Ashley Dan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Ashley Dan has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Rohit Ramachandran
Chemical and Biochemical Engineering, Rutgers University, Piscataway, USA
2 shared publications - Andrés David Román-Ospino
Engineering Research Center for Structured Organic Particulate Systems (C-SOPS), Department of Chemistry, University of Puerto Rico, Mayaguez Campus, Mayaguez, PR 00681, USA
1 shared publication - Erik Holmen Olofsson
Department of Mechanical Engineering, Technical University of Denmark, Kgs. Lyngby, Denmark
1 shared publication - Jesper Henri Hattel
Department of Civil and Mechanical Engineering, Technical University of Denmark, Kongens Lyngby, Denmark
1 shared publication - Lalith Kotamarthy
Department of Chemical & Biochemical Engineering, Rutgers University, 98 Brett Road, Piscataway, NJ 08854, USA
1 shared publication - Michael Roland Larsen
Department of Civil and Mechanical Engineering, Technical University of Denmark, 2800 Kongens Lyngby, Denmark
1 shared publication
Latest Publications
- Open Access
- 25 March 2024
- Published by MDPI AG in Pharmaceutics
- Vol. 16 (4) , 456
Investigating the Effects of Mixing Dynamics on Twin-Screw Granule Quality Attributes via the Development of a Physics-Based Process Map
Twin-screw granulation (TSG) is an emerging continuous wet granulation technique that has not been widely applied in the industry due to a poor mechanistic understanding of the process. This study focuses on improving this mechanistic understanding by analyzing the effects of the mixing dynamics on the granule quality attributes (PSD, content uniformity, and microstructure). Mixing is an important dynamic process that simultaneously occurs along with the granulation rate mechanisms during the wet granulation process. An improved mechanistic understanding was achieved by identifying and quantifying the physically relevant intermediate parameters that affect the mixing dynamics in TSG, and then their effects on the granule attributes were analyzed by investigating their effects on the granulation rate mechanisms. The fill level, granule liquid saturation, extent of nucleation, and powder wettability were found to be the key physically relevant intermediate parameters that affect the mixing inside the twin-screw granulator. An improved geometrical model for the fill level was developed and validated against existing experimental data. Finally, a process map was developed to depict the effects of mixing on the temporal and spatial evolution of the materials inside the twin-screw granulator. This process map illustrates the mechanism of nucleation and the growth of the granules based on the fundamental material properties of the primary powders (solubility and wettability), liquid binders (viscosity), and mixing dynamics present in the system. Furthermore, it was shown that the process map can be used to predict the granule product quality based on the granule growth mechanism.
- 25 March 2024
- Published by MDPI AG in Pharmaceutics
- Vol. 16 (4) , 456
Open AccessInvestigating the Effects of Mixing Dynamics on Twin-Screw Granule Quality Attributes via the Development of a Physics-Based Process Map
Twin-screw granulation (TSG) is an emerging continuous wet granulation technique that has not been widely applied in the industry due to a poor mechanistic understanding of the process. This study focuses on improving this mechanistic understanding by analyzing the effects of the mixing dynamics on the granule quality attributes (PSD, content uniformity, and microstructure). Mixing is an important dynamic process that simultaneously occurs along with the granulation rate mechanisms during the wet granulation process. An improved mechanistic understanding was achieved by identifying and quantifying the physically relevant intermediate parameters that affect the mixing dynamics in TSG, and then their effects on the granule attributes were analyzed by investigating their effects on the granulation rate mechanisms. The fill level, granule liquid saturation, extent of nucleation, and powder wettability were found to be the key physically relevant intermediate parameters that affect the mixing inside the twin-screw granulator. An improved geometrical model for the fill level was developed and validated against existing experimental data. Finally, a process map was developed to depict the effects of mixing on the temporal and spatial evolution of the materials inside the twin-screw granulator. This process map illustrates the mechanism of nucleation and the growth of the granules based on the fundamental material properties of the primary powders (solubility and wettability), liquid binders (viscosity), and mixing dynamics present in the system. Furthermore, it was shown that the process map can be used to predict the granule product quality based on the granule growth mechanism.
- Open Access
- 19 March 2024
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 132 (3-4) , 1111-1125
Numerical modeling of fill-level and residence time in starve-fed single-screw extrusion: a dimensionality reduction study from a 3D CFD model to a 2D convection-diffusion model
This research delves into the numerical predictions of fill-level and residence time distribution (RTD) in starve-fed single-screw extrusion systems. Starve-feeding, predominantly used in ceramic extrusion, introduces challenges which this study seeks to address. Based on a physical industrial system, a comprehensive 3D computational fluid dynamics (CFD) model was developed using a porous media representation of the complex multi-hole plate die. Validations performed using real sensor data, accounting for partial wear on auger screw flights, show an ~11% discrepancy without accounting for screw wear and ~6% when considering it. A 2D convection-diffusion model was introduced as a dimensionality reduced order model (ROM) with the intention of bridging the gap between comprehensive CFD simulations and real-time applications. Central to this model’s prediction ability was both the velocity field transfer from the CFD model and calibration of the ROM diffusion coefficient such that a precise agreement of residence time distribution (RTD) curves could be obtained. Some discrepancies between the CFD and the ROM were observed, attributed to the loss of physical information of the system when transitioning from a higher fidelity CFD model to a semi-mechanistic ROM and the inherent complexities of the starved flow in the compression zone of the extruder. This research offers a comprehensive methodology and insights into reduced order modeling of starve-fed extrusion systems, presenting opportunities for real-time optimization and enhanced process understanding.
- 19 March 2024
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 132 (3-4) , 1111-1125
Open AccessNumerical modeling of fill-level and residence time in starve-fed single-screw extrusion: a dimensionality reduction study from a 3D CFD model to a 2D convection-diffusion model
This research delves into the numerical predictions of fill-level and residence time distribution (RTD) in starve-fed single-screw extrusion systems. Starve-feeding, predominantly used in ceramic extrusion, introduces challenges which this study seeks to address. Based on a physical industrial system, a comprehensive 3D computational fluid dynamics (CFD) model was developed using a porous media representation of the complex multi-hole plate die. Validations performed using real sensor data, accounting for partial wear on auger screw flights, show an ~11% discrepancy without accounting for screw wear and ~6% when considering it. A 2D convection-diffusion model was introduced as a dimensionality reduced order model (ROM) with the intention of bridging the gap between comprehensive CFD simulations and real-time applications. Central to this model’s prediction ability was both the velocity field transfer from the CFD model and calibration of the ROM diffusion coefficient such that a precise agreement of residence time distribution (RTD) curves could be obtained. Some discrepancies between the CFD and the ROM were observed, attributed to the loss of physical information of the system when transitioning from a higher fidelity CFD model to a semi-mechanistic ROM and the inherent complexities of the starved flow in the compression zone of the extruder. This research offers a comprehensive methodology and insights into reduced order modeling of starve-fed extrusion systems, presenting opportunities for real-time optimization and enhanced process understanding.