Yabin An
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Yabin An has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Xiaoming Li
Xidian University
3 shared publications - Bin Jiang
School of Microelectronics, Xidian University, Xi’an 710071, China
1 shared publication - Hao Yang
School of Microelectronics, Xidian University, Xi’an 710126, China
1 shared publication - Hui Xu
School of Microelectronics, Xidian University, Xi’an 710071, China
1 shared publication - Xinkai Zhen
School of Microelectronics, Xidian University, Xi’an 710126, China
1 shared publication - Xiting Feng
School of Microelectronics, Xidian University, Xi’an 710071, China
1 shared publication
Latest Publications
- Open Access
- 28 January 2026
- Published by MDPI AG in Micromachines
- Vol. 17 (2) , 178
Design of a Nanowatt-Level-Power-Consumption, High-Sensitivity Wake-Up Receiver for Wireless Sensor Networks
This paper addresses the core conflict between long-range communication and ultra-low power requirements in sensing nodes for Wireless Sensor Networks (WSNs) by proposing a wake-up receiver (WuRx) design featuring nanowatt-level power consumption and high sensitivity. Conventional architectures are plagued by low energy efficiency, poor demodulation reliability, and insufficient clock synchronization accuracy, which hinders their practical application in real-world scenarios like WSNs. The proposed design employs an event-triggered mechanism, where a continuously operating, low-power WuRx monitors the channel and activates the main system only after validating a legitimate command, thereby significantly reducing standby power. At the system design level, a key innovation is direct conjugate matching between the antenna and a multi-stage rectifier, replacing the traditional 50 Ohm interface, which substantially improves energy transmission efficiency. Furthermore, a mean-detection demodulation circuit is introduced to dynamically generate an adaptive reference level, effectively overcoming the challenge of discriminating shallow modulation caused by signal saturation in the near-field region. At the baseband processing level, a configurable fault-tolerant correlator logic and a data-edge-triggered clock synchronization circuit are designed, combined with oversampling techniques to suppress clock drift and enhance the reliability of long data packet reception. Fabricated in a TSMC 0.18 µm CMOS process, the receiver features an ultra-low power consumption of 305 nW at 0.5 V and a high sensitivity of −47 dBm, enabling a communication range of up to 400 m in the 920–925 MHz band. Through synergistic innovation at both the circuit and system levels, this research provides a high-efficiency, high-reliability wake-up solution for long-range WSN nodes, effectively promoting the large-scale application of WSN technology in practical deployments.
- 28 January 2026
- Published by MDPI AG in Micromachines
- Vol. 17 (2) , 178
Open AccessDesign of a Nanowatt-Level-Power-Consumption, High-Sensitivity Wake-Up Receiver for Wireless Sensor Networks
This paper addresses the core conflict between long-range communication and ultra-low power requirements in sensing nodes for Wireless Sensor Networks (WSNs) by proposing a wake-up receiver (WuRx) design featuring nanowatt-level power consumption and high sensitivity. Conventional architectures are plagued by low energy efficiency, poor demodulation reliability, and insufficient clock synchronization accuracy, which hinders their practical application in real-world scenarios like WSNs. The proposed design employs an event-triggered mechanism, where a continuously operating, low-power WuRx monitors the channel and activates the main system only after validating a legitimate command, thereby significantly reducing standby power. At the system design level, a key innovation is direct conjugate matching between the antenna and a multi-stage rectifier, replacing the traditional 50 Ohm interface, which substantially improves energy transmission efficiency. Furthermore, a mean-detection demodulation circuit is introduced to dynamically generate an adaptive reference level, effectively overcoming the challenge of discriminating shallow modulation caused by signal saturation in the near-field region. At the baseband processing level, a configurable fault-tolerant correlator logic and a data-edge-triggered clock synchronization circuit are designed, combined with oversampling techniques to suppress clock drift and enhance the reliability of long data packet reception. Fabricated in a TSMC 0.18 µm CMOS process, the receiver features an ultra-low power consumption of 305 nW at 0.5 V and a high sensitivity of −47 dBm, enabling a communication range of up to 400 m in the 920–925 MHz band. Through synergistic innovation at both the circuit and system levels, this research provides a high-efficiency, high-reliability wake-up solution for long-range WSN nodes, effectively promoting the large-scale application of WSN technology in practical deployments.
- Open Access
- 16 March 2024
- Published by MDPI AG in Electronics
- Vol. 13 (6) , 1094
A 0.59 nW/kHz Clock Circuit with High-Precision Clock Calibration for Passive Internet of Things Chips
The high precision and low power consumption of the clock generator are critical in passive RFID transponders and passive IoT chips, but fluctuations in PVT can cause considerable degradation in the precision of the chip’s internal clocks. This paper proposes a high-precision clock circuit with a single-shot calibration method to addresses this issue in a low-power clock solution. Based on the reference timespan in the preamble of the down-link RF envelope, a TDIF (Time-digital to current-frequency) calibration method was implemented with both a streamlined procedure and customized circuits. By computing the difference between the time counts and applying it to an ultra-low-power, current-starved oscillator, the current change ratio can be linearly controlled. Compared to the traditional integer frequency division scheme used by passive tags for a 160 k bits up-link data rate, the required frequency for the clock generator was reduced from 960 kHz to 320 kHz, the calibration error was reduced from ±10% to ±3% for ±25% frequency deviation, the calibration time was 133.3 μs for a single shot in this work, and the power consumption was 158 nW after the calibration was completed. This leads to an excellent power efficiency of 0.59 nW/kHz and meets the requirements of low power, low cost, and PVT robustness in the RF-powered passive IoT chips. By appropriately increasing the number of calibration digits and the duration, this calibration approach could also be used for other ultra-low-power passive IoT chips that require higher-precision clocking without the use of off-chip crystals.
- 16 March 2024
- Published by MDPI AG in Electronics
- Vol. 13 (6) , 1094
Open AccessA 0.59 nW/kHz Clock Circuit with High-Precision Clock Calibration for Passive Internet of Things Chips
The high precision and low power consumption of the clock generator are critical in passive RFID transponders and passive IoT chips, but fluctuations in PVT can cause considerable degradation in the precision of the chip’s internal clocks. This paper proposes a high-precision clock circuit with a single-shot calibration method to addresses this issue in a low-power clock solution. Based on the reference timespan in the preamble of the down-link RF envelope, a TDIF (Time-digital to current-frequency) calibration method was implemented with both a streamlined procedure and customized circuits. By computing the difference between the time counts and applying it to an ultra-low-power, current-starved oscillator, the current change ratio can be linearly controlled. Compared to the traditional integer frequency division scheme used by passive tags for a 160 k bits up-link data rate, the required frequency for the clock generator was reduced from 960 kHz to 320 kHz, the calibration error was reduced from ±10% to ±3% for ±25% frequency deviation, the calibration time was 133.3 μs for a single shot in this work, and the power consumption was 158 nW after the calibration was completed. This leads to an excellent power efficiency of 0.59 nW/kHz and meets the requirements of low power, low cost, and PVT robustness in the RF-powered passive IoT chips. By appropriately increasing the number of calibration digits and the duration, this calibration approach could also be used for other ultra-low-power passive IoT chips that require higher-precision clocking without the use of off-chip crystals.
- Open Access
- 1 March 2024
- Published by MDPI AG in Electronics
- Vol. 13 (5) , 961
A BLE 5.0 Extended Advertising Backscatter with Commodity Devices in Passive IoT Scenarios
BLE-based (Bluetooth Low Energy-based) backscatter has received considerable attention, as it aims to communicate with everyday smart devices such as smartphones, smartwatches, and tablets in passive IoT. The state-of-the-art BLE backscatter systems enable communication using a specialized continuous wave (CW) generator or entirely using commodity BLE 4.0 radios as an RF source. However, the existing BLE communication systems suffer from several key issues, including a short carrier length and a large frequency shift. This paper presents a passive BLE (PBLE) backscatter communication system that utilizes commodity BLE 5.0 radios. The system uses a BLE 5.0 extended advertising packet with partial single tones as excitations transmitting on the secondary advertising channel of BLE 5.0, and the BLE backscatter tag produces bandpass frequency-shift keying modulation at 1 Mb/s, which enables compatibility with BLE advertising channels. The prototype is implemented using an NRF52832 BLE 5.0 commodity chip, smart devices, and tags with FPGAS and chips. In FPGA board-level verification, when the downlink distance is 0.5 m, the uplink distance can reach 10 m. In chip testing, the uplink distance can reach 7 m when the downlink distance is 1 m. The baseband power consumption is 2 μW, with a total power consumption of 10 μW. This system eliminates the need for expensive and costly specialized RF sources, unlike the BLE backscatter communication system that uses a specialized CW generator. Compared to the BLE backscatter communication system that uses commodity BLE 4.0 radios, this system reduces the minimum frequency shift from 24 MHz to 2 MHz and increases the length of the single tones as a CW by a factor of about seven, from 31 bytes to 254 bytes.
- 1 March 2024
- Published by MDPI AG in Electronics
- Vol. 13 (5) , 961
Open AccessA BLE 5.0 Extended Advertising Backscatter with Commodity Devices in Passive IoT Scenarios
BLE-based (Bluetooth Low Energy-based) backscatter has received considerable attention, as it aims to communicate with everyday smart devices such as smartphones, smartwatches, and tablets in passive IoT. The state-of-the-art BLE backscatter systems enable communication using a specialized continuous wave (CW) generator or entirely using commodity BLE 4.0 radios as an RF source. However, the existing BLE communication systems suffer from several key issues, including a short carrier length and a large frequency shift. This paper presents a passive BLE (PBLE) backscatter communication system that utilizes commodity BLE 5.0 radios. The system uses a BLE 5.0 extended advertising packet with partial single tones as excitations transmitting on the secondary advertising channel of BLE 5.0, and the BLE backscatter tag produces bandpass frequency-shift keying modulation at 1 Mb/s, which enables compatibility with BLE advertising channels. The prototype is implemented using an NRF52832 BLE 5.0 commodity chip, smart devices, and tags with FPGAS and chips. In FPGA board-level verification, when the downlink distance is 0.5 m, the uplink distance can reach 10 m. In chip testing, the uplink distance can reach 7 m when the downlink distance is 1 m. The baseband power consumption is 2 μW, with a total power consumption of 10 μW. This system eliminates the need for expensive and costly specialized RF sources, unlike the BLE backscatter communication system that uses a specialized CW generator. Compared to the BLE backscatter communication system that uses commodity BLE 4.0 radios, this system reduces the minimum frequency shift from 24 MHz to 2 MHz and increases the length of the single tones as a CW by a factor of about seven, from 31 bytes to 254 bytes.