Pau Estarlich
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Pau Estarlich has a total of 57 co-authors. Here are the top co-authors by number of shared publications:
- Gerard Masmitjà
Department of Electronic Engineering, Universitat Politècnica de Catalunya (UPC), 08034 Barcelona, Spain
5 shared publications - Cristobal Voz
Universitat Politecnica de Catalunya
3 shared publications - Joaquim Puigdollers
Photovoltaic Lab-Micro and Nano Technologies Group (MNT), Electronic Engineering Department, Universitat Politècnica de Catalunya (UPC), Barcelona 08026, Spain
3 shared publications - Alex Jimenez-Arguijo
Universitat Politecnica de Catalunya
2 shared publications - Arnau Torrens
Universitat Politècnica de Catalunya (UPC) Photovoltaic Lab ‐ Micro and Nano Technologies Group (MNT) Electronic Engineering Department, EEBE Barcelona Spain
2 shared publications - Carlos Molpeceres
Centro Laser, Universidad Politécnica de Madrid, C/Alan Turing 1, 28038 Madrid, Spain
2 shared publications
Latest Publications
- Open Access
- 13 July 2026
- Published by Elsevier in SSRN Electronic Journal
Influence of a capping layer on ultrashort pulse laser removal of thin oxide films
Laser-based selective thin film removal is a key process in microelectronics manufacturing, where functional layers must be removed with high precision while preserving the integrity of the underlying substrate. In many technologically relevant systems, thin films are covered by additional capping layers, whose influence on the removal mechanisms remains poorly understood. In this work, we investigate the selective laser removal of VOx and AZO-capped VOx thin films deposited on silicon using time-resolved pump–probe microscopy in combination with final state crater analysis. For both systems, thin film removal is governed by indirectly induced ablation, whereby laser energy is predominantly absorbed in the silicon substrate, leading to stress-driven film lift-off. At higher fluences, the onset of phase explosion induces substrate damage and prevents selective thin film removal. The presence of the AZO capping layer reduces the processing fluence window for selective thin film removal by approximately 30%, enhances the confinement of the molten substrate and suppresses silicon substrate removal. In addition, residual fragments of the capping layer remain on the surface after processing. These findings demonstrate that capping layers significantly alter both the process window and the underlying removal dynamics and must therefore be carefully considered in the design and optimization of laser-based thin film removal processes.
- 13 July 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessInfluence of a capping layer on ultrashort pulse laser removal of thin oxide films
Laser-based selective thin film removal is a key process in microelectronics manufacturing, where functional layers must be removed with high precision while preserving the integrity of the underlying substrate. In many technologically relevant systems, thin films are covered by additional capping layers, whose influence on the removal mechanisms remains poorly understood. In this work, we investigate the selective laser removal of VOx and AZO-capped VOx thin films deposited on silicon using time-resolved pump–probe microscopy in combination with final state crater analysis. For both systems, thin film removal is governed by indirectly induced ablation, whereby laser energy is predominantly absorbed in the silicon substrate, leading to stress-driven film lift-off. At higher fluences, the onset of phase explosion induces substrate damage and prevents selective thin film removal. The presence of the AZO capping layer reduces the processing fluence window for selective thin film removal by approximately 30%, enhances the confinement of the molten substrate and suppresses silicon substrate removal. In addition, residual fragments of the capping layer remain on the surface after processing. These findings demonstrate that capping layers significantly alter both the process window and the underlying removal dynamics and must therefore be carefully considered in the design and optimization of laser-based thin film removal processes.
- Open Access
- 25 June 2026
- Published by Elsevier in SSRN Electronic Journal
Selective femtosecond IR laser patterning windows for VOx, MoOx, and WOx thin films on crystalline silicon
This study investigates selective femtosecond infrared laser ablation of ultrathin VOx, MoOx, and WOx films deposited on crystalline silicon, targeting residue-free patterning without modifying the substrate. A 1030 nm, 320 fs laser was used to quantify the fluence thresholds for complete film removal and substrate damage, thereby defining a selective processing window for each oxide. Thresholds and beam radius were extracted from single-pulse crater diameters using the established Gaussian-beam crater-diameter method. Confocal 3D microscopy was employed to characterize crater morphology and groove continuity, and to relate process outcomes to fluence and pulse overlap constraints during high-speed scribing. Finally, diode isolation experiments show a reduction of reverse leakage current after laser scribing, supporting the suitability of femtosecond laser patterning for defining active areas in TMO/Si device stacks.
- 25 June 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessSelective femtosecond IR laser patterning windows for VOx, MoOx, and WOx thin films on crystalline silicon
This study investigates selective femtosecond infrared laser ablation of ultrathin VOx, MoOx, and WOx films deposited on crystalline silicon, targeting residue-free patterning without modifying the substrate. A 1030 nm, 320 fs laser was used to quantify the fluence thresholds for complete film removal and substrate damage, thereby defining a selective processing window for each oxide. Thresholds and beam radius were extracted from single-pulse crater diameters using the established Gaussian-beam crater-diameter method. Confocal 3D microscopy was employed to characterize crater morphology and groove continuity, and to relate process outcomes to fluence and pulse overlap constraints during high-speed scribing. Finally, diode isolation experiments show a reduction of reverse leakage current after laser scribing, supporting the suitability of femtosecond laser patterning for defining active areas in TMO/Si device stacks.
- Open Access
- 20 October 2025
- Published by Royal Society of Chemistry (RSC) in EES Catalysis
- Vol. 4 (1) , 163-174
Minimalist and nanoparticle-free selenium-based photocathodes for record performance solar-driven hydrogen evolution
This work reports the highest photoelectrochemical (PEC) performance for selenium (Se)-based photocathodes, achieved through a simple, sustainable, and nanoparticle-free design. A half-cell solar-to-hydrogen (HC-STH) efficiency of 2.78 ± 0.01% and a photocurrent density of 11.35 ± 0.01 mA/cm2 at 0 VRHE were obtained with bare Mo/Se devices tested in H2SO4, surpassing the previous Se-based (FTO/Se/TiO2/Pt) HC-STH benchmark by over a factor of seven. To improve sustainability and device safety, the deposition of a thin TiO2 passivation layer enabled comparable performance (2.76 ± 0.01%), even in neutral phosphate buffer, allowing to obtain the highest photoelectrocatalytic onset potential reported so far (0.74 VRHE). Unlike most PEC devices that rely on complex multilayer stacks and costly noble metals, which limit scalability and environmental compatibility, this work demonstrates that high performance can be achieved with a fully earth-abundant and low-toxicity materials set. A systematic screening of back contacts, Se phases, absorber thickness, protective overlayers, and electrolyte formulations revealed the crucial role of Mo in enhancing Se orientation, charge extraction, and photovoltage generation. These results establish multiple benchmarks for Se-based PEC water splitting and highlight the potential of streamlined and scalable architectures for efficient and sustainable green hydrogen production.
- 20 October 2025
- Published by Royal Society of Chemistry (RSC) in EES Catalysis
- Vol. 4 (1) , 163-174
Open AccessMinimalist and nanoparticle-free selenium-based photocathodes for record performance solar-driven hydrogen evolution
This work reports the highest photoelectrochemical (PEC) performance for selenium (Se)-based photocathodes, achieved through a simple, sustainable, and nanoparticle-free design. A half-cell solar-to-hydrogen (HC-STH) efficiency of 2.78 ± 0.01% and a photocurrent density of 11.35 ± 0.01 mA/cm2 at 0 VRHE were obtained with bare Mo/Se devices tested in H2SO4, surpassing the previous Se-based (FTO/Se/TiO2/Pt) HC-STH benchmark by over a factor of seven. To improve sustainability and device safety, the deposition of a thin TiO2 passivation layer enabled comparable performance (2.76 ± 0.01%), even in neutral phosphate buffer, allowing to obtain the highest photoelectrocatalytic onset potential reported so far (0.74 VRHE). Unlike most PEC devices that rely on complex multilayer stacks and costly noble metals, which limit scalability and environmental compatibility, this work demonstrates that high performance can be achieved with a fully earth-abundant and low-toxicity materials set. A systematic screening of back contacts, Se phases, absorber thickness, protective overlayers, and electrolyte formulations revealed the crucial role of Mo in enhancing Se orientation, charge extraction, and photovoltage generation. These results establish multiple benchmarks for Se-based PEC water splitting and highlight the potential of streamlined and scalable architectures for efficient and sustainable green hydrogen production.
- Open Access
- 23 September 2025
- Published by Elsevier in Renewable Energy
- Vol. 256
Transparent solar cells based on a-Si1-xCx:H alloys: from silicon to carbon-rich absorbers
- 23 September 2025
- Published by Elsevier in Renewable Energy
- Vol. 256
Open AccessTransparent solar cells based on a-Si1-xCx:H alloys: from silicon to carbon-rich absorbers
- Open Access
- 1 July 2025
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 13 (31) , 25498-25508
Strategies for back contact engineering in high-performance flexible kesterite solar cells
Back contact engineering of flexible (Ag,Cu)2ZnSn(S,Se)4 solar cells on Mo foil was performed. Despite the formation of a thick MoSe2 layer, MoO3 insertion at the back reduced kesterite decomposition and promoted grain growth, enabling η of 11.2%.
- 1 July 2025
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 13 (31) , 25498-25508
Open AccessStrategies for back contact engineering in high-performance flexible kesterite solar cells
Back contact engineering of flexible (Ag,Cu)2ZnSn(S,Se)4 solar cells on Mo foil was performed. Despite the formation of a thick MoSe2 layer, MoO3 insertion at the back reduced kesterite decomposition and promoted grain growth, enabling η of 11.2%.
- Open Access
Exploring the Limits and Balancing Efficiency, Transparency, and Esthetics in Ultrathin a‐Si:H Transparent Photovoltaic Devices
Transparent photovoltaic (TPV) devices represent a promising advance in photovoltaic technologies, particularly in building‐integrated photovoltaics (BIPV). Unlike conventional photovoltaics, which primarily prioritize efficiency, TPV must balance between efficiency, transparency, and aesthetics. These additional dimensions introduce unique challenges on device architecture. This article reports the development of wide‐bandgap, inorganic‐based TPV devices integrating ultrathin hydrogenated amorphous silicon (a‐Si:H) as a transparent absorber, with carrier selective contacts and transparent electrodes. The article analyzes how absorber thickness influences the electrical, optical, and aesthetic performance of devices, evaluating key parameters in TPV such as light utilization efficiency (LUE), average photopic transmittance (APT), color rendering index (CRI), and electrical properties such as power conversion efficiency (PCE). The device structure is SLG/FTO/AZO/a‐SiCx(n)/a‐Si:H/V2Ox/AZO. This approach results in PCE ranging from 1.7% with an APT of 60% to a PCE of 4.1% with an APT of 28%, yielding LUE values between 0.9% and 1.3%. Device characterization encompasses optical spectrophotometry, J–V measurements under standard test conditions, spectral response analysis, and variable illumination measurements (VIM). Additionally, color characterization is conducted using CIE 1931 color space maps to determine the chromaticity coordinates, CRI, and the variation of color as a function of absorber thickness.
Open AccessExploring the Limits and Balancing Efficiency, Transparency, and Esthetics in Ultrathin a‐Si:H Transparent Photovoltaic Devices
Transparent photovoltaic (TPV) devices represent a promising advance in photovoltaic technologies, particularly in building‐integrated photovoltaics (BIPV). Unlike conventional photovoltaics, which primarily prioritize efficiency, TPV must balance between efficiency, transparency, and aesthetics. These additional dimensions introduce unique challenges on device architecture. This article reports the development of wide‐bandgap, inorganic‐based TPV devices integrating ultrathin hydrogenated amorphous silicon (a‐Si:H) as a transparent absorber, with carrier selective contacts and transparent electrodes. The article analyzes how absorber thickness influences the electrical, optical, and aesthetic performance of devices, evaluating key parameters in TPV such as light utilization efficiency (LUE), average photopic transmittance (APT), color rendering index (CRI), and electrical properties such as power conversion efficiency (PCE). The device structure is SLG/FTO/AZO/a‐SiCx(n)/a‐Si:H/V2Ox/AZO. This approach results in PCE ranging from 1.7% with an APT of 60% to a PCE of 4.1% with an APT of 28%, yielding LUE values between 0.9% and 1.3%. Device characterization encompasses optical spectrophotometry, J–V measurements under standard test conditions, spectral response analysis, and variable illumination measurements (VIM). Additionally, color characterization is conducted using CIE 1931 color space maps to determine the chromaticity coordinates, CRI, and the variation of color as a function of absorber thickness.
- Open Access
- 1 March 2024
- Published by Elsevier in Journal of Science: Advanced Materials and Devices
- Vol. 9 (2)
Impact of atomic layer deposition temperature on electrical and optical properties of ZnO:Al films
- 1 March 2024
- Published by Elsevier in Journal of Science: Advanced Materials and Devices
- Vol. 9 (2)
Open AccessImpact of atomic layer deposition temperature on electrical and optical properties of ZnO:Al films