Yang Liu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Yang Liu has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Bing Dai
Anhui Key Laboratory of Low Carbon Metallurgy and Solid Waste Resource Utilization, Anhui University of Technology, Ma’anshan 243002, China
1 shared publication - Hao He
Anhui Key Laboratory of Low Carbon Metallurgy and Solid Waste Resource Utilization, Anhui University of Technology, Ma’anshan 243002, China
1 shared publication - Huaqin Huang
Anhui Engineering Research Center of Low-Carbon Metallurgy and Process Control, Anhui University of Technology, Maanshan, China
1 shared publication - Junjie Ma
Anhui Key Laboratory of Low Carbon Metallurgy and Solid Waste Resource Utilization, Anhui University of Technology, Ma’anshan 243002, China
1 shared publication - Kaixuan Li
Anhui International Joint Research Center for Metallurgical Processes and Systems Science, Anhui University of Technology, Ma’anshan 243002, China
1 shared publication - Peisheng Lyu
School of Metallurgy and Environment, Central South University, Changsha, P.R. China
1 shared publication
Latest Publications
- Open Access
Regulation of Interface Compatibility and Performance in Soft Magnetic Composites with Inorganic Insulation Layers by FePO4 Intermediate Transition Layer
In the fabrication of soft magnetic composites, the lattice mismatch between the inorganic insulation layer and the iron matrix often leads to the formation of cracks during the molding process, which significantly impairs the operational performance of the materials. Consequently, it is imperative to develop novel strategies for inorganic insulation coatings that offer high electrical resistivity and thermal stability and are less susceptible to cracking during formation. This paper presents a new structure for soft magnetic composites that incorporates FePO4 as an intermediate transition layer between the iron-based soft magnetic particles and the inorganic ceramic insulation layer. This configuration is designed to provide insulation coatings with superior voltage and thermal resistance, as well as high electrical resistivity. The research details the processes forming the FePO4 intermediate transition layer and the SiO2 insulation layer on the iron powder surface, along with their interaction mechanisms. An analysis comparing the scenarios with and without the FePO4 intermediate transition layer shows its beneficial impact on the magnetic properties and mechanical strength of the soft magnetic composites. Further investigations reveal that at a phosphoric acid concentration of 1 wt.%, the FePO4 layer significantly enhances the interface compatibility between the Fe powder matrix and the SiO2 insulation layer. Under these conditions, the Fe@ FePO4/SiO2 soft magnetic composites demonstrate outstanding overall performance: the saturation magnetization stands at 215.60 emu/g, effective permeability at 83.2, resistivity at 57.42 Ω·m, power loss at 375.0 kW/m3 under 30 mT/100 kHz, and radial compressive strength at 15.95 Kgf. These findings offer novel insights and practical approaches for advancing inorganic insulation coating strategies and provide vital scientific support for further enhancing the magnetic and mechanical properties of soft magnetic composites.
Open AccessRegulation of Interface Compatibility and Performance in Soft Magnetic Composites with Inorganic Insulation Layers by FePO4 Intermediate Transition Layer
In the fabrication of soft magnetic composites, the lattice mismatch between the inorganic insulation layer and the iron matrix often leads to the formation of cracks during the molding process, which significantly impairs the operational performance of the materials. Consequently, it is imperative to develop novel strategies for inorganic insulation coatings that offer high electrical resistivity and thermal stability and are less susceptible to cracking during formation. This paper presents a new structure for soft magnetic composites that incorporates FePO4 as an intermediate transition layer between the iron-based soft magnetic particles and the inorganic ceramic insulation layer. This configuration is designed to provide insulation coatings with superior voltage and thermal resistance, as well as high electrical resistivity. The research details the processes forming the FePO4 intermediate transition layer and the SiO2 insulation layer on the iron powder surface, along with their interaction mechanisms. An analysis comparing the scenarios with and without the FePO4 intermediate transition layer shows its beneficial impact on the magnetic properties and mechanical strength of the soft magnetic composites. Further investigations reveal that at a phosphoric acid concentration of 1 wt.%, the FePO4 layer significantly enhances the interface compatibility between the Fe powder matrix and the SiO2 insulation layer. Under these conditions, the Fe@ FePO4/SiO2 soft magnetic composites demonstrate outstanding overall performance: the saturation magnetization stands at 215.60 emu/g, effective permeability at 83.2, resistivity at 57.42 Ω·m, power loss at 375.0 kW/m3 under 30 mT/100 kHz, and radial compressive strength at 15.95 Kgf. These findings offer novel insights and practical approaches for advancing inorganic insulation coating strategies and provide vital scientific support for further enhancing the magnetic and mechanical properties of soft magnetic composites.
- Open Access
- 30 March 2024
- Published by MDPI AG in Magnetochemistry
- Vol. 10 (4) , 23
Investigating the Effect of Carbonyl Iron Powder Doping on the Microstructure and Magnetic Properties of Soft Magnetic Composites
This study proposes the thermal decomposition of salt compounds and doping of carbonyl iron powders (CIPs) to optimize the preparation of an insulating layer through the solid-phase interface reaction. First, (Fe–Si–Cr + CIPs)/ZnSO4 composite powders were synthesized using the hydrothermal method and (Fe–Si–Cr + CIPs)/ZnO·SiO2·Cr2O3 SMCs with a ZnO·SiO2·Cr2O3 composite insulation layer were prepared through heat treatment and cold pressing. The effect of the CIP doping content on the microstructure and magnetic properties of the (Fe–Si–Cr + CIPs)/ZnO·SiO2·Cr2O3 SMCs were then investigated. During the heat treatment, ZnSO4 decomposed into solid ZnO and gaseous SO2 and O2. The O2 drives the solid-phase reaction, prompting the migration of nonmagnetic Si and Cr atoms from the interior of the Fe–Si–Cr soft magnetic powder to the surface insulation layer, finally forming the ZnO·SiO2·Cr2O3 insulation layer. The doped CIPs also show good plasticity during the coating process, combining with the coating layer to fill the internal pores of SMCs. Moreover, as the particles are small with a high surface area, they increase the number of reaction sites for ZnSO4 decomposition and facilitate the growth of the composite insulation layer, promoting its uniform distribution on the surfaces of the soft magnetic powders and CIPs. The lattice mismatch between the insulation layer and soft magnetic powder is reduced while the magnetic-phase content is increased, allowing the effective doping of CIPs sin the insulation layer. The magnetic properties of SMCs can be precisely regulated by changing the doping amount of CIPs. Unlike other insulating layer–preparation strategies based on the interfacial solid-phase reaction, the proposed method exploits the high plasticity and specific surface area of CIPs and removes the lattice mismatch between the insulation layer and soft magnetic powder.
- 30 March 2024
- Published by MDPI AG in Magnetochemistry
- Vol. 10 (4) , 23
Open AccessInvestigating the Effect of Carbonyl Iron Powder Doping on the Microstructure and Magnetic Properties of Soft Magnetic Composites
This study proposes the thermal decomposition of salt compounds and doping of carbonyl iron powders (CIPs) to optimize the preparation of an insulating layer through the solid-phase interface reaction. First, (Fe–Si–Cr + CIPs)/ZnSO4 composite powders were synthesized using the hydrothermal method and (Fe–Si–Cr + CIPs)/ZnO·SiO2·Cr2O3 SMCs with a ZnO·SiO2·Cr2O3 composite insulation layer were prepared through heat treatment and cold pressing. The effect of the CIP doping content on the microstructure and magnetic properties of the (Fe–Si–Cr + CIPs)/ZnO·SiO2·Cr2O3 SMCs were then investigated. During the heat treatment, ZnSO4 decomposed into solid ZnO and gaseous SO2 and O2. The O2 drives the solid-phase reaction, prompting the migration of nonmagnetic Si and Cr atoms from the interior of the Fe–Si–Cr soft magnetic powder to the surface insulation layer, finally forming the ZnO·SiO2·Cr2O3 insulation layer. The doped CIPs also show good plasticity during the coating process, combining with the coating layer to fill the internal pores of SMCs. Moreover, as the particles are small with a high surface area, they increase the number of reaction sites for ZnSO4 decomposition and facilitate the growth of the composite insulation layer, promoting its uniform distribution on the surfaces of the soft magnetic powders and CIPs. The lattice mismatch between the insulation layer and soft magnetic powder is reduced while the magnetic-phase content is increased, allowing the effective doping of CIPs sin the insulation layer. The magnetic properties of SMCs can be precisely regulated by changing the doping amount of CIPs. Unlike other insulating layer–preparation strategies based on the interfacial solid-phase reaction, the proposed method exploits the high plasticity and specific surface area of CIPs and removes the lattice mismatch between the insulation layer and soft magnetic powder.