Danielle R. Levin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Danielle R. Levin has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Gulzhan Aldan
University of Pennsylvania
2 shared publications - Igor Bargatin
University of Pennsylvania
2 shared publications - Matthew F. Campbell
Department of Mechanical Engineering and Applied Mechanics, University of Pennsylvania, Philadelphia, PA, USA
2 shared publications - Orevaoghene H. Omodior
University of Pennsylvania
1 shared publication Zhipeng Lu
Department of Chemistry, University of Pennsylvania, Philadelphia, Pennsylvania, USA
1 shared publication
Latest Publications
- 1 September 2026
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 18 (36) , 48946-48955
Robust Layered Thermal Insulator Film Stacks for Vacuum Applications
There is a need for mechanically robust, thin thermal insulators within lunar infrastructure to achieve a sustained presence on the Moon. Existing solutions, including aerogels, multilayer insulation, and vacuum insulation panels, often fail to meet these criteria because they are mechanically inflexible and may thermally short or structurally fail upon accidental impact. To bridge this gap, we report high-layer density (nominally 80 to 400 layers/mm) alumina-coated biaxially oriented polyethylene terephthalate (BoPET or Mylar) sheet stacks as a model system for mechanically robust, flexible, low-conductivity thermal insulation in vacuum environments, with potential relevance to lunar applications. Our measurements reveal that stacks consisting of single- and double-sided atomic layer deposited alumina-coated 2.5, 5, and 12.5 μm thick BoPET films, have thermal conductivities as low as 2.2 mW m–1 K–1 at 0.1 MPa applied compressive stress and temperatures from 35 to 120 °C. They can withstand much larger compressive stresses (>20 MPa in separate mechanical testing) than aerogels or uncoated layered insulators without significant degradation of mechanical or thermal properties within the studied temperature range. HyLIFS are promising vacuum insulation candidates that combine the mW m–1 K–1-scale thermal conductivity of vacuum aerogels and vacuum insulation packages with much higher mechanical robustness (flexibility and compressive strength). Our thermal modeling indicates that the dominant heat transfer mechanism in vacuum is spot conduction through antiblocking particles embedded in BoPET, with strongest agreement at higher compressive stresses, suggesting pathways by which even lower conductivities could be achieved.
- 1 September 2026
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 18 (36) , 48946-48955
Robust Layered Thermal Insulator Film Stacks for Vacuum Applications
There is a need for mechanically robust, thin thermal insulators within lunar infrastructure to achieve a sustained presence on the Moon. Existing solutions, including aerogels, multilayer insulation, and vacuum insulation panels, often fail to meet these criteria because they are mechanically inflexible and may thermally short or structurally fail upon accidental impact. To bridge this gap, we report high-layer density (nominally 80 to 400 layers/mm) alumina-coated biaxially oriented polyethylene terephthalate (BoPET or Mylar) sheet stacks as a model system for mechanically robust, flexible, low-conductivity thermal insulation in vacuum environments, with potential relevance to lunar applications. Our measurements reveal that stacks consisting of single- and double-sided atomic layer deposited alumina-coated 2.5, 5, and 12.5 μm thick BoPET films, have thermal conductivities as low as 2.2 mW m–1 K–1 at 0.1 MPa applied compressive stress and temperatures from 35 to 120 °C. They can withstand much larger compressive stresses (>20 MPa in separate mechanical testing) than aerogels or uncoated layered insulators without significant degradation of mechanical or thermal properties within the studied temperature range. HyLIFS are promising vacuum insulation candidates that combine the mW m–1 K–1-scale thermal conductivity of vacuum aerogels and vacuum insulation packages with much higher mechanical robustness (flexibility and compressive strength). Our thermal modeling indicates that the dominant heat transfer mechanism in vacuum is spot conduction through antiblocking particles embedded in BoPET, with strongest agreement at higher compressive stresses, suggesting pathways by which even lower conductivities could be achieved.
- 9 April 2024
- Published by American Physical Society (APS) in Physical Review Applied
- Vol. 21 (4) , 044019
Lightweight photophoretic flyers with germanium coatings as selective absorbers
The goal of ultrathin lightweight photophoretic flyers, or light flyers for short, is to levitate continuously in Earth’s upper atmosphere using only sunlight for propulsive power. We previously reported light flyers that levitated by utilizing differences in thermal accommodation coefficient between the top and bottom of a thin film, made possible by coating their lower surfaces with carbon nanotubes (CNTs). Such designs, though successful, had relatively high thermal emissivity (>0.5), which prevented them from achieving high temperatures and resulted in their transferring relatively low amounts of momentum to the surrounding gas. To address this issue, we have developed light flyers with ultrathin undoped germanium layers that selectively absorb nearly 80% of visible light but are mostly transparent in the thermal infrared, with an average thermal emissivity of <0.1. Our experiments show that germanium-coated light flyers could levitate at up to 43% lower light irradiances than mylar-CNT disks with identical sizes. In addition, we simulated our experiments using a semiempirical model, which allowed us to predict that our 2-cm-diameter disk-shaped germanium-coated light flyers can levitate in the mesosphere (altitudes 67–75 km) under the natural sunlight (1.36 kW/). Similar ultrathin selective-absorber coatings can also be applied to three-dimensional light flyers shaped like solar balloons, allowing them to carry significant payloads and thereby revolutionize long-term atmospheric exploration of Earth or Mars.- 9 April 2024
- Published by American Physical Society (APS) in Physical Review Applied
- Vol. 21 (4) , 044019
Lightweight photophoretic flyers with germanium coatings as selective absorbers
The goal of ultrathin lightweight photophoretic flyers, or light flyers for short, is to levitate continuously in Earth’s upper atmosphere using only sunlight for propulsive power. We previously reported light flyers that levitated by utilizing differences in thermal accommodation coefficient between the top and bottom of a thin film, made possible by coating their lower surfaces with carbon nanotubes (CNTs). Such designs, though successful, had relatively high thermal emissivity (>0.5), which prevented them from achieving high temperatures and resulted in their transferring relatively low amounts of momentum to the surrounding gas. To address this issue, we have developed light flyers with ultrathin undoped germanium layers that selectively absorb nearly 80% of visible light but are mostly transparent in the thermal infrared, with an average thermal emissivity of <0.1. Our experiments show that germanium-coated light flyers could levitate at up to 43% lower light irradiances than mylar-CNT disks with identical sizes. In addition, we simulated our experiments using a semiempirical model, which allowed us to predict that our 2-cm-diameter disk-shaped germanium-coated light flyers can levitate in the mesosphere (altitudes 67–75 km) under the natural sunlight (1.36 kW/). Similar ultrathin selective-absorber coatings can also be applied to three-dimensional light flyers shaped like solar balloons, allowing them to carry significant payloads and thereby revolutionize long-term atmospheric exploration of Earth or Mars.