BNBehnam Nikmaram

Behnam Nikmaram

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Behnam Nikmaram has a total of 15 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Predictive Power Control based on Ultralocal PQ Theory for Power Sharing of Grid-Following Inverter in Microgrids

    by Mahdi S. Mousavi, Behnam Nikmaram, Moslem Dehghani, Mokhtar Aly, S. Alireza Davari, Freddy Flores-Bahamonde, Jose Rodriguez

    Grid-following inverters (GFLs) are generally responsible for active and reactive power (PQ) control in microgrids, while grid-forming inverters (GFMs) regulate voltage and frequency. Hence, power control approaches such as predictive power control (PPC), which typically employ the instantaneous power theory based on the microgrid’s model, are applied to GFLs. To reduce this model dependency, this article presents a novel PPC using the newly defined ultralocal PQ theory for the GFLs. This method utilizes the voltages of two nodes to predict the PQ of the microgrid without having the exact model of the system. Moreover, a fractional-order disturbance observer (FODO) is presented to identify and compensate for power disturbances in real time. The proposed approach is validated on an experimental leader-follower microgrid test bench. The method achieves lower power ripples and reduced total current harmonic distortion compared with the conventional model predictive control. So, the effectiveness of the proposed PPC for power sharing of the microgrid is verified in various test conditions.

  • Indirect Predictive Power Control of Grid-Following Inverters Using the Grid-Side Measurements

    by Mahdi S. Mousavi, Behnam Nikmaram, Mokhtar Aly, S. Alireza Davari, Jose Rodriguez

    The grid-following inverters (GFLs) in microgrids require active and reactive power control. While the predictive power control (PPC) has shown effective performance due to its flexibility and fast response, it needs the system model and measured signals of the inverter and load. The high numbers of sensors and model dependency reduce the reliability of the PPC. To address these issues, this article proposes two PPC schemes, referred to as direct and indirect PPCs. The direct PPC utilizes the ultralocal model theory to reduce the parameter dependency of the prediction algorithm. Thus, novel models for predicting active and reactive power are presented here. To further increase the system reliability, an indirect PPC is presented, which employs the grid-side current measurements to control the active and reactive power. This reduces the number of sensors required in the direct PPC, which requires the GFL and load measurements. The results have shown that the GFL control system can be switched between the indirect and direct PPC modes promptly. This feature is useful when the sensors are faulty or need maintenance. Both proposed control methods have been verified using an experimental setup and compared with the model-based PPC. The results confirm the improved performance of the proposed PPCs and easy transitions between them.

  • Sensorless Model-Free Predictive Control of Permanent Magnet Synchronous Motor

    by S. Alireza Davari, Mahdi S. Mousavi, Behnam Nikmaram, Freddy Flores-Bahamonde, Fengxinag Wang, Patrick Wheeler, Jose Rodriguez

    Model-free predictive control has demonstrated robust performance while maintaining the benefits of predictive control, including precision and rapid transient response. This technique has recently been successfully investigated to control permanent magnet synchronous motors. Thus, it is time to study the implementation of model-free control in advanced motor drives, such as sensorless drives. This article proposes a sensorless model-free predictive control for permanent magnet motor drives. The proposed method uses an ultralocal model to estimate back electromotive force and utilizes the same model for predicting current. The local parameters of the model are adjusted using the infinity norm technique to ensure the robustness of the control law. The validity of the proposed method is confirmed through experimental results.


  • Applying Model-Free Predictive Current Control With Parallel Cost Functions for Open-End Winding Synchronous Reluctance Motor

    by Mahdi S. Mousavi, Behnam Nikmaram, Abolfazl Nassaji, S. Alireza Davari, Freddy Flores-Bahamonde, Jose Rodriguez

    This article presents a model-free predictive current control (MFPCC) with parallel cost functions for the common dc-link dual-inverter-fed open-end winding synchronous reluctance motor (OW-SynRM). The MFPCC has a general prediction algorithm that can be implemented in any reference frame. Using this feature, and the fact that each winding of the OW-SynRM is supplied separately by two legs of the dual inverter, the current predictions are achieved independently for each phase in the Cartesian coordinates. Then, three parallel cost functions are defined for three predicted phase currents. Thus, the finite control-set approach is utilized separately for each phase to determine the switching state of the dual inverter. In addition, an adaptive proportional-resonant extended state observer (PR-ESO) is introduced to improve the current predictions regarding the operating frequency of the motor. The proposed MFPCC for OW-SynRM has several advantages. First, the computational burden is decreased significantly because the prediction algorithm utilizes fewer candidates in the Cartesian coordinates. In addition, the weighting factor is not required due to using independent cost functions. Furthermore, the zero sequence current is automatically adjusted without a controller. Finally, the PR-ESO-based model-free approach improves the current predictions of the proposed method. The proposed MFPCC of the OW-SynRM is evaluated using the experimental results.


  • Full-Cycle Iterative Observer: A Comprehensive Approach for Position Estimation in Sensorless Predictive Control of SynRM

    by Behnam Nikmaram, Mahdi S. Mousavi, S. Alireza Davari, Freddy Flores-Bahamonde, Patrick Wheeler, Jose Rodriguez, Mehdi Fazeli

    This article presents a new iteration algorithm for the position estimation of synchronous reluctance motors by unifying the active flux observer and Newton-Raphson algorithm. Thus, a full-cycle iterative observer is derived, in which the active flux is estimated in each iteration of the Newton-Raphson technique. Hence, the dependency of the active flux to the position is considered in the Newton-Raphson formula. This guarantees the accurate convergence of the position. Furthermore, the stator flux observer is enhanced with nonlinear feedback to attain a robust sensorless control scheme, compensating for the stator resistance mismatch. The experimental results confirm the superior performance and improved robustness of the proposed sensorless technique compared to the standard Newton-Raphson-based sensorless control method.


  • Adaptive-Based Accurate Rotor Initial Position Estimation in Synchronous Reluctance Motors

    by Hamidreza Pairo, Behnam Nikmaram, Sobhan Mohamadian

    Accurate estimation of initial rotor position is of importance in synchronous reluctance motor (SynRM) drives to gain maximum starting torque and to prevent the overcurrent fault and reverse rotation. This article presents an accurate algorithm, subsumed under the category of voltage pulse injection methods, to define the rotor initial position. In this method, first, the rotor initial sector (with a resolution of 30 electrical degrees) is estimated according to the peak currents acquired by the injection of the symmetrical pulses. Then, the data of an optimum switching vector are introduced to an adaptive-based algorithm to result in the lowest possible error. The efficacy of the proposed method is checked experimentally on a 0.5-hp SynRM drive system and the accuracy of the method is proven high against two other practical pulse-injection-based methods, i.e., conventional and iterative pulse injection-based methods. In addition, experimental results of the high-frequency square-wave method prove the higher accuracy and faster estimation time of the proposed method. The implementation of the proposed method is simple and straightforward. Furthermore, it is robust to the variations and uncertainties of the stator resistance.


  • Predictive Torque Control Using a Simplified Algorithm to Maximize Adhesion Force in Railway Applications

    by Amin Hassanzadeh, Ali Akbar Emarloo, Behnam Nikmaram, Mehdi Fazeli

    In this paper, a novel methodology is presented in which the adhesion phenomenon between the wheels of a train and rails maintains its maximum value during train traction and braking mode with the help of continuous prediction of wheel slip. The best operation point in which the maximum acceleration at the maximum adhesion point is preserved is obtained in the whole running time. Due to being an unmeasurable parameter, an estimator is also employed to estimate adhesion coefficient value steadily. Different parameters affect the curve of the adhesion coefficient versus the wheel slip and make it a non-fixed curve. the proposed method also has the ability to estimate this curve and find the best operating point in all conditions. The outcome of the proposed control is the reference torque which is the input of the induction traction motor controller. The suitable behavior of the induction motor is a staple factor in the effectiveness of the presented method. Due to simplicity, not using the current PI controller, and a satisfactory performance, a predictive torque controller with delay compensation is employed to regulate the reference torque. The simulation results verify that the proposed algorithm has a befitting performance.