Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Mohamed Fathy Atia has a total of 35 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Thermohydraulic Performance Enhancement of a Solar Air Heater Using Longitudinal Alternating Baffles: Experimental and 3D-CFD Study

    by Fatma M. Shaaban, Sayed Youssef, Mahmoud A. Abdelhamid, Saddam Hussain, Moustafa H. Abozid, Shaimaa A. Hassan, Noura Roushdy, Mohamed F. Atia

    This study presents a comparative experimental and numerical investigation of two solar air heater (SAH) configurations: a flat-panel absorber (F-SAH) and a longitudinal-baffle absorber (LB-SAH). Experiments were conducted under real outdoor conditions at mass flow rates of 0.00410, 0.00513, and 0.00616 kg s−1, and a three-dimensional CFD model was developed in ANSYS Fluent using the SST k–ω turbulence closure. The numerical results showed excellent agreement with experimental data, with a mean deviation not exceeding 4.5%. The LB-SAH consistently outperformed the F-SAH across all operating conditions. For experimental results, the maximum outlet air temperature reached 97 °C for the LB-SAH compared to 79 °C for the F-SAH at a mass flow rate of 0.00410 kg s−1. The thermal efficiency of the LB-SAH ranged from 47.76% to 64.51% as the mass flow rate increased from 0.00410 to 0.00616, compared to 30.77–47.76% for the F-SAH. The LB-SAH achieved Nusselt numbers up to 110.18% higher than those for the F-SAH, with heat transfer coefficients of up to 16.61 W m−2 K−1. The thermohydraulic performance parameter (THPP) reached 1.49 for the LB-SAH configuration at m = 0.00616 kg s−1, confirming significant net energy gains compared to the results for the F-SAH configuration. These findings establish the LB-SAH as the superior configuration in terms of thermal performance, while highlighting the F-SAH as the preferred choice when minimizing hydraulic resistance is a priority. While the LB-SAH significantly enhances heat transfer performance, this improvement is accompanied by an increased pressure drop and higher fan power requirements.

  • Top Cited Papers
    Open Access

    Design and evaluation of a solar powered smart irrigation system for sustainable urban agriculture

    by Mahmoud A. Abdelhamid, Tarek Kh. Abdelkader, Hassan A. A. Sayed, Zhao Zhang, Xiaohui Zhao, Mohamed F. Atia

    Urban areas face significant challenges, including a lack of green spaces, scarce water resources, environmental pollution, and elevated heat emissions, particularly in developing countries experiencing rapid population growth. Therefore, the study aims to advance sustainable urban agriculture by designing and evaluating a solar-powered smart rooftop irrigation system for peppermint cultivation. The system incorporates two drip irrigation setups—conventional and smart irrigation—powered by photovoltaic (PV) panels. The smart system integrates real-time monitoring of critical variables, including (1) soil moisture, (2) relative humidity, (3) PV panel temperature, and (4) PV panel current and voltage. Key performance metrics such as water and energy consumption, water use efficiency, energy productivity, and carbon dioxide emissions were evaluated for both systems. In addition, the economic analysis of the smart system was determined. Results revealed that the smart system reduced water and energy consumption by 28.1% compared to conventional irrigation. Additionally, the smart system achieved a notable reduction in carbon footprint, with CO2 emissions of 0.181 kg CO₂/m2/year compared to 0.252 kg CO₂/m2/year for the conventional system. The system’s economic analysis demonstrated a payback period of 5.6 years, highlighting its financial viability. This study underscores the transformative potential of solar-powered smart irrigation systems in enhancing food security, conserving water, reducing energy consumption, and mitigating carbon emissions in urban agriculture.


  • Open Access

    Thermal Performance Analysis of an Indirect Solar Cooker Using a Graphene Oxide Nanofluid

    by Fatma M. Shaaban, M. F. Abdel-Salam, Khaled Y. Farroh, Han Wang, Mohamed F. Atia

    Solar energy has become an energy source for a wide range of uses, including in solar cookers, due to its availability, cleanliness, environmental friendliness, and sustainability. In this study, an indirect solar cooker was investigated by measuring its thermal performance using a Graphene Oxide (GO) nanofluid. Water, GO (250 ppm)-water, and GO (500 ppm)-water were used as heat transfer fluids. The experimental set-up consisted of the cooking part and a solar collector, which are the two essential elements in indirect solar cookers. The cooking part was a wooden box solar cooker, and the parabolic trough solar collector was a polished stainless steel structure. The solar cooker was assessed using the stagnation test and load test as well as energy and exergy measurements. According to the test results, the averaged F1 was 0.1 for the base fluid water, 0.11 for GO (250 ppm)-water, and 0.13 for GO (500 ppm)-water. In addition, using a GO nanofluid instead of water in the solar cooker, the system’s thermal performance, energy, and exergy efficiency were improved. The use of the GO (250 ppm)-water and GO (500 ppm)-water nanofluids instead of water in the system improved the overall energy efficiency of the system by 3.3 and 4.2%. Moreover, using GO (500 ppm)-water allowed for achieving superior performance.


  • Open Access

    Using desalinated water from solar stills to irrigate green beans (Phaseolus vulgaris L.) in different water regimes with an application of 15N stable isotope

    by M.A. Salama, Y.G.M. Galal, M.A. Hussien, M.F. Atia, I.F.M. Eldehn

    A pot experiment in the open field was conducted to evaluate the performance of a green bean crop under different irrigation water regimes and two types of solar still (Active and Passive). Irrigation water was applied at regimes of 170, 142, and 114 mm in season, representing T1 (100% WHC), T2 (80% WHC), and T3 (70% WHC) from water holding capacity (WHC), respectively. During the measurement months, the average monthly output of active solar still productivity is 1790 ml m-2 with an average overall thermal efficiency (ηactive) of 5.9%, while in the passive solar still productivity is 1308 ml m-2 with an average overall thermal efficiency (ηpassive) of 17.6%. The desalinated water applied at T1 enhanced growth characteristics, yield, and improved water productivity (WP) and water use efficiency (WUE) compared to T2 and T3 deficit water regimes. Similarly, increasing irrigation water availability to plants improved NPK nutrient uptake by various plant parts. The 15N/14N ratio analysis revealed that under all irrigation water regimes, the absolute values of the N portion derived from fertilizer were higher in pods, followed by shoots, and then roots. In contrast with the nitrogen derived from fertilizer (Ndff), the absolute values of Ndff in pods, shoots, and roots seem significantly higher under T1 than those indicated at either the T2 or T3 regimes. In this respect, the nitrogen use efficiency (NUE) reached nearly 64% and 51% for pods and shoots under the T1 regime, while those for roots were still negligible. These percentages of NUE in pods and shoots tended to decrease gradually with increasing water deficits (T2 and T3).


  • Open Access

    Assessment of tomato ripeness using chlorophyll fluorescence

    by Mahmoud A. Abdelhamid, S. A. Rawdhan, Shereen S. Shalaby, Mohamed F. Atia

    The ripeness of tomatoes has a direct impact on their quality. This study aimed to develop mathematical models to determine and monitor tomato ripeness based on chlorophyll fluorescence parameters. Three varieties of tomatoes (Alkazar, Lezginka, and Rosanchik) with five ripening stages (green, breaker, pink, light red, and red) were examined using chlorophyll fluorescence analysis. Chlorophyll fluorescence variables (Variable - Fv, maximum - Fm, initial - F0, and Fv/Fm ratio) were assessed at five stages of maturation. Five mathematical models were proposed for each tomato variety examined to determine the relationship between chlorophyll fluorescence parameters and ripening stages. The experimental results revealed that tomato maturity could be determined using chlorophyll fluorescence. It was found that as the tomato fruits ripened, the chlorophyll fluorescence parameters, such as Fv, Fv/Fm, Fm, and F0, gradually decreased. The proposed models allowed estimation of the ripening stage of all three tomato varieties. The highest R2 (0.99) was obtained using chlorophyll fluorescence parameters together.


  • Evaluation of Solar Water Distiller Coupled with Solar Evacuated Tubes

    by Israa Fathy Eldehn, Mubarak Mohamed Mustafa, Mohamed Fathy Atia, Mohamed Abd Elaal Salama, Yehia Galal Mohamed Galal, Mohamed Abd Elmoniem Hussein

    The scarcity of fresh water is a main problem in remote regions. Economical and related water distillation solar still coupled with a solar collector was designed and studied experimentally. This study aims to investigate and evaluate the performance of active single slope solar still (ASSSS) coupled with solar evacuated tubes collector (ETC) as water heater. Results show that the average distillate productivity of ASSSS combined with U pipe evacuated tubes solar collector (ETC) was 1.085 l/m2 in December/2020, while at August/2021 recorded 3.12 l/m2. These quantities of distiller water were higher than those produced by solar passive distiller with single slope (PSSSS). For the average values of water temperature increased by using ASSSS coupled with ETC in August/2021 was 79.1°C while it was 71°C in August/2021 for PSSSS. These results indicated that the ASSSS is more effective than the PSSSS.

  • Open Access

    Maximizing the utilization of solar energy in drying of potato

    by Mustafa A. Farhan, Mubarak M. Mustafa, Yhia A. Heikal, Mohamed F. Atia

    This study was proceeded to adjudge a maximizing the utilization of solar Energy in the drying of potato, Experimental work was proceeded under different levels of temperature and thickness of Potato slices “2-3mm” at constant air velocity of 0.78 m/min. The experimental measurements included moisture content Potato slices, air temperature, air relative humidity, solar drying efficiency and changes of the drying rate Potato Measuring the utilization rate of solar energy, with mirrors or without mirrors. The moisture content of potato decreased from 80.9 to 5.55 kg/kg for potato slices treated using mirrors, this decrease in moisture content was greater than when the slides were not treated and without mirrors.

  • DEVELOPMENT AND THERMAL PERFORMANCE ANALYSIS EVALUATION OF A TRUNCATED PYRAMID SOLAR COOKER

    by Fatma M. Shaaban, M. M. Mostafa, M. F. Abdel-Salam, M. F. Atia

    Study aimed to develop and evaluate the thermal performance of truncated pyramid solar cooker viz non-modified and modified. Tests have been carried out in Department of Agricultural Engineering, Faculty of Agriculture, Ain Shams University, Shubra El-Kheima, Egypt (Latitude 30o11’ N, Longitude 31o24’ E). The solar cookers were not loaded, and loaded with 0.5, 1.0 and 2.0 liter of water. The modified truncated pyramid was filled with different quantities of rice. The thermal performance was evaluated by using first figure of Merit, second figure of Merit and energy efficiency. textural properties of rice and biscuits and cost analysis were measured. The absorber plate temperature of the modified was 51. 8 % higher than the absorber plate temperature of the non-modified cooker. The calculated values of first figure of Merit was 0.102 and 0.08 oC.m2/W with modified and non-modified truncated pyramid cooker types, respectively. The value of second figure of Merit was 0.239 and 0.523 for modified and non-modified truncated pyramid cooker, respectively.