Yelim Kang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Yelim Kang has a total of 37 co-authors. Here are the top co-authors by number of shared publications:
- Jae Won Shim
School of Electrical Engineering, Korea University, Seoul, Republic of Korea
3 shared publications Tae Hyuk Kim
School of Electrical Engineering, Korea University, Seoul, Republic of Korea
3 shared publicationsGyeong Min Lee
School of Electrical Engineering, Korea University, Seoul, Republic of Korea
2 shared publications- Han Young Woo
Department of Chemistry, Korea University, Seoul, Republic of Korea
2 shared publications Seon Joong Kim
School of Electrical Engineering, Korea University, Seoul, Republic of Korea
2 shared publications- Bo Ram Lee
School of Advanced Materials Science and Engineering Sungkyunkwan University (SKKU) Suwon Republic of Korea
1 shared publication
Latest Publications
- 4 November 2026
- Published by Springer Nature in Nature
- Vol. 659 (8139) , 49-57
Accelerating commercialization and deployment of indoor photovoltaics
- 4 November 2026
- Published by Springer Nature in Nature
- Vol. 659 (8139) , 49-57
Accelerating commercialization and deployment of indoor photovoltaics
- Open Access
- 12 September 2026
- Published by Wiley in Advanced Functional Materials
- Vol. 36 (85)
Oligoethylene Glycol Side‐Chain Engineering of Y6‐Derived Nonfullerene Acceptors for Thermally Induced Spontaneous Pseudo‐Planar Heterojunction Organic Photodetectors
Dark current density ( J D ) fundamentally limits the noise characteristics and detectivity of organic photodetectors (OPDs), arising primarily from reverse‐bias carrier injection and trap‐mediated leakage pathways in donor‐acceptor (D‐A) bulk‐heterojunction (BHJ) active layers. Although pseudo‐planar heterojunction ( p ‐PHJ) architectures effectively suppress these losses, their implementation often requires complex layer engineering or controlled processing conditions. Here, we report two Y6‐derived nonfullerene acceptors (NFAs), YTEG‐4F and YTEG‐4Cl, bearing hydrophilic oligoethylene glycol (OEG) side chains that induce thermally driven spontaneous vertical phase separation within the D‐A BHJ layer. This molecular modification enables p‐PHJ formation, suppressing reverse‐bias carrier injection and leakage pathways, thereby reducing J D . In contrast to the thermally annealed PM6:Y6 device, which exhibits an increased J D of 6.64 × 10 −7 A cm −2 , the PM6:YTEG‐4F and PM6:YTEG‐4Cl devices achieve low J D s of 2.76 × 10 −9 and 3.24 × 10 −9 A cm −2 , corresponding to approximately 260‐fold and 210‐fold reductions after thermal annealing, respectively. Consequently, shot‐noise‐limited detectivities ( D sh *) of 1.17 × 10 13 and 9.74 × 10 12 Jones are achieved at −0.5 V for PM6:YTEG‐4F and PM6:YTEG‐4Cl p ‐PHJ OPDs, respectively. This work demonstrates that OEG side‐chain engineering of NFAs provides a broadly applicable molecular strategy for inducing p ‐PHJ architectures and regulating J D toward high‐performance OPDs.
- 12 September 2026
- Published by Wiley in Advanced Functional Materials
- Vol. 36 (85)
Open AccessOligoethylene Glycol Side‐Chain Engineering of Y6‐Derived Nonfullerene Acceptors for Thermally Induced Spontaneous Pseudo‐Planar Heterojunction Organic Photodetectors
Dark current density ( J D ) fundamentally limits the noise characteristics and detectivity of organic photodetectors (OPDs), arising primarily from reverse‐bias carrier injection and trap‐mediated leakage pathways in donor‐acceptor (D‐A) bulk‐heterojunction (BHJ) active layers. Although pseudo‐planar heterojunction ( p ‐PHJ) architectures effectively suppress these losses, their implementation often requires complex layer engineering or controlled processing conditions. Here, we report two Y6‐derived nonfullerene acceptors (NFAs), YTEG‐4F and YTEG‐4Cl, bearing hydrophilic oligoethylene glycol (OEG) side chains that induce thermally driven spontaneous vertical phase separation within the D‐A BHJ layer. This molecular modification enables p‐PHJ formation, suppressing reverse‐bias carrier injection and leakage pathways, thereby reducing J D . In contrast to the thermally annealed PM6:Y6 device, which exhibits an increased J D of 6.64 × 10 −7 A cm −2 , the PM6:YTEG‐4F and PM6:YTEG‐4Cl devices achieve low J D s of 2.76 × 10 −9 and 3.24 × 10 −9 A cm −2 , corresponding to approximately 260‐fold and 210‐fold reductions after thermal annealing, respectively. Consequently, shot‐noise‐limited detectivities ( D sh *) of 1.17 × 10 13 and 9.74 × 10 12 Jones are achieved at −0.5 V for PM6:YTEG‐4F and PM6:YTEG‐4Cl p ‐PHJ OPDs, respectively. This work demonstrates that OEG side‐chain engineering of NFAs provides a broadly applicable molecular strategy for inducing p ‐PHJ architectures and regulating J D toward high‐performance OPDs.
- 19 December 2024
- Published by Elsevier in Chemical Engineering Journal
- Vol. 504
Symmetric and asymmetric non-fullerene acceptors cooperate synergistically for ternary optoelectronic devices
- 19 December 2024
- Published by Elsevier in Chemical Engineering Journal
- Vol. 504
Symmetric and asymmetric non-fullerene acceptors cooperate synergistically for ternary optoelectronic devices
- Open Access
- 21 March 2024
- Published by IOP Publishing in Journal of Physics: Energy
- Vol. 6 (2) , 025015
Enhancing the indoor performance of organic photovoltaic devices: interface engineering with an aminobenzoic-acid-based self-assembled monolayer
Significant advances in the performance of organic photovoltaic (OPV) devices can facilitate their use in internet of things applications. However, achieving excellent photostability and high efficiency using stable, efficient OPV devices in indoor settings is considerably difficult. To address this issue, a zinc oxide (ZnO) electron transport layer (ETL) was modified with a self-assembled monolayer of 4-aminobenzoic acid (ABA) in the present study, and the impact of this modification was correlated with the indoor performance of an OPV device with the PM6:L8-BO photoactive layer. The ABA-treated ZnO ETL exhibited a significant reduction in the work function (from 4.51 to 4.04 eV), surface roughness (from 0.201 to 0.177 nm), and hydrophilicity of an indium-tin-oxide electrode; this aided in selectively extracting charge carriers from the device and minimizing trap-assisted recombination losses. Additionally, the ABA treatment of the ZnO ETL considerably enhanced the electron mobility and recombination resistance. It reduced the trap density, thereby enabling the ZnO/ABA-based device to achieve improved performance. Consequently, the ZnO/ABA-based device exhibited a noteworthy 14.68% higher maximum power output than that of the device without any ZnO surface modification under 1000 lx halogen (HLG) illumination (P out, max = 354.48 and 309 µA cm−2, respectively). Moreover, under thermal illumination conditions (1000 lx HLG lighting), the ZnO/ABA-based device sustained ∼74% of its initial power conversion efficiency over 120 h, significantly higher than its ABA-free equivalent (∼55%).
- 21 March 2024
- Published by IOP Publishing in Journal of Physics: Energy
- Vol. 6 (2) , 025015
Open AccessEnhancing the indoor performance of organic photovoltaic devices: interface engineering with an aminobenzoic-acid-based self-assembled monolayer
Significant advances in the performance of organic photovoltaic (OPV) devices can facilitate their use in internet of things applications. However, achieving excellent photostability and high efficiency using stable, efficient OPV devices in indoor settings is considerably difficult. To address this issue, a zinc oxide (ZnO) electron transport layer (ETL) was modified with a self-assembled monolayer of 4-aminobenzoic acid (ABA) in the present study, and the impact of this modification was correlated with the indoor performance of an OPV device with the PM6:L8-BO photoactive layer. The ABA-treated ZnO ETL exhibited a significant reduction in the work function (from 4.51 to 4.04 eV), surface roughness (from 0.201 to 0.177 nm), and hydrophilicity of an indium-tin-oxide electrode; this aided in selectively extracting charge carriers from the device and minimizing trap-assisted recombination losses. Additionally, the ABA treatment of the ZnO ETL considerably enhanced the electron mobility and recombination resistance. It reduced the trap density, thereby enabling the ZnO/ABA-based device to achieve improved performance. Consequently, the ZnO/ABA-based device exhibited a noteworthy 14.68% higher maximum power output than that of the device without any ZnO surface modification under 1000 lx halogen (HLG) illumination (P out, max = 354.48 and 309 µA cm−2, respectively). Moreover, under thermal illumination conditions (1000 lx HLG lighting), the ZnO/ABA-based device sustained ∼74% of its initial power conversion efficiency over 120 h, significantly higher than its ABA-free equivalent (∼55%).