility and full compatibility of recycled alloys for high-performance industrial extrusion applications. Furthermore, the experimental results provide a solid basis for the development of robust constitutive models to support FEM simulations aimed at optimizing metal forming pocesses within a circular manufacturing framework.
- 14 April 2026
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 1048, 133-150
Open AccessComparative Characterization through Torsion Tests of Primary and Secondary Aluminum Alloys for the Extrusion Process
In the transition to a circular economy in the automotive sector, it is essential to integrate recycled (or secondary) aluminum alloys into extrusion processes, while ensuring that their performance is as close as possible to that of primary alloys. Within the Horizon Europe ZEvRA project, this study aims to analyze and investigate the hot deformation behavior of four aluminum alloys, two primary alloys (AA6082 Primary and AA7108) and two recycled alloys (AA6082 Recycled and AA6061), in order to demonstrate their potential suitability for automotive applications. Hot torsion tests were conducted under temperature and strain rate conditions representative of industrial extrusion processes. Four different temperatures (400, 450, 500, and 550 °C) and four different strain rates (0.01, 0.1, 1, and 10 s⁻¹) were investigated, allowing the achievement of significantly higher strain levels compared to conventional standard tensile and compression tests. Subsequently, the flow stress curves obtained from the torsion tests were analyzed to evaluate the influence of temperature and strain rate on the plastic deformation behavior of the material and on the associated dynamic softening mechanisms. The results demonstrate a comparable deformation behavior between primary and secondary alloys, confirming the feasibility and full compatibility of recycled alloys for high-performance industrial extrusion applications. Furthermore, the experimental results provide a solid basis for the development of robust constitutive models to support FEM simulations aimed at optimizing metal forming pocesses within a circular manufacturing framework.
- Open Access
- 14 April 2026
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 1048, 151-164
Transient Thermal Analysis of Multiple Extrusion Runs with Nitrogen Cooling by Means of Qform Code
In hot extrusion of light alloys, nitrogen cooling has become a strategic solution to mitigate thermal issues from high deformation rates and frictional heating, improving surface quality, extrusion speed, and die life. However, current cooling system designs remain largely empirical, and the limited use of predictive modeling and experimental monitoring often leads to inconsistent evaluations. This work proposes a dual-step procedure for transient numerical analysis of multiple billets with nitrogen cooling. First, a 1D numerical model of nitrogen cooling is simulated in a simplified environment reproducing extrusion thermal conditions, requiring negligible computational time. The resulting heat transfer coefficient (HTC) and nitrogen temperature are then integrated into the process model, implemented in Qform code, as additional boundary conditions. This approach enables the fully 3D extrusion model to account for nitrogen cooling effects not only on thermal gradients but also on aluminium flow and die resistance. A porthole die with three tube-shaped openings for hollow profile extrusion was experimentally tested under cooled and uncooled conditions, with thermal behaviour monitored by eleven thermocouples within the tooling set. Experimental–numerical comparison confirmed the advantages of numerical simulation for cooling channel design and the limitations of experience-based approaches.
- 14 April 2026
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 1048, 151-164
Open AccessTransient Thermal Analysis of Multiple Extrusion Runs with Nitrogen Cooling by Means of Qform Code
In hot extrusion of light alloys, nitrogen cooling has become a strategic solution to mitigate thermal issues from high deformation rates and frictional heating, improving surface quality, extrusion speed, and die life. However, current cooling system designs remain largely empirical, and the limited use of predictive modeling and experimental monitoring often leads to inconsistent evaluations. This work proposes a dual-step procedure for transient numerical analysis of multiple billets with nitrogen cooling. First, a 1D numerical model of nitrogen cooling is simulated in a simplified environment reproducing extrusion thermal conditions, requiring negligible computational time. The resulting heat transfer coefficient (HTC) and nitrogen temperature are then integrated into the process model, implemented in Qform code, as additional boundary conditions. This approach enables the fully 3D extrusion model to account for nitrogen cooling effects not only on thermal gradients but also on aluminium flow and die resistance. A porthole die with three tube-shaped openings for hollow profile extrusion was experimentally tested under cooled and uncooled conditions, with thermal behaviour monitored by eleven thermocouples within the tooling set. Experimental–numerical comparison confirmed the advantages of numerical simulation for cooling channel design and the limitations of experience-based approaches.
- 16 March 2026
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 143 (11-12) , 6253-6267
A geometry-based predictive framework for charge welds: a tool for extrusion scrap reduction and die design optimization
- 16 March 2026
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 143 (11-12) , 6253-6267
A geometry-based predictive framework for charge welds: a tool for extrusion scrap reduction and die design optimization
- Open Access
- 21 December 2025
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 142 (3-4) , 1797-1817
Ultrashort pulsed laser texturing of Li-ion battery current collectors: modeling mechanical stress during cycling
The finite element method (FEM) is employed within COMSOL Multiphysics to simulate mechanical stress during cycling of Li-ion battery electrodes with ultrashort pulsed laser-textured current collectors. Two- and three-dimensional models of electrodes with flat (untextured) current collectors are firstly compared, after which a parametric study is performed with the 2D model to determine the effects of current collector topography and active material porosity on the resulting stress distribution during lithiation of the anode and delithiation of the cathode. The first principal stress (σ 1 ) is evaluated within the active materials due to their fragile nature, while the Von Mises stress (σ v ) is evaluated within the current collects due to their ductile nature. Normal ( p ) and shear (τ) contact pressures are evaluated at the interface between the two layers as indicators of the likelihood of delamination. Stress concentration at and near the interface between laser-textured current collectors and electrode active materials is shown to induce significant increases in peak stresses, with all evaluated parameters exhibiting strong dependence on the aspect ratio of the current collector surface topography. Approximately one-order-of-magnitude increases in σ 1 , p and τ are observed with a texture aspect ratio of 1, while σ v approximately doubles. Over the same range of parameters, the theoretical increase in interface area between the current collector and active material is approximately +130%, implying that selection of laser parameters to achieve a given surface topography must be a compromise between improving adhesion and limiting stress concentration during electrochemical cycling.
- 21 December 2025
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 142 (3-4) , 1797-1817
Open AccessUltrashort pulsed laser texturing of Li-ion battery current collectors: modeling mechanical stress during cycling
The finite element method (FEM) is employed within COMSOL Multiphysics to simulate mechanical stress during cycling of Li-ion battery electrodes with ultrashort pulsed laser-textured current collectors. Two- and three-dimensional models of electrodes with flat (untextured) current collectors are firstly compared, after which a parametric study is performed with the 2D model to determine the effects of current collector topography and active material porosity on the resulting stress distribution during lithiation of the anode and delithiation of the cathode. The first principal stress (σ 1 ) is evaluated within the active materials due to their fragile nature, while the Von Mises stress (σ v ) is evaluated within the current collects due to their ductile nature. Normal ( p ) and shear (τ) contact pressures are evaluated at the interface between the two layers as indicators of the likelihood of delamination. Stress concentration at and near the interface between laser-textured current collectors and electrode active materials is shown to induce significant increases in peak stresses, with all evaluated parameters exhibiting strong dependence on the aspect ratio of the current collector surface topography. Approximately one-order-of-magnitude increases in σ 1 , p and τ are observed with a texture aspect ratio of 1, while σ v approximately doubles. Over the same range of parameters, the theoretical increase in interface area between the current collector and active material is approximately +130%, implying that selection of laser parameters to achieve a given surface topography must be a compromise between improving adhesion and limiting stress concentration during electrochemical cycling.
- Open Access
- 27 March 2025
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 34 (12) , 11292
Correction: Experimental Investigation and Finite Element Simulation of the Microstructural Evolution in AA6082 Friction Stir Welded Joints
- 27 March 2025
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 34 (12) , 11292
Open AccessCorrection: Experimental Investigation and Finite Element Simulation of the Microstructural Evolution in AA6082 Friction Stir Welded Joints
- Open Access
- 19 March 2025
- Published by Springer Nature in Scientific Reports
- Vol. 15 (1) , 1-19
Smart extrusion via data-driven prediction of grain size and peripheral coarse grain defect formation
Optimization of the mechanical and crash properties of extruded AA6XXX automotive profiles requires detailed understanding of grain size evolution and formation of the peripheral coarse grain (PCG) defect. Conventional approaches demand extensive experimental campaigns which, further to being lengthy and resource-intensive, often lead to the adoption of conservative process parameters that limit production efficiency. The present work proposes a data-driven method for predicting grain size and PCG formation, combining finite element method (FEM) simulation data with experimental microstructural observations to train machine learning (ML) algorithms for classification and regression. Over 22,000 data points were collected from two distinct AA6082 aluminum alloy profiles with different geometries, extruded over a range of different process conditions. Hyperparameter optimization of artificial neural networks (ANNs) for regression and prediction was performed, with ANN outcomes benchmarked against existing analytical models. PCG formation was predicted with 5.8% false negatives and 3.9% false positives compared to 10.1% and 18.1%, respectively, with existing analytical models, while grain size was predicted with a mean squared error (MSE) of 9.77 μm2 compared to 48.3 μm2. PCG and grain size maps were then produced to demonstrate how prediction of grain size and PCG formation can be employed in a smart manufacturing environment.
- 19 March 2025
- Published by Springer Nature in Scientific Reports
- Vol. 15 (1) , 1-19
Open AccessSmart extrusion via data-driven prediction of grain size and peripheral coarse grain defect formation
Optimization of the mechanical and crash properties of extruded AA6XXX automotive profiles requires detailed understanding of grain size evolution and formation of the peripheral coarse grain (PCG) defect. Conventional approaches demand extensive experimental campaigns which, further to being lengthy and resource-intensive, often lead to the adoption of conservative process parameters that limit production efficiency. The present work proposes a data-driven method for predicting grain size and PCG formation, combining finite element method (FEM) simulation data with experimental microstructural observations to train machine learning (ML) algorithms for classification and regression. Over 22,000 data points were collected from two distinct AA6082 aluminum alloy profiles with different geometries, extruded over a range of different process conditions. Hyperparameter optimization of artificial neural networks (ANNs) for regression and prediction was performed, with ANN outcomes benchmarked against existing analytical models. PCG formation was predicted with 5.8% false negatives and 3.9% false positives compared to 10.1% and 18.1%, respectively, with existing analytical models, while grain size was predicted with a mean squared error (MSE) of 9.77 μm2 compared to 48.3 μm2. PCG and grain size maps were then produced to demonstrate how prediction of grain size and PCG formation can be employed in a smart manufacturing environment.
- Open Access
- 24 February 2025
- Published by Elsevier in Journal of Materials Science & Technology
- Vol. 230, 80-92
Impact of die design and bearing geometry on grain size and PCG formation during extrusion of AA6082 aluminum alloy
- 24 February 2025
- Published by Elsevier in Journal of Materials Science & Technology
- Vol. 230, 80-92
Open AccessImpact of die design and bearing geometry on grain size and PCG formation during extrusion of AA6082 aluminum alloy