Serhii Iovchev
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Serhii Iovchev has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Mykola Malaksiano
Department of Technical Cybernetics and Information Technology, Odesa National Maritime University, Mechnikov 34, 65029 Odessa, Ukraine
2 shared publications - Oleksandr Shumylo
Odesa National Maritime University
2 shared publications - Oleksiy Melnyk
Odesa National Maritime University, Odesa, Ukraine
2 shared publications - Volodymyr Yarovenko
Odesa National Maritime University
2 shared publications - A.O. Briukhanov1 shared publication
Artur Zaporozhets
1 shared publication
Latest Publications
- 14 July 2026
- Published by Springer Nature
- p. 267-283
Influence of Wind Load on Maneuverability and Controllability of Electric Vessels with Active Motion Control Systems
- 14 July 2026
- Published by Springer Nature
- p. 267-283
Influence of Wind Load on Maneuverability and Controllability of Electric Vessels with Active Motion Control Systems
- 1 July 2025
- Published by Springer Nature in Materials Science
- Vol. 61 (1) , 16-22
Crystallographic texture of aluminum alloy samples produced by additive friction-stirred deposition
- 1 July 2025
- Published by Springer Nature in Materials Science
- Vol. 61 (1) , 16-22
Crystallographic texture of aluminum alloy samples produced by additive friction-stirred deposition
- 25 February 2025
- Published by Springer Nature
- p. 235-255
Methods for Assessing Electric Ships’ Maneuvering and Safety Indicators Based on the Theory of the Dynamic Similarity
- 25 February 2025
- Published by Springer Nature
- p. 235-255
Methods for Assessing Electric Ships’ Maneuvering and Safety Indicators Based on the Theory of the Dynamic Similarity
- Open Access
- 29 March 2024
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Metaloznavstvo ta obrobka metalìv
- Vol. 30 (1) , 18-27
Recrystallization texture and anisotropy of elastic properties of DC04 steel sheets
We studied steel sheets DC04 (0.06% C, up to 0.35% Mn, up to 0.40% Si, ~ 0.025% S and P) with a thickness of 0.95 mm as delivered.Sheets of A4 size were annealed in a laboratory oven (600°C in an argon atmosphere, hold for 1 hour).The structure of DC04 steel sheets after recrystallization annealing was studied. The microstructure of the steel sheets under study is presented from the side of the rolling plane and in the section of the sheet perpendicular to the direction. In the plane of the sheets, the grains are elongated; in the cross section, the grains are approximately equiaxed.Pole figures (PF) were constructed based on the results of electron backscatter diffraction (EBSD) on a LEO 1455 VP electron microscope at an accelerating voltage of 20 kV from the plane of the sheets and from the section of the sheet perpendicular to the rolling direction. To improve statistics, PF were constructed by averaging reflex stereographic projections from 20 different representative volumes of material relative to the rolling direction and transverse direction.The texture and anisotropy of Young's modulus in the plane and cross section of steel sheets DC04 after recrystallization annealing was studied using EBSD method. A connection has been obtained between ideal orientations that describe the texture in two mutually perpendicular planes and the corresponding integral characteristics of texture (ICT).Rectangular samples with a length of 100 and a width of 10 mm at different angles to the rolling direction every 150 to measure Young's modulus. Samples were processed in a bag to ensure uniform dimensions. Young's modulus was determined by the dynamic method from the frequency of natural transverse vibrations. Three batches of samples were used to construct Young's modulus anisotropy curves.The anisotropy of the Young's modulus in the plane of steel sheets, calculated from the ICT based on the results of EBSD data, is in good agreement with the results of direct measurements. The value of Young's modulus in the direction normal to the plane of the sheet and in the section plane in the direction normal to the plane of the sheet, calculated from the ICT and the values of the compliance constants of iron, coincide. Досліджували листи сталі DC04 (0.06% С, до 0.35% Mn, до 0.40% Si, ~ 0.025% S і P) товщиною 0.95 мм в умовах постачання. Листи розміром А4 піддавали відпалу в лабораторній печі (600 °С в атмосфері аргону, витримка 1 год.). Вивчали структуру листів сталі DC04 після рекристалізаційного відпалу. Представлена мікроструктура досліджуваних листів сталі з боку площини прокатки та перерізу листа, перпендикулярного напрямку прокатки. У площині листів зерна витягнуті, поперечному перерізі – зерна приблизно рівновісні.Полюсні фігури (ПФ) будували за результатами дифракції зворотного розсіювання електронів (ДЗРЕ) на електронному мікроскопі LEO 1455 VP при прискорювальній напрузі 20 кV від площини листів і від перерізу листа, перпендикулярного до напрямку прокатки. Для покращення статистики ПФ будували шляхом усереднення рефлексних стереографічних проекцій від 20 різних представницьких об’ємів матеріалу відносно напряму прокатки та поперечного напряму.Методом ДЗРЕ вивчали текстуру та анізотропію модуля Юнга у площині та поперечному перерізі листів сталі DC04 після рекристалізаційного відпалу. Отримано зв'язок між ідеальними орієнтуваннями, що описують текстуру у двох взаємно перпендикулярних площинах, та відповідними інтегральними характеристиками текстури (ІХТ).З листів вирізали прямокутні зразки довжиною 100 мм та шириною 10 мм під різними кутами до напрямку прокатки через кожні 15° для вимірювання модуля Юнга. Зразки оброблялися в пакеті для забезпечення однакових розмірів. Модуль Юнга визначали динамічним способом за частотою власних поперечних коливань. При побудові кривих анізотропії модуля Юнга використовували три партії зразків.Анізотропія модуля Юнга у площині листів сталі, розрахована з ІХТ за результатами даних ДЗРЕ, перебуває у згоді з результатами прямих вимірів. Значення модуля Юнга в нормальному до площини листа напрямку і площині перерізу в напрямку нормалі до площини листа, розраховані з ІХТ і значенням констант податливості заліза, збігаються.
- 29 March 2024
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Metaloznavstvo ta obrobka metalìv
- Vol. 30 (1) , 18-27
Open AccessRecrystallization texture and anisotropy of elastic properties of DC04 steel sheets
We studied steel sheets DC04 (0.06% C, up to 0.35% Mn, up to 0.40% Si, ~ 0.025% S and P) with a thickness of 0.95 mm as delivered.Sheets of A4 size were annealed in a laboratory oven (600°C in an argon atmosphere, hold for 1 hour).The structure of DC04 steel sheets after recrystallization annealing was studied. The microstructure of the steel sheets under study is presented from the side of the rolling plane and in the section of the sheet perpendicular to the direction. In the plane of the sheets, the grains are elongated; in the cross section, the grains are approximately equiaxed.Pole figures (PF) were constructed based on the results of electron backscatter diffraction (EBSD) on a LEO 1455 VP electron microscope at an accelerating voltage of 20 kV from the plane of the sheets and from the section of the sheet perpendicular to the rolling direction. To improve statistics, PF were constructed by averaging reflex stereographic projections from 20 different representative volumes of material relative to the rolling direction and transverse direction.The texture and anisotropy of Young's modulus in the plane and cross section of steel sheets DC04 after recrystallization annealing was studied using EBSD method. A connection has been obtained between ideal orientations that describe the texture in two mutually perpendicular planes and the corresponding integral characteristics of texture (ICT).Rectangular samples with a length of 100 and a width of 10 mm at different angles to the rolling direction every 150 to measure Young's modulus. Samples were processed in a bag to ensure uniform dimensions. Young's modulus was determined by the dynamic method from the frequency of natural transverse vibrations. Three batches of samples were used to construct Young's modulus anisotropy curves.The anisotropy of the Young's modulus in the plane of steel sheets, calculated from the ICT based on the results of EBSD data, is in good agreement with the results of direct measurements. The value of Young's modulus in the direction normal to the plane of the sheet and in the section plane in the direction normal to the plane of the sheet, calculated from the ICT and the values of the compliance constants of iron, coincide. Досліджували листи сталі DC04 (0.06% С, до 0.35% Mn, до 0.40% Si, ~ 0.025% S і P) товщиною 0.95 мм в умовах постачання. Листи розміром А4 піддавали відпалу в лабораторній печі (600 °С в атмосфері аргону, витримка 1 год.). Вивчали структуру листів сталі DC04 після рекристалізаційного відпалу. Представлена мікроструктура досліджуваних листів сталі з боку площини прокатки та перерізу листа, перпендикулярного напрямку прокатки. У площині листів зерна витягнуті, поперечному перерізі – зерна приблизно рівновісні.Полюсні фігури (ПФ) будували за результатами дифракції зворотного розсіювання електронів (ДЗРЕ) на електронному мікроскопі LEO 1455 VP при прискорювальній напрузі 20 кV від площини листів і від перерізу листа, перпендикулярного до напрямку прокатки. Для покращення статистики ПФ будували шляхом усереднення рефлексних стереографічних проекцій від 20 різних представницьких об’ємів матеріалу відносно напряму прокатки та поперечного напряму.Методом ДЗРЕ вивчали текстуру та анізотропію модуля Юнга у площині та поперечному перерізі листів сталі DC04 після рекристалізаційного відпалу. Отримано зв'язок між ідеальними орієнтуваннями, що описують текстуру у двох взаємно перпендикулярних площинах, та відповідними інтегральними характеристиками текстури (ІХТ).З листів вирізали прямокутні зразки довжиною 100 мм та шириною 10 мм під різними кутами до напрямку прокатки через кожні 15° для вимірювання модуля Юнга. Зразки оброблялися в пакеті для забезпечення однакових розмірів. Модуль Юнга визначали динамічним способом за частотою власних поперечних коливань. При побудові кривих анізотропії модуля Юнга використовували три партії зразків.Анізотропія модуля Юнга у площині листів сталі, розрахована з ІХТ за результатами даних ДЗРЕ, перебуває у згоді з результатами прямих вимірів. Значення модуля Юнга в нормальному до площини листа напрямку і площині перерізу в напрямку нормалі до площини листа, розраховані з ІХТ і значенням констант податливості заліза, збігаються.