Aaron Hardy
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Aaron Hardy has a total of 44 co-authors. Here are the top co-authors by number of shared publications:
- Matthias Muehle
Fraunhofer USA Inc., Center Midwest 4 , East Lansing, Michigan 48824
3 shared publications - Nina Baule
Fraunhofer USA, Inc., Center Midwest 2 , East Lansing, Michigan 48824
2 shared publications A. Glen Birdwell
Army Research Directorate, DEVCOM Army Research Laboratory 2800 Powder Mill Road Adelphi MD 20783‐1138 USA
1 shared publication- Alex Ho
Fraunhofer USA, Inc., Center Midwest 2 , East Lansing, Michigan 48824
1 shared publication Beijia Zhang
Advanced Materials and Microsystems Lincoln Laboratory, Massachusetts Institute of Technology Lexington 244 Wood Street Lexington MA 02421‐6426 USA
1 shared publication- Boon S. Ooi
King Abdullah University of Science and Technology (KAUST)
1 shared publication
Latest Publications
- 4 May 2026
- Published by AIP Publishing in Applied Physics Letters
- Vol. 128 (18)
Preliminary demonstration of diamond-GaN p–n diodes via grafting
Ultrawide bandgap (UWBG) semiconductors exhibit exceptional electrical and thermal properties, offering strong potential for high-power and high-frequency electronics. However, efficient doping in UWBG materials is typically limited to either n-type or p-type, constraining their application to unipolar devices. The realization of p–n junctions through heterogeneous integration of complementary UWBG (or WBG) semiconductors is hindered by lattice mismatch and thermal expansion differences. Here, we report the preliminary demonstration of diamond–GaN heterojunction p–n diodes fabricated via Grafting. A single-crystalline p+ diamond nanomembrane was integrated onto an epitaxially grown c-plane n−/n+ GaN substrate with an ultrathin ALD–Al2O3 interlayer. The resulting diodes exhibit an ideality factor of 1.55 and a rectification ratio of ∼104. Structural and interfacial properties were examined by AFM, XRD, Raman, and STEM, providing critical insights to guide further optimization of diamond–GaN p–n heterojunction devices.
- 4 May 2026
- Published by AIP Publishing in Applied Physics Letters
- Vol. 128 (18)
Preliminary demonstration of diamond-GaN p–n diodes via grafting
Ultrawide bandgap (UWBG) semiconductors exhibit exceptional electrical and thermal properties, offering strong potential for high-power and high-frequency electronics. However, efficient doping in UWBG materials is typically limited to either n-type or p-type, constraining their application to unipolar devices. The realization of p–n junctions through heterogeneous integration of complementary UWBG (or WBG) semiconductors is hindered by lattice mismatch and thermal expansion differences. Here, we report the preliminary demonstration of diamond–GaN heterojunction p–n diodes fabricated via Grafting. A single-crystalline p+ diamond nanomembrane was integrated onto an epitaxially grown c-plane n−/n+ GaN substrate with an ultrathin ALD–Al2O3 interlayer. The resulting diodes exhibit an ideality factor of 1.55 and a rectification ratio of ∼104. Structural and interfacial properties were examined by AFM, XRD, Raman, and STEM, providing critical insights to guide further optimization of diamond–GaN p–n heterojunction devices.
- 1 January 2026
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 97 (1)
High-accuracy [R, T] optical characterization of small-area diamond samples via a custom dual-beam sample holder
We present a custom sample holder system (SHS) enabling high-fidelity reflectance and transmittance ([R, T]) measurements of small (3–7 mm) diamond samples using dual-beam spectrophotometry. Through precision alignment, standard reference material-based correction strategies, and aperture-induced distortion cancellation, the SHS achieves sub-percent absolute photometric accuracy, allowing direct inversion of [R, T] for optical constants [n, k] via a Newton–Raphson (N–R) method. This process eliminates reliance on curve-fitting, instead using branch topology—physical (p-) and mathematical (m-) branch crossings—to extract thickness, roughness, and vertical non-uniformity from fringe behavior. Applied to boron-doped diamond (BDD) homoepitaxial films, the method reduces thickness variance by over 3× compared to mass-gain measurements and reveals carrier density gradients in thin layers consistent with secondary ion mass spectroscopy (SIMS). Notably, ripple-like discontinuities in [n, k]—often dismissed as artifacts—are shown to encode real growth physics. This enables optical retrieval of effective hole mass (∼0.48 m0), carrier lifetime, and depth-dependent doping profiles non-destructively and with nanoscale sensitivity. Beyond diamond, this approach reframes spectrophotometry not as a passive measurement but as an epistemic filter: a falsification engine that tests the adequacy of optical models. Inversion-aware metrology thus enables new modes of structural verification, diagnostic clarity, and growth-process insight across small-scale and high-optical density material systems.
- 1 January 2026
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 97 (1)
High-accuracy [R, T] optical characterization of small-area diamond samples via a custom dual-beam sample holder
We present a custom sample holder system (SHS) enabling high-fidelity reflectance and transmittance ([R, T]) measurements of small (3–7 mm) diamond samples using dual-beam spectrophotometry. Through precision alignment, standard reference material-based correction strategies, and aperture-induced distortion cancellation, the SHS achieves sub-percent absolute photometric accuracy, allowing direct inversion of [R, T] for optical constants [n, k] via a Newton–Raphson (N–R) method. This process eliminates reliance on curve-fitting, instead using branch topology—physical (p-) and mathematical (m-) branch crossings—to extract thickness, roughness, and vertical non-uniformity from fringe behavior. Applied to boron-doped diamond (BDD) homoepitaxial films, the method reduces thickness variance by over 3× compared to mass-gain measurements and reveals carrier density gradients in thin layers consistent with secondary ion mass spectroscopy (SIMS). Notably, ripple-like discontinuities in [n, k]—often dismissed as artifacts—are shown to encode real growth physics. This enables optical retrieval of effective hole mass (∼0.48 m0), carrier lifetime, and depth-dependent doping profiles non-destructively and with nanoscale sensitivity. Beyond diamond, this approach reframes spectrophotometry not as a passive measurement but as an epistemic filter: a falsification engine that tests the adequacy of optical models. Inversion-aware metrology thus enables new modes of structural verification, diagnostic clarity, and growth-process insight across small-scale and high-optical density material systems.
- 30 December 2024
- Published by Wiley in Physica Status Solidi (a)
- Vol. 222 (7)
Low‐Temperature Processing to Obtain Contact Resistance of <0.03 Ohm mm to Boron‐Doped Diamond
Low‐resistance Ohmic contacts are necessary for high‐performance electronic devices. Ultrawide‐bandgap semiconductor materials typically have high‐resistance Ohmic contacts between the metal contact and the semiconductor. For single‐crystal boron‐doped diamond, with a bandgap of 5.5 eV, the reported specific contact resistance values vary from >10−3 Ω cm2 to the lowest reported value of 2 × 10−7 Ω cm2. To obtain this low‐resistance Ohmic contact, a high temperature, >500 °C, annealing is usually required, which can limit fabrication procedures and compromise device designs. On p‐type single‐crystal diamond, the lowest reported contact resistance is 0.39 Ω mm. This article reports specific contact resistances of 8.2 × 10−8 to 3.6 × 10−7 Ω cm2 and contact resistances 0.027 to 0.041 Ω mm, which are significantly better than reports in the literature and are achieved without the annealing step. The results are achieved by reactive ion etching 10 to 20 nm into the boron‐doped diamond surface. After the etch, evaporated Ti/Au forms Ohmic contacts with resistances between 0.08 and 0.2 Ω mm without an anneal. An additional step of exposing the etched surface to an intense H2 plasma at 700 °C before Ti/Au deposition, results in Ohmic contacts between 0.027 and 0.041 Ω mm.
- 30 December 2024
- Published by Wiley in Physica Status Solidi (a)
- Vol. 222 (7)
Low‐Temperature Processing to Obtain Contact Resistance of <0.03 Ohm mm to Boron‐Doped Diamond
Low‐resistance Ohmic contacts are necessary for high‐performance electronic devices. Ultrawide‐bandgap semiconductor materials typically have high‐resistance Ohmic contacts between the metal contact and the semiconductor. For single‐crystal boron‐doped diamond, with a bandgap of 5.5 eV, the reported specific contact resistance values vary from >10−3 Ω cm2 to the lowest reported value of 2 × 10−7 Ω cm2. To obtain this low‐resistance Ohmic contact, a high temperature, >500 °C, annealing is usually required, which can limit fabrication procedures and compromise device designs. On p‐type single‐crystal diamond, the lowest reported contact resistance is 0.39 Ω mm. This article reports specific contact resistances of 8.2 × 10−8 to 3.6 × 10−7 Ω cm2 and contact resistances 0.027 to 0.041 Ω mm, which are significantly better than reports in the literature and are achieved without the annealing step. The results are achieved by reactive ion etching 10 to 20 nm into the boron‐doped diamond surface. After the etch, evaporated Ti/Au forms Ohmic contacts with resistances between 0.08 and 0.2 Ω mm without an anneal. An additional step of exposing the etched surface to an intense H2 plasma at 700 °C before Ti/Au deposition, results in Ohmic contacts between 0.027 and 0.041 Ω mm.
- 29 March 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Semiconductor Manufacturing
- Vol. 37 (2) , 190-198
Chemical Mechanical Polishing of Single-Crystalline Diamond Epitaxial Layers for Electronics Applications
For single crystal diamond (SCD) to gain practical use in technical applications including solid state electronics, thin (<1 μm), doped epitaxial SCD layers with very low (<1 nm) surface roughness are required. Conventional SCD chemical mechanical polishing (CMP) processes are insufficient to meet the requirements of such applications because the material removal rate (MRR) is often characterized inappropriately, and the material removal uniformity is seldom considered. In this study, chemical vapor deposition (CVD) growth of two lightly boron doped (p-) epilayers was performed on 3misoriented (100) high pressure high temperature substrates of 4.5 x 4.5 mm2 area. A subsequent 8-hour oxidative CMP process utilizing potassium permanganate and a novel self-leveling holder design decreased the average surface roughness from 3.83 nm and 1.57 nm to 0.20 nm and 0.16 nm for the two samples, respectively. MRRs were determined by evaluating five circular wear monitor structures in each sample by atomic force microscopy before and after the CMP process. The average MRRs were found to be 38.6 nm/hr and 37.3 nm/hr for the two samples. The purpose of this study is to demonstrate a CMP process suitable for polishing thin SCD epilayers to meet the needs of solid-state electronics applications.
- 29 March 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Semiconductor Manufacturing
- Vol. 37 (2) , 190-198
Chemical Mechanical Polishing of Single-Crystalline Diamond Epitaxial Layers for Electronics Applications
For single crystal diamond (SCD) to gain practical use in technical applications including solid state electronics, thin (<1 μm), doped epitaxial SCD layers with very low (<1 nm) surface roughness are required. Conventional SCD chemical mechanical polishing (CMP) processes are insufficient to meet the requirements of such applications because the material removal rate (MRR) is often characterized inappropriately, and the material removal uniformity is seldom considered. In this study, chemical vapor deposition (CVD) growth of two lightly boron doped (p-) epilayers was performed on 3misoriented (100) high pressure high temperature substrates of 4.5 x 4.5 mm2 area. A subsequent 8-hour oxidative CMP process utilizing potassium permanganate and a novel self-leveling holder design decreased the average surface roughness from 3.83 nm and 1.57 nm to 0.20 nm and 0.16 nm for the two samples, respectively. MRRs were determined by evaluating five circular wear monitor structures in each sample by atomic force microscopy before and after the CMP process. The average MRRs were found to be 38.6 nm/hr and 37.3 nm/hr for the two samples. The purpose of this study is to demonstrate a CMP process suitable for polishing thin SCD epilayers to meet the needs of solid-state electronics applications.