Yasir M. F. Mukhtar
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Yasir M. F. Mukhtar has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Elhassan Mostafa Abdallah
Faculty of Engineering Technology and Built Environment, UCSI University, Kuala Lumpur, Malaysia
4 shared publications Faleh H. Almahdawi
Petroleum Engineering Department, College of Engineering, University of Baghdad, Iraq
1 shared publicationFarhana Sultana
Faculty of Engineering Technology and Built Environment, UCSI University, Kuala Lumpur, Malaysia
1 shared publication- Mohd Azraai Miswan
UCSI University
1 shared publication - Nada Ahmed Abbas Ahmed Malek
UCSI University
1 shared publication Nader Mohamed
Faculty of Engineering Technology and Built Environment, UCSI University, Kuala Lumpur, Malaysia
1 shared publication
Latest Publications
- Open Access
- 1 October 2023
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 2594 (1) , 012026
Analysis of Well Performance Based on Bottom Hole Pressure Calculations for Gas Lift Application
This paper focuses on optimizing gas lift techniques in four wells located in the North Sea to overcome the common issue of low reservoir pressure. Gas lift is a common artificial lift technique used in wells with low reservoir pressure where the natural pressure of the reservoir is insufficient to bring the oil to the surface. The success of gas lift optimization depends on identifying the deepest injection point, gas injection rate, and pressure of the gas injected. The paper proposes the deepest injection points for wells A-03, A-09A, A-10T2, and A-12BT2 as 3809.38 ft, 6649.7 ft, 3559.88 ft, and 3979.04 ft, respectively. The injection rates analyzed in this paper range from 1-10 mmscf/day, and injection pressures of 500 psia, 1000 psia, and 1500 psia were used. The response of each well to gas lift was analyzed, and increasing injection rate and pressure were found to increase oil production rate. The optimal gas injection rate and pressure for wells A-03, A-09A, and A-12BT2 were found to be 10 mmscf/day and 1500 psia, while for well A-12BT2, the best oil recovery was obtained at an injection rate of 3 mmcsf/day and injection pressure of 1500 psia. Tubing size within the range of 1-5.5 inch was examined, and it was found that increasing tubing size enhances oil flow rate. The optimal tubing size for the wells was found to be 5.5 inch, taking into consideration factors such as flow rate, pressure, temperature requirements, and fluid type.
- 1 October 2023
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 2594 (1) , 012026
Open AccessAnalysis of Well Performance Based on Bottom Hole Pressure Calculations for Gas Lift Application
This paper focuses on optimizing gas lift techniques in four wells located in the North Sea to overcome the common issue of low reservoir pressure. Gas lift is a common artificial lift technique used in wells with low reservoir pressure where the natural pressure of the reservoir is insufficient to bring the oil to the surface. The success of gas lift optimization depends on identifying the deepest injection point, gas injection rate, and pressure of the gas injected. The paper proposes the deepest injection points for wells A-03, A-09A, A-10T2, and A-12BT2 as 3809.38 ft, 6649.7 ft, 3559.88 ft, and 3979.04 ft, respectively. The injection rates analyzed in this paper range from 1-10 mmscf/day, and injection pressures of 500 psia, 1000 psia, and 1500 psia were used. The response of each well to gas lift was analyzed, and increasing injection rate and pressure were found to increase oil production rate. The optimal gas injection rate and pressure for wells A-03, A-09A, and A-12BT2 were found to be 10 mmscf/day and 1500 psia, while for well A-12BT2, the best oil recovery was obtained at an injection rate of 3 mmcsf/day and injection pressure of 1500 psia. Tubing size within the range of 1-5.5 inch was examined, and it was found that increasing tubing size enhances oil flow rate. The optimal tubing size for the wells was found to be 5.5 inch, taking into consideration factors such as flow rate, pressure, temperature requirements, and fluid type.
- Open Access
- 1 October 2023
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 2594 (1) , 012042
Development of Predictive Model for Wax Formation in Deep-water Pipeline Using Machine learning
Wax deposition in deep sea pipelines can affect oil and gas production. It happens when the pipeline temperature drops below the wax appearance temperature, causing the wax to solidify and stick to the pipeline walls. This paper discusses the limitations of current models in predicting wax deposition in pipelines and proposes the development of more complex, intelligent models that are accurate, resilient, and adaptable to novel input-output scenarios. It also highlights various methods for preventing wax deposition, including the use of chemical inhibitors and thermal remediation techniques. The paper aims to develop a neural network modeling approach for predicting wax deposition potential in producing reservoirs to prevent accumulation before removal. The parameters that were used are wax molecule concentration gradient at pipe wall, temperature gradient at pipe wall, reported wax deposition rate, the pipe wall shear stress, and crude oil viscosity. The radial basis function neural network (RBFNN), is based on the machine learning technique. RBFNN is a good choice for building a predictive wax deposition rate model because it is highly accurate, robust to noise and outliers, computationally efficient, can model complex nonlinear relationships, suitable for real-time applications and requires less training data. The RBF neural network is constructed using MATLAB. The outcomes and experimental data are consistent with a 1.5 percent relative inaccuracy when compared to prior studies. The R^2 value was 0.9906, R value was 0.9953 and the RMSE value was 0.8598. The RBF neural network-based approach for predicting wax deposition rate was successful.
- 1 October 2023
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 2594 (1) , 012042
Open AccessDevelopment of Predictive Model for Wax Formation in Deep-water Pipeline Using Machine learning
Wax deposition in deep sea pipelines can affect oil and gas production. It happens when the pipeline temperature drops below the wax appearance temperature, causing the wax to solidify and stick to the pipeline walls. This paper discusses the limitations of current models in predicting wax deposition in pipelines and proposes the development of more complex, intelligent models that are accurate, resilient, and adaptable to novel input-output scenarios. It also highlights various methods for preventing wax deposition, including the use of chemical inhibitors and thermal remediation techniques. The paper aims to develop a neural network modeling approach for predicting wax deposition potential in producing reservoirs to prevent accumulation before removal. The parameters that were used are wax molecule concentration gradient at pipe wall, temperature gradient at pipe wall, reported wax deposition rate, the pipe wall shear stress, and crude oil viscosity. The radial basis function neural network (RBFNN), is based on the machine learning technique. RBFNN is a good choice for building a predictive wax deposition rate model because it is highly accurate, robust to noise and outliers, computationally efficient, can model complex nonlinear relationships, suitable for real-time applications and requires less training data. The RBF neural network is constructed using MATLAB. The outcomes and experimental data are consistent with a 1.5 percent relative inaccuracy when compared to prior studies. The R^2 value was 0.9906, R value was 0.9953 and the RMSE value was 0.8598. The RBF neural network-based approach for predicting wax deposition rate was successful.
- 11 May 2023
- Published by Springer Nature
- p. 120-132
Analysis of Drilling Trajectory and Casing Design for Straight and Deviated Wells in a Malaysian Oil Field
- 11 May 2023
- Published by Springer Nature
- p. 120-132
Analysis of Drilling Trajectory and Casing Design for Straight and Deviated Wells in a Malaysian Oil Field
- 11 May 2023
- Published by Springer Nature
- p. 106-119
Application of Multilateral Wells to Increase Well Productivity in Offshore Oil Field Case Study
- 11 May 2023
- Published by Springer Nature
- p. 106-119
Application of Multilateral Wells to Increase Well Productivity in Offshore Oil Field Case Study