Piji Feng
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Piji Feng has a total of 20 co-authors. Here are the top co-authors by number of shared publications:
- Guangtong Ma
Southwest Jiaotong University
8 shared publications - Jun Luo
Southwest Jiaotong University
8 shared publications - Zhenhua Su
Southwest Jiaotong University
7 shared publications - Libin Cui
State Key Laboratory of Rail Transit Vehicle System, Southwest Jiaotong University, Chengdu, China
6 shared publications - Guanglai Huang
State Key Laboratory of Rail Transit Vehicle System, Southwest Jiaotong University, Chengdu, China
2 shared publications Taoning Zhu
State Key Laboratory of Rail Transit Vehicle System, Southwest Jiaotong University, Chengdu, China
2 shared publications
Latest Publications
- 13 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Transportation Electrification
- Vol. 12 (3) , 5231-5242
Analytical Modeling of Multi-DOF Permanent Magnet Linear Braking via Equivalent Circuit Method
The permanent magnet linear braking (PMLB) has garnered significant attention for its contactless operation and high force density. However, conventional analytical models often exhibit limited accuracy due to oversimplified geometric assumptions and the inability to accommodate the multidegree-of-freedom (DOF) attitude variations of the mover. To address these limitations, this article presents a novel 3-D analytical model based on an equivalent circuit method. Specifically, the permanent magnet (PM) is equivalently represented as a rectangular current-carrying coil using the surface current method. The mutual inductance between this equivalent PM coil and the brake coil is calculated via the discrete Neumann formula. A dynamic equivalent circuit is then constructed to determine the induced currents in the brake coil, and the resulting braking force is evaluated using both the energy method and the method of images. The proposed model is thoroughly validated through finite element method (FEM) simulations. Additionally, the impact of various attitude conditions on braking performance is systematically analyzed. Finally, experimental results obtained from a full-scale prototype and measurement system show excellent agreement with the theoretical predictions, thereby confirming the model’s accuracy and practical applicability.
- 13 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Transportation Electrification
- Vol. 12 (3) , 5231-5242
Analytical Modeling of Multi-DOF Permanent Magnet Linear Braking via Equivalent Circuit Method
The permanent magnet linear braking (PMLB) has garnered significant attention for its contactless operation and high force density. However, conventional analytical models often exhibit limited accuracy due to oversimplified geometric assumptions and the inability to accommodate the multidegree-of-freedom (DOF) attitude variations of the mover. To address these limitations, this article presents a novel 3-D analytical model based on an equivalent circuit method. Specifically, the permanent magnet (PM) is equivalently represented as a rectangular current-carrying coil using the surface current method. The mutual inductance between this equivalent PM coil and the brake coil is calculated via the discrete Neumann formula. A dynamic equivalent circuit is then constructed to determine the induced currents in the brake coil, and the resulting braking force is evaluated using both the energy method and the method of images. The proposed model is thoroughly validated through finite element method (FEM) simulations. Additionally, the impact of various attitude conditions on braking performance is systematically analyzed. Finally, experimental results obtained from a full-scale prototype and measurement system show excellent agreement with the theoretical predictions, thereby confirming the model’s accuracy and practical applicability.
- 24 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 73 (2) , 2791-2800
3-D Modeling and Optimization of a High Overload PMLSM Based on Equivalent Mutual Inductance
Coreless permanent magnet linear synchronous motors (PMLSMs) are renowned for the high overload capacity, lightweight design, and outstanding thrust acceleration. However, the nonuniform magnetic field distribution at the longitudinal ends of the motor and the transverse arc edges of the primary windings give rise to significant end effects. Traditional modeling approaches are often computationally intensive or are limited to considering merely a single type of end effect. This article proposes a generalized modeling methodology capable of simultaneously accounting for both transverse and longitudinal end effects. By employing the equivalent surface current method and the method of images, the approach constructs a spatial coordinate matrix for both the permanent magnets (PMs) and thrust coils, thereby efficiently addressing the equivalent mutual inductance. To further optimize motor performance, the modified nondominated sorting genetic algorithm III (NSGA-III), incorporating adaptive crossover and mutation operators, is utilized to enhance thrust density, reduce ripples, and minimize manufacturing deviations. The efficiency of the proposed method is validated through finite element simulations and prototype experiments, with results showing a close agreement with theoretical predictions.
- 24 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 73 (2) , 2791-2800
3-D Modeling and Optimization of a High Overload PMLSM Based on Equivalent Mutual Inductance
Coreless permanent magnet linear synchronous motors (PMLSMs) are renowned for the high overload capacity, lightweight design, and outstanding thrust acceleration. However, the nonuniform magnetic field distribution at the longitudinal ends of the motor and the transverse arc edges of the primary windings give rise to significant end effects. Traditional modeling approaches are often computationally intensive or are limited to considering merely a single type of end effect. This article proposes a generalized modeling methodology capable of simultaneously accounting for both transverse and longitudinal end effects. By employing the equivalent surface current method and the method of images, the approach constructs a spatial coordinate matrix for both the permanent magnets (PMs) and thrust coils, thereby efficiently addressing the equivalent mutual inductance. To further optimize motor performance, the modified nondominated sorting genetic algorithm III (NSGA-III), incorporating adaptive crossover and mutation operators, is utilized to enhance thrust density, reduce ripples, and minimize manufacturing deviations. The efficiency of the proposed method is validated through finite element simulations and prototype experiments, with results showing a close agreement with theoretical predictions.
- 6 August 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Transportation Electrification
- Vol. 11 (6) , 12818-12829
Dynamic Characteristics Analysis and Enhancement for Superconducting EDS Trains at Curved Track
The studies of superconducting electrodynamic suspension (EDS) have gradually received more and more attention in recent years. As the inevitable line condition, the horizontal curved track would change the relative spatial position between the onboard superconducting magnet (SCM) and ground levitation/guidance (LG) coils, resulting in different vehicle–track coupled forces compared to straight track conditions, which prominently influences the dynamic performance of EDS trains. This article proposed an analytical calculation method of vehicle–track force that can describe arbitrary curved track parameters. Based on this calculation method, the dynamic model of EDS trains considering the curved track conditions was built. Meanwhile, an equivalent loading method for track irregularities was proposed, which is applicable to both real electromagnetic force case and fitting force case in dynamic scenarios. The calculation results indicate that under curved track conditions, the lateral and rolling dynamic characteristics of vehicles deteriorate significantly, and the effect of the higher harmonics of electromagnetic forces is enhanced. In order to suppress the violent vibration of SCMs, a ground-hook semi-active strategy at the primary suspension was adopted, and the results indicate that it can effectively improve the lateral displacements and accelerations of SCM units, but the suppressing effect of high-frequency vibrations is moderate. This research provides valuable references to clarify the dynamic characteristics of EDS trains at curved track and a new approach to suppress the vibrations of SCMs.
- 6 August 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Transportation Electrification
- Vol. 11 (6) , 12818-12829
Dynamic Characteristics Analysis and Enhancement for Superconducting EDS Trains at Curved Track
The studies of superconducting electrodynamic suspension (EDS) have gradually received more and more attention in recent years. As the inevitable line condition, the horizontal curved track would change the relative spatial position between the onboard superconducting magnet (SCM) and ground levitation/guidance (LG) coils, resulting in different vehicle–track coupled forces compared to straight track conditions, which prominently influences the dynamic performance of EDS trains. This article proposed an analytical calculation method of vehicle–track force that can describe arbitrary curved track parameters. Based on this calculation method, the dynamic model of EDS trains considering the curved track conditions was built. Meanwhile, an equivalent loading method for track irregularities was proposed, which is applicable to both real electromagnetic force case and fitting force case in dynamic scenarios. The calculation results indicate that under curved track conditions, the lateral and rolling dynamic characteristics of vehicles deteriorate significantly, and the effect of the higher harmonics of electromagnetic forces is enhanced. In order to suppress the violent vibration of SCMs, a ground-hook semi-active strategy at the primary suspension was adopted, and the results indicate that it can effectively improve the lateral displacements and accelerations of SCM units, but the suppressing effect of high-frequency vibrations is moderate. This research provides valuable references to clarify the dynamic characteristics of EDS trains at curved track and a new approach to suppress the vibrations of SCMs.
- 1 November 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Transportation Electrification
- Vol. 11 (2) , 5709-5722
Dynamic Characteristics and Protection Strategy for Superconducting Electrodynamic Suspension Train With Quenched Magnet
Superconducting magnet (SCM), as one of the key components of superconducting electrodynamic suspension (EDS) train, plays a critical role in load capacity and service safety. Quench behavior of SCM not only reduces the ride comfort but also increases the risk of accidents for the train, especially at high speeds where it becomes more dangerous and uncontrollable. Therefore, to evaluate the influence of quench conditions, this article proposes a dynamic model that considers the protective effect of auxiliary wheels when quench behavior occurs on the SCM. By controlling the variable resistance of SCM in the improved electromagnetic model, a switch can be realized among the normal and quench conditions. Furthermore, regarding the EDS train with propulsion, levitation, and guidance (PLG) coils as an object, the dynamic characteristics and magnetoelectric force coupling mechanism are analyzed and revealed under different quench positions. Finally, based on the analysis above, an emergency protection strategy is put forward by releasing energy from SCM on the opposite side of quench magnet. The results show that the strategy is able to avoid a sharp increase in guidance force and makes the re-stabilization possible in lateral dynamics, providing a valuable solution for coping with the quench condition of EDS train.
- 1 November 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Transportation Electrification
- Vol. 11 (2) , 5709-5722
Dynamic Characteristics and Protection Strategy for Superconducting Electrodynamic Suspension Train With Quenched Magnet
Superconducting magnet (SCM), as one of the key components of superconducting electrodynamic suspension (EDS) train, plays a critical role in load capacity and service safety. Quench behavior of SCM not only reduces the ride comfort but also increases the risk of accidents for the train, especially at high speeds where it becomes more dangerous and uncontrollable. Therefore, to evaluate the influence of quench conditions, this article proposes a dynamic model that considers the protective effect of auxiliary wheels when quench behavior occurs on the SCM. By controlling the variable resistance of SCM in the improved electromagnetic model, a switch can be realized among the normal and quench conditions. Furthermore, regarding the EDS train with propulsion, levitation, and guidance (PLG) coils as an object, the dynamic characteristics and magnetoelectric force coupling mechanism are analyzed and revealed under different quench positions. Finally, based on the analysis above, an emergency protection strategy is put forward by releasing energy from SCM on the opposite side of quench magnet. The results show that the strategy is able to avoid a sharp increase in guidance force and makes the re-stabilization possible in lateral dynamics, providing a valuable solution for coping with the quench condition of EDS train.
- 5 September 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Transportation Electrification
- Vol. 11 (1) , 4157-4168
Dynamic Modeling and Analysis of Vehicle-Track–Bridge Coupled System for Superconducting EDS Train
The superconducting electrodynamic suspension (EDS) train is the only high-speed manned transportation system that can reach 600 km/h, bringing into focus on its dynamic performance and ride quality in recent years. However, there has been little research that elucidated the coupling mechanisms among the vehicle, track and bridge, which makes the accurate characterization and reliable evaluation of dynamic performance difficult. In this paper, the 66 degree-of-freedom (DOF) numerical dynamic model of the EDS train is built. Afterwards, electromagnetic forces are calculated and the relationship among the electromagnetic forces and the attitude of superconducting magnet (SCM) unit is described with the Response Surface Method (RSM) and its reliability is validated. Subsequently, the numerical model of the bridge is established. Using electromagnetic forces to connect vehicle and bridge, the vehicle-track-bridge coupled EDS system was eventually built. By means of these, the results illustrate that the resonance occurs mainly in the range of 350 km/h to 400 km/h and benefits from the weak coupled relationship between vehicle and bridge, the coupled vibration is not prominent. These results confirm the potential of EDS in high-speed transit field and a useful reference is provided for its engineering application.
- 5 September 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Transportation Electrification
- Vol. 11 (1) , 4157-4168
Dynamic Modeling and Analysis of Vehicle-Track–Bridge Coupled System for Superconducting EDS Train
The superconducting electrodynamic suspension (EDS) train is the only high-speed manned transportation system that can reach 600 km/h, bringing into focus on its dynamic performance and ride quality in recent years. However, there has been little research that elucidated the coupling mechanisms among the vehicle, track and bridge, which makes the accurate characterization and reliable evaluation of dynamic performance difficult. In this paper, the 66 degree-of-freedom (DOF) numerical dynamic model of the EDS train is built. Afterwards, electromagnetic forces are calculated and the relationship among the electromagnetic forces and the attitude of superconducting magnet (SCM) unit is described with the Response Surface Method (RSM) and its reliability is validated. Subsequently, the numerical model of the bridge is established. Using electromagnetic forces to connect vehicle and bridge, the vehicle-track-bridge coupled EDS system was eventually built. By means of these, the results illustrate that the resonance occurs mainly in the range of 350 km/h to 400 km/h and benefits from the weak coupled relationship between vehicle and bridge, the coupled vibration is not prominent. These results confirm the potential of EDS in high-speed transit field and a useful reference is provided for its engineering application.
- 29 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (4) , 1-10
Partial Force Calculation and Structural Strength Analysis of Null-Flux Coil for Superconducting Electrodynamic Suspension Train
The superconducting electrodynamic suspension train has advantages such as a large suspension gap and a high lift-to-drag ratio. Its ground coils are made of ironless hollow windings laid along the track. Due to the strong magnetic field generated by the onboard superconducting magnets, the train exerts instant and intense stress on the coils when passing through. This article proposed four kinds of track coils with different fixed structures, and investigated the structural strength by an analytical-simulation coupling analysis method. First, the 3-D electromagnetic force distribution model of the actual track coil was established, and the load distribution of each coil was accurately characterized. Then, four kinds of fixed methods of the track coil were proposed and their mode analysis was carried out. Subsequently, the loading capacity of four kinds of track coils under extreme stress load was studied by static loading analysis. Finally, through the transient stress analysis, the stress variation of four kinds of track coils during the actual operation was investigated.
- 29 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (4) , 1-10
Partial Force Calculation and Structural Strength Analysis of Null-Flux Coil for Superconducting Electrodynamic Suspension Train
The superconducting electrodynamic suspension train has advantages such as a large suspension gap and a high lift-to-drag ratio. Its ground coils are made of ironless hollow windings laid along the track. Due to the strong magnetic field generated by the onboard superconducting magnets, the train exerts instant and intense stress on the coils when passing through. This article proposed four kinds of track coils with different fixed structures, and investigated the structural strength by an analytical-simulation coupling analysis method. First, the 3-D electromagnetic force distribution model of the actual track coil was established, and the load distribution of each coil was accurately characterized. Then, four kinds of fixed methods of the track coil were proposed and their mode analysis was carried out. Subsequently, the loading capacity of four kinds of track coils under extreme stress load was studied by static loading analysis. Finally, through the transient stress analysis, the stress variation of four kinds of track coils during the actual operation was investigated.