Kaiwei Tian
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Kaiwei Tian has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Ning Tian
Powerchina Northwest Engineering Corporation Limited, Xi’an 710100, China
3 shared publications Ningxi Zhou
Institute of Rock and Soil Mechanics, Chinese Academy of Sciences, Wuhan, China
2 shared publicationsQian Sheng
Institute of Rock and Soil Mechanics, Chinese Academy of Sciences, Wuhan, China
2 shared publications- Zeqi Zhu
State Key Laboratory of Geomechanics and Geotechnical Engineering, Institute of Rock and Soil Mechanics, Chinese Academy of Sciences, Wuhan 430071, China
2 shared publications - Jian Chen
State Key Laboratory of Geomechanics and Geotechnical Engineering, Institute of Rock and Soil Mechanics, Chinese Academy of Sciences, Wuhan, China
1 shared publication - Juehao Huang
State Key Laboratory of Geomechanics and Geotechnical Engineering Safety, Institute of Rock and Soil Mechanics, Chinese Academy of Sciences, Wuhan 430071, China
1 shared publication
Latest Publications
- 26 June 2025
- Published by Springer Nature in Rock Mechanics and Rock Engineering
- Vol. 58 (11) , 12137-12162
The Impact of Petrographic Characteristics on Granite Strength: Insights from an Interpretable Machine Learning Model
- 26 June 2025
- Published by Springer Nature in Rock Mechanics and Rock Engineering
- Vol. 58 (11) , 12137-12162
The Impact of Petrographic Characteristics on Granite Strength: Insights from an Interpretable Machine Learning Model
- Open Access
Calibration of Discrete Element Method Parameters for a High-Fidelity Lunar Regolith Simulant Considering the Effects of Realistic Particle Shape
The Discrete Element Method (DEM) is an important tool for investigating the geotechnical properties of lunar regolith. The accuracy of DEM simulations largely depends on precise particle modeling and the appropriate selection of mesoscopic parameters. To enhance the reliability and accuracy of the DEM in lunar regolith studies, this paper utilized the high-fidelity IRSM-1 lunar regolith simulant to construct a DEM model with realistic particle shapes and conducted an angle of repose (AoR) simulation test. The optimal DEM parameters were calibrated using a combination of the Plackett–Burman test, steepest ascent test, and Box–Behnken design. The results indicate that the sliding friction coefficient, rolling friction coefficient, and surface energy significantly influence the simulation AoR. By optimizing against the measured AoR using a second-order regression model, the optimal parameter values were determined to be 0.633, 0.401, and 0.2, respectively. Under these optimal parameters, the error between the simulation and experimental AoR was 2.1%. Finally, the calibrated mesoscopic parameters were validated through a lifting cylinder test, showing an error of 6.3% between the simulation and experimental results. The high similarity in the shape of the AoR further confirms the accuracy and reliability of the parameter calibration method. This study provides a valuable reference for future DEM-based research on the mechanical and engineering properties of lunar regolith.
Open AccessCalibration of Discrete Element Method Parameters for a High-Fidelity Lunar Regolith Simulant Considering the Effects of Realistic Particle Shape
The Discrete Element Method (DEM) is an important tool for investigating the geotechnical properties of lunar regolith. The accuracy of DEM simulations largely depends on precise particle modeling and the appropriate selection of mesoscopic parameters. To enhance the reliability and accuracy of the DEM in lunar regolith studies, this paper utilized the high-fidelity IRSM-1 lunar regolith simulant to construct a DEM model with realistic particle shapes and conducted an angle of repose (AoR) simulation test. The optimal DEM parameters were calibrated using a combination of the Plackett–Burman test, steepest ascent test, and Box–Behnken design. The results indicate that the sliding friction coefficient, rolling friction coefficient, and surface energy significantly influence the simulation AoR. By optimizing against the measured AoR using a second-order regression model, the optimal parameter values were determined to be 0.633, 0.401, and 0.2, respectively. Under these optimal parameters, the error between the simulation and experimental AoR was 2.1%. Finally, the calibrated mesoscopic parameters were validated through a lifting cylinder test, showing an error of 6.3% between the simulation and experimental results. The high similarity in the shape of the AoR further confirms the accuracy and reliability of the parameter calibration method. This study provides a valuable reference for future DEM-based research on the mechanical and engineering properties of lunar regolith.
- 23 March 2024
- Published by Elsevier in Computers and Geotechnics
- Vol. 169
A penetration correction contact model involving friction based on Peridynamics
- 23 March 2024
- Published by Elsevier in Computers and Geotechnics
- Vol. 169
A penetration correction contact model involving friction based on Peridynamics
- Open Access
- 13 December 2023
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 11 (12) , 2351
A Novel Deformation Analytical Solution and Constitutive Model for Fractured Rock Masses
In order to study the deformation and stability of a fractured rock mass, existing research suggests that fracture deformation, which is usually obtained by evaluating the equivalent deformation modulus, dominates the deformation of a fractured rock mass. However, this parameter is difficult to obtain in theory and practice, which limits the application of rock mass deformation analysis methods. In order to calculate the deformation of fractured rock masses, the mass of the rock is regarded as a sponge-like material, and it is assumed that the deformation of a water-saturated fractured rock mass under external force load is approximately equal to the net flow of fracture water. Based on this assumption, firstly, the relationship between rock mass deformation and fracture flow is studied through a single-fracture rock mass model. The hydraulic properties of the fracture are characterized by the permeability coefficient, and the fracture deformation in the rock mass is equivalent to the fracture flow. The fracture deformation calculation formula is derived from the fracture hydraulics calculation formula, and this is compared with the measured data. The rationality of the calculation formula was verified. On this basis, the calculation formula for rock mass deformation, including multiple groups of fracture surfaces, is proposed, and the stress-strain constitutive relationship of a complex rock mass is established. The correctness of the calculation method was verified by comparing it with other theoretical calculation results.
- 13 December 2023
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 11 (12) , 2351
Open AccessA Novel Deformation Analytical Solution and Constitutive Model for Fractured Rock Masses
In order to study the deformation and stability of a fractured rock mass, existing research suggests that fracture deformation, which is usually obtained by evaluating the equivalent deformation modulus, dominates the deformation of a fractured rock mass. However, this parameter is difficult to obtain in theory and practice, which limits the application of rock mass deformation analysis methods. In order to calculate the deformation of fractured rock masses, the mass of the rock is regarded as a sponge-like material, and it is assumed that the deformation of a water-saturated fractured rock mass under external force load is approximately equal to the net flow of fracture water. Based on this assumption, firstly, the relationship between rock mass deformation and fracture flow is studied through a single-fracture rock mass model. The hydraulic properties of the fracture are characterized by the permeability coefficient, and the fracture deformation in the rock mass is equivalent to the fracture flow. The fracture deformation calculation formula is derived from the fracture hydraulics calculation formula, and this is compared with the measured data. The rationality of the calculation formula was verified. On this basis, the calculation formula for rock mass deformation, including multiple groups of fracture surfaces, is proposed, and the stress-strain constitutive relationship of a complex rock mass is established. The correctness of the calculation method was verified by comparing it with other theoretical calculation results.
- Open Access
An Anisotropic Peridynamic Model for Simulating Crack Propagation in Isotropic and Anisotropic Rocks
In this work, we present a peridynamic-based simulation method for modeling quasi-static fracture propagation in isotropic and anisotropic rock within the framework of peridynamic least square minimization (PDLSM). The original isotropic elastic PDLSM is further extended to investigate fracture propagation in anisotropic materials in this study. The proposed AN-PDLSM model integrates an anisotropic model in fracture mechanics to analyze the failure process of anisotropic rocks. An important advancement in this research lies in the incorporation of the maximum energy release rate criterion (MERR) into the PDLSM framework for the first time. This enhancement enables accurately determining crack propagation and the associated crack angles. The proposed model utilizes the energy release rate calculated through the J-integral method to assess bond breakage, and it employs a mesh-independent, piecewise linear fracture model to describe crack propagation. The proposed method fully combines the merits of traditional fracture mechanics with the unique capabilities of peridynamics. To demonstrate the effectiveness of the proposed model, a simulation of fracture evolution in isotropic plates subjected to semi-circular bending tests is presented and compared with experimental results. It is shown that the proposed model accurately replicates fracture trajectories in isotropic specimens. In the context of anisotropic rock, the effect of a weak coefficient on crack morphology is discussed in order to obtain a suitable value. Additionally, the impact of bedding angles on fracture paths through our proposed model is also explored, revealing excellent agreement with experimental results. The findings in this research demonstrate that the proposed AN-PDLSM model is exceptionally proficient at capturing the intricate, oscillating crack paths observed in anisotropic rock materials.
Open AccessAn Anisotropic Peridynamic Model for Simulating Crack Propagation in Isotropic and Anisotropic Rocks
In this work, we present a peridynamic-based simulation method for modeling quasi-static fracture propagation in isotropic and anisotropic rock within the framework of peridynamic least square minimization (PDLSM). The original isotropic elastic PDLSM is further extended to investigate fracture propagation in anisotropic materials in this study. The proposed AN-PDLSM model integrates an anisotropic model in fracture mechanics to analyze the failure process of anisotropic rocks. An important advancement in this research lies in the incorporation of the maximum energy release rate criterion (MERR) into the PDLSM framework for the first time. This enhancement enables accurately determining crack propagation and the associated crack angles. The proposed model utilizes the energy release rate calculated through the J-integral method to assess bond breakage, and it employs a mesh-independent, piecewise linear fracture model to describe crack propagation. The proposed method fully combines the merits of traditional fracture mechanics with the unique capabilities of peridynamics. To demonstrate the effectiveness of the proposed model, a simulation of fracture evolution in isotropic plates subjected to semi-circular bending tests is presented and compared with experimental results. It is shown that the proposed model accurately replicates fracture trajectories in isotropic specimens. In the context of anisotropic rock, the effect of a weak coefficient on crack morphology is discussed in order to obtain a suitable value. Additionally, the impact of bedding angles on fracture paths through our proposed model is also explored, revealing excellent agreement with experimental results. The findings in this research demonstrate that the proposed AN-PDLSM model is exceptionally proficient at capturing the intricate, oscillating crack paths observed in anisotropic rock materials.