A. Ashraf Ghandour
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
A. Ashraf Ghandour has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
A. I. Selmy
Department of Mechanical Design and Production Engineering, Faculty of Engineering Zagazig University Zagazig Egypt
2 shared publicationsA. M. Kabeel
Department of Mechanical Design and Production Engineering, Faculty of Engineering Zagazig University Zagazig Egypt
2 shared publicationsAhmed Ibrahim
Department of Mechanical Design and Production Engineering, Faculty of Engineering Zagazig University Zagazig Egypt
2 shared publicationsM. Megahed
Department of Mechanical Design and Production Engineering, Faculty of Engineering, Zagazig University, P.O. Box 44519, Zagazig, Egypt
2 shared publicationsAbdel-Halim S. Salem Said
Department of Mechanical and Materials Engineering, University of Jeddah, Jeddah, 21959, Kingdom of Saudi Arabia
1 shared publicationAbdessalem Jarraya
Department of Mechanical and Materials Engineering, University of Jeddah, Jeddah, 21959, Kingdom of Saudi Arabia
1 shared publication
Latest Publications
- Open Access
- 12 June 2026
- Published by Springer Nature in Scientific Reports
- Vol. 16 (1)
Advanced hybrid nanocomposites for infrastructure renewal: enhanced shear and flexural performance in load-bearing applications
Glass fiber-reinforced polymer composites (GFRP) are widely used in engineering applications thanks to their high performance. This research investigates how various hybrid reinforcement techniques influence the flexural and shear performance of GFRP laminates. The composite materials were produced by integrating nonwoven glass tissues with woven glass fabrics, along with single and hybrid nanoscale fillers. Silica (SiO₂) and carbon (C) nanoparticles at different weight fractions were selected as nano-reinforcements for their cost-effectiveness. Seven composite variants were made by hand lay-up, including an unmodified GFRP reference and six hybrid configurations. Sonication and magnetic stirring methods were used to disperse nanoparticles in the epoxy matrix uniformly. Flexural performance was assessed by the three-point flexural test, while shear performance was assessed using the short beam shear and Iosipescu tests to measure both in-plane and interlaminar shear strength. When compared to the unmodified GFRP reference, samples with 0.5 wt% carbon black showed better shear and flexural performance. Hybrid reinforcement using 0.25 wt% carbon black combined with 0.25 wt% silica achieved the highest flexural strain increase (21%) and an 8% gain in flexural strength. This indicates improved ductility without compromising shear performance. However, higher concentrations of hybrid fillers negatively affect mechanical behavior.
- 12 June 2026
- Published by Springer Nature in Scientific Reports
- Vol. 16 (1)
Open AccessAdvanced hybrid nanocomposites for infrastructure renewal: enhanced shear and flexural performance in load-bearing applications
Glass fiber-reinforced polymer composites (GFRP) are widely used in engineering applications thanks to their high performance. This research investigates how various hybrid reinforcement techniques influence the flexural and shear performance of GFRP laminates. The composite materials were produced by integrating nonwoven glass tissues with woven glass fabrics, along with single and hybrid nanoscale fillers. Silica (SiO₂) and carbon (C) nanoparticles at different weight fractions were selected as nano-reinforcements for their cost-effectiveness. Seven composite variants were made by hand lay-up, including an unmodified GFRP reference and six hybrid configurations. Sonication and magnetic stirring methods were used to disperse nanoparticles in the epoxy matrix uniformly. Flexural performance was assessed by the three-point flexural test, while shear performance was assessed using the short beam shear and Iosipescu tests to measure both in-plane and interlaminar shear strength. When compared to the unmodified GFRP reference, samples with 0.5 wt% carbon black showed better shear and flexural performance. Hybrid reinforcement using 0.25 wt% carbon black combined with 0.25 wt% silica achieved the highest flexural strain increase (21%) and an 8% gain in flexural strength. This indicates improved ductility without compromising shear performance. However, higher concentrations of hybrid fillers negatively affect mechanical behavior.
- 15 December 2024
- Published by Wiley in Polymer Composites
- Vol. 46 (7) , 6670-6680
Performance analysis of 3D orthogonal polymeric composites reinforced with metallic and glass fibrous z‐binders of varying sizes
Despite the wide use of three‐dimensional (3D) woven composites in different applications, their production is often costly. This study explores cost‐effective 3D orthogonal woven polymer composites to enhance mechanical performance. Four 3D composite variants, each incorporating different volumes of z‐binders (copper wires or glass fibers), were compared to a 2D woven composite. All composites were produced using a simple, economical hand lay‐up method. Wear resistance, in‐plane shear strength, and impact strength were assessed. Results indicated that all 3D composites surpassed the 2D composite in impact strength, especially those reinforced with glass fiber z‐binders. The single glass fiber z‐binder composite exhibited the highest impact strength increase (20.6%). Most 3D composites showed slightly reduced in‐plane shear strength compared to the 2D composite, with the smallest decrease (1.68%) observed in specimens with a small copper z‐binder. Notably, all 3D composites demonstrated superior wear resistance to 2D counterparts under various loads. Glass fiber z‐binder reinforcements outperformed copper z‐binders, with double fiber z‐binders yielding the maximum wear resistance enhancement. These findings underscore the potential of 3D woven composites for applications demanding high impact and wear resistance, such as automotive, structural components, and sports equipment.Highlights: 3D woven composites are widely used in various engineering applications. Limited studies explore the in‐plane shear and wear behavior of 3D composites. Copper and glass fiber z‐binders were used in manufacturing 3D woven composites. The used hand lay‐up method reduces manufacturing costs. 3D woven composites improve impact and wear resistance compared to 2D ones.
- 15 December 2024
- Published by Wiley in Polymer Composites
- Vol. 46 (7) , 6670-6680
Performance analysis of 3D orthogonal polymeric composites reinforced with metallic and glass fibrous z‐binders of varying sizes
Despite the wide use of three‐dimensional (3D) woven composites in different applications, their production is often costly. This study explores cost‐effective 3D orthogonal woven polymer composites to enhance mechanical performance. Four 3D composite variants, each incorporating different volumes of z‐binders (copper wires or glass fibers), were compared to a 2D woven composite. All composites were produced using a simple, economical hand lay‐up method. Wear resistance, in‐plane shear strength, and impact strength were assessed. Results indicated that all 3D composites surpassed the 2D composite in impact strength, especially those reinforced with glass fiber z‐binders. The single glass fiber z‐binder composite exhibited the highest impact strength increase (20.6%). Most 3D composites showed slightly reduced in‐plane shear strength compared to the 2D composite, with the smallest decrease (1.68%) observed in specimens with a small copper z‐binder. Notably, all 3D composites demonstrated superior wear resistance to 2D counterparts under various loads. Glass fiber z‐binder reinforcements outperformed copper z‐binders, with double fiber z‐binders yielding the maximum wear resistance enhancement. These findings underscore the potential of 3D woven composites for applications demanding high impact and wear resistance, such as automotive, structural components, and sports equipment.Highlights: 3D woven composites are widely used in various engineering applications. Limited studies explore the in‐plane shear and wear behavior of 3D composites. Copper and glass fiber z‐binders were used in manufacturing 3D woven composites. The used hand lay‐up method reduces manufacturing costs. 3D woven composites improve impact and wear resistance compared to 2D ones.
- Open Access
- 2 March 2024
- Published by Springer Nature in Fibers and Polymers
- Vol. 25 (4) , 1417-1428
The Influence of Glass Fiber and Copper Wire z-Binder on the Mechanical Properties of 3D Woven Polymeric Composites
Three-dimensional composites (3D) have potential applications in various fields due to their enhanced properties compared to conventional two-dimensional composites (2D). This study investigates the effect of different volumes of z-binder made from copper wire and E-glass fiber on the mechanical properties of 3D woven polymeric composites. The tensile, flexural, and fracture toughness behavior of four types of 3D orthogonal woven composites were studied in addition to a comparative 2D composite. The creation of the 3D orthogonal single-ply fabrics involved weaving z-binders using two different copper wire diameters, single fiber bundles, and double fiber bundles, each combined with four layers of woven E-glass fiber. The consolidation process for both 2D fabric and single-fabric 3D woven composites was executed using the hand lay-up technique. The results showed that most 3D woven composites outperformed 2D composites in terms of fracture toughness (stress intensity factor KIC and energy release rate GIC) and flexural strain. However, a decrease in flexural strength and tensile properties was observed for all 3D composites. The specimen with a small copper diameter had the smallest decrease of 5% in tensile strength. Furthermore, a decrease of 9% and 21% was attained by reinforcing with double and single glass fiber bundle z-binders, respectively, as compared with 2D composites. The highest enhancement of 92.5% in flexural failure strain was attained with double glass fiber bundles of z-binder. The maximum improvement in KIC fracture toughness, reaching 126% and 101.5%, was observed in specimens with a single glass fiber bundle z-binder and those with a large copper wire diameter, respectively.
- 2 March 2024
- Published by Springer Nature in Fibers and Polymers
- Vol. 25 (4) , 1417-1428
Open AccessThe Influence of Glass Fiber and Copper Wire z-Binder on the Mechanical Properties of 3D Woven Polymeric Composites
Three-dimensional composites (3D) have potential applications in various fields due to their enhanced properties compared to conventional two-dimensional composites (2D). This study investigates the effect of different volumes of z-binder made from copper wire and E-glass fiber on the mechanical properties of 3D woven polymeric composites. The tensile, flexural, and fracture toughness behavior of four types of 3D orthogonal woven composites were studied in addition to a comparative 2D composite. The creation of the 3D orthogonal single-ply fabrics involved weaving z-binders using two different copper wire diameters, single fiber bundles, and double fiber bundles, each combined with four layers of woven E-glass fiber. The consolidation process for both 2D fabric and single-fabric 3D woven composites was executed using the hand lay-up technique. The results showed that most 3D woven composites outperformed 2D composites in terms of fracture toughness (stress intensity factor KIC and energy release rate GIC) and flexural strain. However, a decrease in flexural strength and tensile properties was observed for all 3D composites. The specimen with a small copper diameter had the smallest decrease of 5% in tensile strength. Furthermore, a decrease of 9% and 21% was attained by reinforcing with double and single glass fiber bundle z-binders, respectively, as compared with 2D composites. The highest enhancement of 92.5% in flexural failure strain was attained with double glass fiber bundles of z-binder. The maximum improvement in KIC fracture toughness, reaching 126% and 101.5%, was observed in specimens with a single glass fiber bundle z-binder and those with a large copper wire diameter, respectively.