Manuel González-Gallego
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Manuel González-Gallego has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Félix Terroba Ramírez
Escuela Politécnica Superior, Alfonso X el Sabio University (UAX), 28691 Madrid, Spain
2 shared publications - Juan Jose´ Lo´pez Cela
Instituto de Investigaciones Energéticas y Aplicaciones Industriales, Escuela Técnica Superior de Ingeniería Industrial de Ciudad Real, Universidad de Castilla-La Mancha, Av. Camilo José Cela s/n, 13071 Ciudad Real, Spain
2 shared publications - Juan Luis Martínez Vicente
Instituto de Investigaciones Energéticas y Aplicaciones Industriales, Escuela Técnica Superior de Ingeniería Industrial de Ciudad Real, Universidad de Castilla-La Mancha, Av. Camilo José Cela s/n, 13071 Ciudad Real, Spain
2 shared publications - Malte Frövel
Instituto Nacional de Tecnica Aeroespacial
2 shared publications - Miguel González del Val
Materials and Structures Department, Instituto Nacional de Técnica Aeroespacial, Crta. de Ajalvir km 4, 28850 Torrejon de Ardoz, Madrid, Spain
2 shared publications
Latest Publications
- Open Access
Fiber Bragg Gratings Sensor Strain–Optic Behavior with Different Polymeric Coatings Subjected to Transverse Strain
This research work is based on a previous study by the authors that characterized the behavior of FBG sensors with a polyimide coating in a structural monitoring system. Sensors applied to structural health monitoring are affected by the presence of simultaneous multidirectional strains. The previous study observed the influence of the transverse strain () while keeping the longitudinal strain constant (), where the x direction is the direction of the optical fiber. The present study develops an experimental methodology consisting of a biaxial test plan on cruciform specimens with three embedded FBG sensors coated with polyimide, acrylate, and ORMOCER®. Applying the Strain–Optic Theory as a reference, a comparison of the experimental values obtained with the different coatings was studied. This experimental work made it possible to study the influence of the transverse strain () on the longitudinal measurements of each FBGS and the influence of the coating material. Finally, the calibration procedure was defined as well as (strain sensitivity factor) for each sensor.Open AccessFiber Bragg Gratings Sensor Strain–Optic Behavior with Different Polymeric Coatings Subjected to Transverse Strain
This research work is based on a previous study by the authors that characterized the behavior of FBG sensors with a polyimide coating in a structural monitoring system. Sensors applied to structural health monitoring are affected by the presence of simultaneous multidirectional strains. The previous study observed the influence of the transverse strain () while keeping the longitudinal strain constant (), where the x direction is the direction of the optical fiber. The present study develops an experimental methodology consisting of a biaxial test plan on cruciform specimens with three embedded FBG sensors coated with polyimide, acrylate, and ORMOCER®. Applying the Strain–Optic Theory as a reference, a comparison of the experimental values obtained with the different coatings was studied. This experimental work made it possible to study the influence of the transverse strain () on the longitudinal measurements of each FBGS and the influence of the coating material. Finally, the calibration procedure was defined as well as (strain sensitivity factor) for each sensor. - Open Access
- 4 March 2024
- Published by MDPI AG in Preprints.org
FBGS Strain–Optic Behavior with Different Polymeric Coatings Subject to Transverse Strain
This research work has been based on a previous study by the authors that characterized the behavior of a polyimide-coated FBG sensor in a structural monitoring system. Sensors applied to structural health monitoring are affected in the presence of a state of multidirectional strains simultaneously. The previous study observed the influence of transverse strain (ε_y) while keeping longitudinal strain constant (ε_x), where the direction x is the direction of the optical fiber. The present study developed an experimental methodology which has consisted of carrying out a campaign of biaxial tests on cruciform specimens with three embedded FBG sensors coated with polyimide, acrylate and ORMOCER®. Applying the Strain–Optic Theory as reference, a comparison of the results obtained with the different coatings has been studied. This experimental work has done it possible to study the influence of transverse strain (ε_y) in the longitudinal measurement of each of the FBG sensor and the influence of the coating material. Finally, the calibration procedure as well as the strain sensitivity factor K for each sensor has been defined.
- 4 March 2024
- Published by MDPI AG in Preprints.org
Open AccessFBGS Strain–Optic Behavior with Different Polymeric Coatings Subject to Transverse Strain
This research work has been based on a previous study by the authors that characterized the behavior of a polyimide-coated FBG sensor in a structural monitoring system. Sensors applied to structural health monitoring are affected in the presence of a state of multidirectional strains simultaneously. The previous study observed the influence of transverse strain (ε_y) while keeping longitudinal strain constant (ε_x), where the direction x is the direction of the optical fiber. The present study developed an experimental methodology which has consisted of carrying out a campaign of biaxial tests on cruciform specimens with three embedded FBG sensors coated with polyimide, acrylate and ORMOCER®. Applying the Strain–Optic Theory as reference, a comparison of the results obtained with the different coatings has been studied. This experimental work has done it possible to study the influence of transverse strain (ε_y) in the longitudinal measurement of each of the FBG sensor and the influence of the coating material. Finally, the calibration procedure as well as the strain sensitivity factor K for each sensor has been defined.