Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Muhammad Hashami has a total of 39 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Engineering High-Performance Asphalt Binders and Mixtures Through Micro- and Nanocoke/Polymer Hybrid Modification

    by Yerdos Ongarbayev, Muhammad Hashami, Yerbol Tileuberdi, Yerzhan Imanbayev, Ainur Zhambolova, Yernar Kanzharkan, Aliya Kenzhegaliyeva, Aksaule Kydyrali, Dinmukhamed Abdikhan, Talgar Serik

    Polymer modifiers and carbon-based materials have been widely proposed as potential asphalt additives to improve performance. However, limited studies have systematically compared micro- and nanocoke from different sources in combination with SBS and Elvaloy polymers or linked binder rheology with mixture performance. To address this gap, this study investigated the effects of micro- and nanodispersed petroleum and coal coke combined with SBS and Elvaloy polymers on the rheological behavior of asphalt binders and the performance of asphalt concrete mixtures. Rheological properties were evaluated by dynamic shear rheometer (DSR) testing, and asphalt concrete mixtures were tested for compressive strength and crack resistance. The modified systems were successfully used to obtain commercial polymer-modified bitumen grades: BMP 70/100, BMP 50/70 and BMP 35/50. With 1 wt.% micro coal coke and 0.1 wt.% SBS modification, a softening point of 73.7 °C and a penetration of 22.3 × 0.1 mm was observed. Micro coal coke–SBS system showed the highest compressive strength at 20 °C (3.29 MPa), while the largest crack resistance (4.39 MPa) and the best high-temperature mixture strength (0.90 MPa at 50 °C) were obtained when 0.5 wt.% nanocoke and 0.5 wt.% Elvaloy are used. These findings demonstrate that hybrid coke/polymer modification is an effective approach for enhancing asphalt performance, with micro coal coke–SBS systems providing the highest stiffness and rutting resistance, while nanocoke–Elvaloy systems delivered superior crack resistance and overall performance balance.


  • Open Access

    Smart Hydrophobic Surfaces: Nature-Inspired Designs for Sustainable Nanostructure Technologies

    by Aigerim G. Zhaxybayeva, Muhammad Hashami, Meruyert Nazhipkyzy, Nakhypbek U. Aldiyarov, Saltanat S. Kaliyeva, Nazira B. Kassenova, Aina S. Khamitova, Altynbek A. Zhaparov, Adlet T. Otenov

    Hydrophobic and superhydrophobic surfaces have emerged as key solutions for fluid transport, biofouling prevention, and energy efficiency, with market forecasts projecting a compound annual growth rate (CAGR) of over 15% through 2030 due to their broad range of applications. This review critically examines the principles of natural hydrophobicity, as exemplified by lotus leaves and shark skin, and their translation into engineered surfaces via micro/nanofabrication techniques, such as laser patterning, etching, and self-assembly. Recent advances in hybrid nanomaterials have demonstrated WCAs in the range of 140–160°, along with enhanced mechanical strength and chemical stability, enabling applications in self-cleaning, anti-corrosion, and oil–water separation technologies. Superhydrophobic coatings are particularly important for reducing ice adhesion by more than 80%, while drag reduction in pipelines can reach up to 30%, contributing to energy savings. Despite these advances, challenges remain in achieving long-term stability under harsh environmental conditions, minimizing environmental impact, and developing cost-effective, scalable fabrication techniques. Future directions focus on environmentally friendly, multifunctional nanocomposites with switchable wettability, including pH- and light-responsive coatings capable of reversibly transitioning between superhydrophilic (150°) states, paving the way for sustainable and adaptable surface technologies.


  • Open Access

    Sustainable Energy Storage Systems: The Promise of Biomass-Derived Carbon Materials for High-Performance Supercapacitors

    by Aigerim R. Seitkazinova, Muhammad Hashami, Meruyert Nazhipkyzy, Roza G. Abdulkarimova, Zhanar B. Kudyarova, Aigerim G. Zhaxybayeva, Saltanat S. Kaliyeva, Balken T. Kuderina, Bakhytzhan T. Lesbayev

    The rapid demand for sustainable and efficient energy storage solutions has prompted the pursuit of eco-friendly electrode materials. Biomass-derived carbons from food waste offer a promising pathway to meet this need by combining waste valorization, environmental benefits, and high electrochemical performance. This review highlights that food waste biomass is an effective and inexpensive source of precursors for producing high-performance carbon materials for supercapacitors. Food waste, which includes fruit peels and vegetable residues, cereal husks, and oilseed residues, is a good source of lignocellulosic components, heteroatoms, and structural features that determine the electrochemical characteristics of the derived carbons. These wastes produce hierarchically porous carbons with high surface areas (>1500 m2 g−1) on pyrolysis and activation that provide superior ion transport, wettability and pseudocapacitive behaviour. Their electrochemical performance includes capacitances up to 520 F g−1 and energy densities of 35–70 Wh kg−1 in optimized systems, particularly under extended voltage windows or in hybrid supercapacitor configurations, and high cycling stability is equal to or even better than traditional carbons such as activated carbon and graphene. Additionally, biomass valorization contributes to a high level of greenhouse gas capture, decreases landfill, and correlates with the idea of a circular economy. The commercialization potential of biomass-based supercapacitors is supported by recent developments in AI-based optimization, combined with scalable synthesis methods, which would support ecologically, economically, and technologically sustainable energy storage on a large scale.


  • Open Access

    Bitumen Modification with Microcoke: Mechanochemical Activation, Structure, and High-Temperature Rheological Performance

    by Yerdos Ongarbayev, Muhammad Hashami, Yerbol Tileuberdi, Yerzhan Imanbayev, Ainur Zhambolova, Yernar Kanzharkan, Aliya Kenzhegaliyeva, Aksaule Kydyrali, Dinmukhamed Abdikhan

    The modification of road bitumen using micro-sized carbonaceous materials offers a promising route to enhance pavement performance; however, the influence of microdispersed coke derived from coal and petroleum sources has not been sufficiently clarified. In this study, coal and petroleum coke from Pavlodar Petrochemical Plant LLC (Pavlodar, Kazakhstan) were mechanochemically activated and used as the modifiers for BND 100/130 bitumen, produced by Asphaltbeton 1 LLC (Almaty, Kazakhstan). X-ray diffraction and scanning electron microscopy were used to determine the structure and morphology of the resulting coke powders. Standard tests and the Superpave Multiple Stress Creep and Recovery (MSCR) methodology were used to determine the physico-mechanical and rheological properties of the modified binders. Microdispersed granular coke powders produced after mechanochemical activation had a minimum average particle diameter of 8.28 µm (petroleum coke) and 16.64 µm (coal coke), and were mainly an amorphous carbon phase with traces of graphite. Addition of 1 wt.% microdispersed coke resulted in better performance of binder and an enhancement in grades of BND 100/130 to BND 70/100, in line with ST RK 1373-2013. MSCR testing showed that Jnr3.2 is between 2.0–3.0 kPa−1, which is in the S category of AASHTO M 332-20. This study showed how micro-sized coal and petroleum coke can be effectively used as a high-carbon modifier in bitumen, which reflects the possibility of their practical use in asphalt pavements that are subjected to normal traffic conditions.


  • Open Access

    Technological Progress in Sulfur-Based Construction Materials: The Role of Modified Sulfur Cake in Concrete and Bitumen

    by Muhammad Hashami, Yerdos Ongarbayev, Yerbol Tileuberdi, Yerzhan Imanbayev, Ainur Zhambolova, Yernar Kanzharkan

    Modified sulfur cake is a by-product of sulfuric acid and hydrometallurgical processes, and presents an underutilized resource in sustainable infrastructure with significant potential. This review evaluates the current technological innovations as pertaining to the use of modified sulfur cake in the manufacture of sulfur concrete and sulfur-modified bitumen. The processing strategies (thermal, chemical, and mechano-chemical processing, and effects of organic and inorganic additives to promote mechanical, chemical, and thermal behaviors) are discussed systematically. The effect of the modified sulfur cake on the workability, compressive strength, corrosion resistance, and environmental resistance of construction materials, in particular, is tested, with compression strengths beyond 40 MPa being reported, alongside the improved rutting resistance up to 40%. The most critical limitations associated with phase instability, toxic gas release during processing, compositional variability, and the absence of standardization are identified. Correspondingly, to alleviate them, new developments such as blends with sulfur, nano-reinforcements (e.g., carbon nanotubes (CNT), nano-silica), and the incorporation of formulation optimization by machine-learning are considered. The review particularly focuses on the life cycle performance, reduction in volatile organic compounds (VOC) emissions, and circular economy advantages, highlighting modified sulfur cake as an economical and low-carbon alternative to conventional concrete and bitumen. This review mainly aims to bridge the gap between waste valorization and green construction technologies, offering a roadmap for future research and industrial implementation in line with global climate and sustainability goals.


  • Synthesis of Porous Co3O4 NPs by Solution Combustion: Influence of F/O Ratio on Morphology and Porosity

    by M. Hashami, A. Imash, Z. Mansurov

    In this study, porous Co3O4 nanoparticles (NPs) were synthesized through solution combustion synthesis (SCS) method. Precursor cobalt nitrate hexahydrate a


  • Open Access

    A Comprehensive Overview of Co3O4 Nanoparticles: Solution Combustion Synthesis and Potential Applications

    by Togzhan T. Mashan, Muhammad Hashami, Nurgul S. Bergeneva, Nurgul N. Nurmukhanbetova, Aigul S. Beisebayeva, Meruyert Nazhipkyzy, Gulnar U. Mamatova, Aigerim G. Zhaxybayeva

    Co3O4 nanoparticles synthesized by solution combustion synthesis present a versatile platform for the development of porous nanostructures with tunable morphology and physicochemical properties. Synthesis conditions and parameters such as fuel type; fuel-to-oxidizer ratio and temperature control lead yielding; and Co3O4 NPs with fine particle size, surface area, and porosity result in enhancing their electrochemical and catalytic capabilities. This review evaluates present studies about SCS Co3O4 NPs to study how synthesis parameter modifications affect both surface morphology and material structure characteristics including porosity features, which make their improved performance ideal for lithium-ion batteries and supercapacitors. Moreover, the integration of dopants with carbon-based hybrid composites enhances material conductivity and stability by addressing both capacity fading and low electronic conductivity concerns. This review mainly aims to explore the significant relation between fundamental material design principles together with practical uses and provides predictions about future research advancements that aim to enhance the performance of Co3O4 NPs in next-generation energy and environmental technology applications.


  • Open Access

    Integration of Coke and CNMs with Bitumen: Synthesis, Methods, and Characterization

    by Muhammad Hashami, Yerdos Ongarbayev, Yerbol Tileuberdi, Yerzhan Imanbayev, Ainur Zhambolova, Aliya Kenzhegaliyeva, Zulkhair Mansurov

    Carbon-based nanomaterials have emerged as a promising strategy for bitumen modification to enhance the mechanical and thermal performance of pavements. This review evaluates the present advancements in the inclusion of coke and carbon nanomaterials (CNMs) such as carbon nanotubes (CNTs) and graphene into bituminous systems. The findings and limitations of recent experiments in synthesis procedures along with dispersion methods are deeply explored to determine their impact on the rheological properties of bitumen as well as aging resistance and durability characteristics. Petroleum coke enhances bitumen softening points by 10–15 °C and causes up to 30% improvement in rutting resistance while simultaneously prolonging material fatigue life and aging resistance. Bitumen modification through petroleum coke faces challenges in addition to mixing difficulties due to its high viscosity. Moreover, the incorporation of CNTs and graphene as CNMs shows significant enhancements in rutting resistance with improved tensile strength, lower additive requirements, and enhanced dispersion. Both the superior mechanical properties of carbon nanomaterials and processing advancements in nano-enhanced bitumen have the capability to solve technical issues including material costs and specialized mixing processes. Combining coke with CNMs to enhance performance is a future research direction, which could result in economic and scalability considerations. This review comprehensively explores insights into physicochemical interactions, performance outcomes, and processing techniques, crucial for the development of sustainable, high-performance bitumen composites tailored for next-generation infrastructure applications.


  • Open Access

    Synthesis of Co3O4 NPs by solution combustion synthesis (SCS) and their structure morphology: a mini review

    by Z.A. Mansurov, Muhammad Hashami

    This mini-review aims to present the current status of knowledge about cobalt oxide Co3O4 nanoparticles more precisely obtained by solution combustion synthesis, which is a process characterized by its high reaction rate and low cost. Unique features of cobalt (II)(III) oxide Co3O4 nanoparticles are size between 12 and 60 nm, and high surface area and porosity that enhances their performances in fields such as energy storage, environmental and sensing applications. By analysis of various synthesis parameters such as fuel-to-oxidizer ratios, precursor materials, and thermal conditions, this review elucidates how these factors influence particle characteristics and functionality. Furthermore, while extensive research highlights the efficacy of Co3O4 nanoparticles in energy applications, there is a notable need to further studies focusing on their environmental applications, appealing to young scientists to come up with improved solution seeking innovative research areas of nanotechnology and material science. The review offers more avenues for using Co3O4 nanoparticles in solving some of the pressing global environmental issues.


  • Open Access

    Ozonation of Bitumen: Characteristics, Characterization, and Applications

    by Muhammad Hashami, Yerdos Ongarbayev, Dinmukhamed Abdikhan, Erzhan Akkazin, Nuripa Nessipbayeva

    Bitumen is a significant component used in road construction. Traditionally, it is subjected to air-blowing processes at high temperatures (220–260 °C) to enhance its viscosity, rigidity, and oxidation characteristics. However, such approaches are often energy-consuming and result in extensive environmental issues, so more efficient and environmentally friendly techniques are needed. This review evaluates the emerging novel pathways for treating bitumen, with a particular focus on the role of ozone in the air-blowing process. By examining present studies, this review emphasizes the incorporation of ozone as an oxidizing agent to address the current challenges of long process times and high temperatures in the activation process and comprehensively demonstrates the enhancement of bitumen’s mechanical properties through ozone treatment. It also highlights the minimization of toxic emissions this achieves, especially highlighting the crucial role of ozone in improving the characteristics of bitumen in relation to the global trend toward making civil construction projects more environmentally friendly. The main aim of this review is to contribute to the development of new ideas in the field of bitumen modification and to encourage further advances in road construction from the standpoint of improving efficiency and minimizing environmental impacts.