Shiyun Lin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Shiyun Lin has a total of 22 co-authors. Here are the top co-authors by number of shared publications:
Dagang Yin
School of Science Shandong Jiaotong University Jinan China
10 shared publicationsYuhuan Du
School of Aeronautics Chongqing Jiaotong University Chongqing China
7 shared publications- Donghang Jie
School of Aeronautics Chongqing Jiaotong University Chongqing China
6 shared publications Menghao Ran
School of Aeronautics Chongqing Jiaotong University Chongqing China
5 shared publicationsChenyun Peng
4 shared publicationsJie Bai
School of Aeronautics Chongqing Jiaotong University Chongqing China
4 shared publications
Latest Publications
- 21 July 2026
- Published by Wiley in Fatigue & Fracture of Engineering Materials & Structures
- Vol. 49 (10) , 4086-4098
Parametric Investigation of Reentrant Hexagonal Auxetic Honeycombs Under Tension Mechanical Response and Fractal Characterization of Crack Paths
Auxetic structures with negative Poisson's ratio show promise in aerospace, automotive, and healthcare applications due to their energy absorption and impact resistance. However, most studies focus on compression, leaving tensile deformation mechanisms underexplored. This work investigates reentrant hexagonal auxetic structures with varying strut ratios (2, 2.5, 3) and reentrant angles (40°–80°), fabricated via FDM 3D printing using PLA. Uniaxial tensile tests and finite element simulations were performed to evaluate stress–strain behavior, Poisson's ratio evolution, and failure. Fractal theory quantified crack paths. Results show that increasing strut ratio raises maximum stress but reduces fracture strain. Larger reentrant angles decrease modulus and maximum stress while increasing fracture strain. Energy absorption peaks at 50°–60°. Fractal dimension reveals complex crack paths at 50°–70°, corresponding to optimal absorption. This study elucidates the coupled effects of strut ratio and reentrant angle on tensile behavior, offering insights for multiparameter optimization of auxetic structures.
- 21 July 2026
- Published by Wiley in Fatigue & Fracture of Engineering Materials & Structures
- Vol. 49 (10) , 4086-4098
Parametric Investigation of Reentrant Hexagonal Auxetic Honeycombs Under Tension Mechanical Response and Fractal Characterization of Crack Paths
Auxetic structures with negative Poisson's ratio show promise in aerospace, automotive, and healthcare applications due to their energy absorption and impact resistance. However, most studies focus on compression, leaving tensile deformation mechanisms underexplored. This work investigates reentrant hexagonal auxetic structures with varying strut ratios (2, 2.5, 3) and reentrant angles (40°–80°), fabricated via FDM 3D printing using PLA. Uniaxial tensile tests and finite element simulations were performed to evaluate stress–strain behavior, Poisson's ratio evolution, and failure. Fractal theory quantified crack paths. Results show that increasing strut ratio raises maximum stress but reduces fracture strain. Larger reentrant angles decrease modulus and maximum stress while increasing fracture strain. Energy absorption peaks at 50°–60°. Fractal dimension reveals complex crack paths at 50°–70°, corresponding to optimal absorption. This study elucidates the coupled effects of strut ratio and reentrant angle on tensile behavior, offering insights for multiparameter optimization of auxetic structures.
- 16 July 2026
- Published by Wiley in Polymer Composites
- Vol. 47 (19) , 17461-17472
Low‐Cost Fabrication of Re‐Entrant Carbon‐Fiber Auxetic Composites With Continuous and Discontinuous Fiber Performance
Structures with negative Poisson's ratio hold significant application potential in aerospace and related fields due to their unique auxetic behavior, yet conventional fabrication methods are often costly and complex. To overcome these limitations, this study employs 3D printing to fabricate PLA molds for producing continuous and discontinuous carbon fiber‐reinforced composites with re‐entrant honeycomb architectures. Through systematic tensile testing, scanning electron microscopy (SEM), and finite element analysis (FEA), the mechanical responses and failure mechanisms of the two composite types were comparatively examined. Tensile results show that the continuous fiber specimens (CFS) have a failure strain of 0.74%, and an energy absorption of 0.17 MJ; the corresponding values for the discontinuous fiber specimens (DFS) are 0.68%, and 0.13 MJ, respectively. Compared with DFS, CFS exhibit an approximately 30.8% increase in energy absorption, along with slight improvements in failure strain. The peak stress of DFS (36.79 MPa) is higher than that of CFS (34.15 MPa). Continuous‐fiber composites display multi‐stage load‐bearing behavior, enhanced toughness, and superior energy absorption capacity, with markedly higher stress levels in both the fibers and the matrix compared to their discontinuous‐fiber counterparts. In contrast, discontinuous‐fiber composites demonstrate typical brittle fracture characteristics. Overall, this study provides an effective and low‐cost strategy for the efficient fabrication of high‐performance negative‐Poisson's‐ratio metamaterial structures.
- 16 July 2026
- Published by Wiley in Polymer Composites
- Vol. 47 (19) , 17461-17472
Low‐Cost Fabrication of Re‐Entrant Carbon‐Fiber Auxetic Composites With Continuous and Discontinuous Fiber Performance
Structures with negative Poisson's ratio hold significant application potential in aerospace and related fields due to their unique auxetic behavior, yet conventional fabrication methods are often costly and complex. To overcome these limitations, this study employs 3D printing to fabricate PLA molds for producing continuous and discontinuous carbon fiber‐reinforced composites with re‐entrant honeycomb architectures. Through systematic tensile testing, scanning electron microscopy (SEM), and finite element analysis (FEA), the mechanical responses and failure mechanisms of the two composite types were comparatively examined. Tensile results show that the continuous fiber specimens (CFS) have a failure strain of 0.74%, and an energy absorption of 0.17 MJ; the corresponding values for the discontinuous fiber specimens (DFS) are 0.68%, and 0.13 MJ, respectively. Compared with DFS, CFS exhibit an approximately 30.8% increase in energy absorption, along with slight improvements in failure strain. The peak stress of DFS (36.79 MPa) is higher than that of CFS (34.15 MPa). Continuous‐fiber composites display multi‐stage load‐bearing behavior, enhanced toughness, and superior energy absorption capacity, with markedly higher stress levels in both the fibers and the matrix compared to their discontinuous‐fiber counterparts. In contrast, discontinuous‐fiber composites demonstrate typical brittle fracture characteristics. Overall, this study provides an effective and low‐cost strategy for the efficient fabrication of high‐performance negative‐Poisson's‐ratio metamaterial structures.
- 25 June 2026
- Published by Wiley in Polymer Composites
- Vol. 47 (18) , 16463-16480
Ply‐Count Effects on Tensile Performance of FDM 3D ‐Printed Glass Fiber Hexagonal Honeycombs
Continuous fiber‐reinforced 3D printed honeycombs are a core research focus for aerospace lightweight load‐bearing applications. Ply count, a critical design parameter, still lacks systematic quantitative data on its tensile performance regulation rules and underlying failure mechanisms. This study investigates regular hexagonal high‐strength high‐temperature (HSHT) glass fiber‐reinforced Onyx honeycombs fabricated via fused deposition modeling (FDM), combining quasi‐static tensile tests, SEM characterization, and ply‐correlated finite element simulations. Results show increasing ply count improves elastic modulus by 663% and peak tensile stress by 350% within the test range. Energy absorption gains are prominent for 0–16 plies, then narrow sharply for 24 and 40 plies. Failure modes shift sequentially from matrix‐dominated fracture to intermediate‐ply fiber tow co‐fracture, then widespread 40‐ply interfacial debonding, validated by fiber pull‐out statistics. The developed finite element model has a 21.4% range‐normalized root mean square error, qualitatively capturing the overall upward trend in tensile strength with increasing ply count and the diminishing strength returns at high ply counts, offering guidance for composite honeycomb optimization for uses including drone wings.
- 25 June 2026
- Published by Wiley in Polymer Composites
- Vol. 47 (18) , 16463-16480
Ply‐Count Effects on Tensile Performance of FDM 3D ‐Printed Glass Fiber Hexagonal Honeycombs
Continuous fiber‐reinforced 3D printed honeycombs are a core research focus for aerospace lightweight load‐bearing applications. Ply count, a critical design parameter, still lacks systematic quantitative data on its tensile performance regulation rules and underlying failure mechanisms. This study investigates regular hexagonal high‐strength high‐temperature (HSHT) glass fiber‐reinforced Onyx honeycombs fabricated via fused deposition modeling (FDM), combining quasi‐static tensile tests, SEM characterization, and ply‐correlated finite element simulations. Results show increasing ply count improves elastic modulus by 663% and peak tensile stress by 350% within the test range. Energy absorption gains are prominent for 0–16 plies, then narrow sharply for 24 and 40 plies. Failure modes shift sequentially from matrix‐dominated fracture to intermediate‐ply fiber tow co‐fracture, then widespread 40‐ply interfacial debonding, validated by fiber pull‐out statistics. The developed finite element model has a 21.4% range‐normalized root mean square error, qualitatively capturing the overall upward trend in tensile strength with increasing ply count and the diminishing strength returns at high ply counts, offering guidance for composite honeycomb optimization for uses including drone wings.
- 12 May 2026
- Published by Wiley in Polymer Composites
- Vol. 47 (15) , 13891-13909
Heat Treatment Temperature Effects on Three‐Point Bending of 3D ‐Printed Onyx/ HSHT Fiberglass Honeycomb Composites
This study addresses the pressing demand for lightweight unmanned aerial vehicle (UAV) structures through the application of continuous fiber‐reinforced thermoplastics (CFRTs). Regular hexagonal honeycomb structures were fabricated via fused deposition modeling (FDM). To enhance structural performance, systematic heat treatments were applied at 130°C, 150°C, and 170°C. An integrated analytical framework combining crack path fractal dimension quantification, sequential thermo‐mechanically coupled finite element simulations, and experimental bending tests was developed to enable a comprehensive evaluation. The results reveal a non‐monotonic performance trend, wherein the 150°C treatment yields optimal mechanical properties, including the highest elastic modulus, along with significant improvements in strength and interfacial toughness. These enhancements are corroborated by pronounced fiber pull‐out features and an increase in crack path fractal complexity (fractal dimension = 1.594 ± 0.045). Mechanistic analysis indicates that the finite element simulations confirm that the 150°C treatment achieves an optimal balance between matrix crystallization enhancement and residual stress alleviation, whereas treatment at 170°C leads to interfacial degradation. Overall, this work establishes quantitative correlations between fractal geometric characteristics and material performance, elucidates the underlying thermo‐mechanical regulation mechanisms, and provides novel design strategies for the additive manufacturing of high‐integrity aerospace composite structures.
- 12 May 2026
- Published by Wiley in Polymer Composites
- Vol. 47 (15) , 13891-13909
Heat Treatment Temperature Effects on Three‐Point Bending of 3D ‐Printed Onyx/ HSHT Fiberglass Honeycomb Composites
This study addresses the pressing demand for lightweight unmanned aerial vehicle (UAV) structures through the application of continuous fiber‐reinforced thermoplastics (CFRTs). Regular hexagonal honeycomb structures were fabricated via fused deposition modeling (FDM). To enhance structural performance, systematic heat treatments were applied at 130°C, 150°C, and 170°C. An integrated analytical framework combining crack path fractal dimension quantification, sequential thermo‐mechanically coupled finite element simulations, and experimental bending tests was developed to enable a comprehensive evaluation. The results reveal a non‐monotonic performance trend, wherein the 150°C treatment yields optimal mechanical properties, including the highest elastic modulus, along with significant improvements in strength and interfacial toughness. These enhancements are corroborated by pronounced fiber pull‐out features and an increase in crack path fractal complexity (fractal dimension = 1.594 ± 0.045). Mechanistic analysis indicates that the finite element simulations confirm that the 150°C treatment achieves an optimal balance between matrix crystallization enhancement and residual stress alleviation, whereas treatment at 170°C leads to interfacial degradation. Overall, this work establishes quantitative correlations between fractal geometric characteristics and material performance, elucidates the underlying thermo‐mechanical regulation mechanisms, and provides novel design strategies for the additive manufacturing of high‐integrity aerospace composite structures.
- 24 March 2026
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 143 (22)
Mechanical Behavior and Fractal Analysis of 3D Printing Biomimetic Elliptical Porous PLA Structures
Inspired by lobster claw Bouligand structures, three elliptical PLA porous structures—vertical (V‐EPS), horizontal (H‐EPS), and spiral (S‐EPS)—were fabricated via FDM. Their mechanical responses and stress distributions were systematically assessed via compression and bending tests and FEA. Results show distinct advantages: V‐EPS achieved highest compressive strength and energy absorption; H‐EPS demonstrated superior bending strength. Notably, S‐EPS exhibited the best overall performance, especially in bending energy absorption, despite a 26.9% lower compressive peak stress than V‐EPS. This superiority stems from its unique deformation mechanisms, including efficient stress redistribution and significant crack deflection. Fractal geometry quantified fracture complexity using MATLAB‐derived fractal dimension ( D ). Higher D values indicate more tortuous cracks, and quantitative analysis confirmed a positive correlation between D and macroscopic fracture toughness, implying greater crack complexity enhances energy dissipation. These findings provide a biomimetic design framework for lightweight structures optimized for specific loading modes (compression or bending). Combining biomimicry, PLA materials, and AM offers an effective strategy for lightweight sustainable solutions in aerospace.
- 24 March 2026
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 143 (22)
Mechanical Behavior and Fractal Analysis of 3D Printing Biomimetic Elliptical Porous PLA Structures
Inspired by lobster claw Bouligand structures, three elliptical PLA porous structures—vertical (V‐EPS), horizontal (H‐EPS), and spiral (S‐EPS)—were fabricated via FDM. Their mechanical responses and stress distributions were systematically assessed via compression and bending tests and FEA. Results show distinct advantages: V‐EPS achieved highest compressive strength and energy absorption; H‐EPS demonstrated superior bending strength. Notably, S‐EPS exhibited the best overall performance, especially in bending energy absorption, despite a 26.9% lower compressive peak stress than V‐EPS. This superiority stems from its unique deformation mechanisms, including efficient stress redistribution and significant crack deflection. Fractal geometry quantified fracture complexity using MATLAB‐derived fractal dimension ( D ). Higher D values indicate more tortuous cracks, and quantitative analysis confirmed a positive correlation between D and macroscopic fracture toughness, implying greater crack complexity enhances energy dissipation. These findings provide a biomimetic design framework for lightweight structures optimized for specific loading modes (compression or bending). Combining biomimicry, PLA materials, and AM offers an effective strategy for lightweight sustainable solutions in aerospace.
- 27 August 2025
- Published by Wiley in Polymer Composites
- Vol. 47 (4) , 3665-3681
Regulating Mechanical Behavior of Onyx Hexagonal Honeycombs via Heat Treatment: A Thermo‐Mechanical Study
Additively manufactured honeycomb structures offer exceptional lightweight and high energy‐absorption capabilities for aerospace applications. However, their mechanical performance evolution and damage‐suppression mechanisms under elevated temperatures remain poorly understood. This study bridges a long‐standing gap by combining systematic experiments and thermo‐mechanical finite‐element simulations to quantify the effects of heat‐treatment temperature, post‐treatment cooling duration, and compression‐pretreatment sequence on both microstructural evolution and macroscopic mechanical behavior of FDM‐printed short‐fiber‐reinforced Onyx honeycombs. Five specimen groups underwent heat treatment followed by either 5 or 30 min ambient cooling, with and without 5 mm or 20 mm pre‐compression. Mechanical testing revealed that short‐duration cooling reduced tensile strength by 12.2% and decreased specific energy absorption by 15.3%. Conversely, extended cooling enhanced energy absorption by 275%. Compression pretreatment further increased bearing strength by 13.6%. SEM analysis indicated that heat‐induced thermoplasticization of the nylon matrix strengthened fiber–matrix interfacial bonding, shifted failure modes toward fiber fracture, and that pore coalescence promoted crack deflection and material toughening. Thermo‐mechanical simulations encompassed both stepwise and synchronous loading scenarios, confirming that optimized heat treatment mitigates local stress gradients, and that synchronous loading synergistically compacts defects and stabilizes strain distributions. However, simulations slightly overestimated the strengthening effect in compression‐treated groups due to omission of pore damage. These findings establish a quantitative process–property framework and offer a theoretical foundation for pre‐processing design strategies to optimize the thermo‐mechanical performance and service life of lightweight honeycomb components such as UAV wings.
- 27 August 2025
- Published by Wiley in Polymer Composites
- Vol. 47 (4) , 3665-3681
Regulating Mechanical Behavior of Onyx Hexagonal Honeycombs via Heat Treatment: A Thermo‐Mechanical Study
Additively manufactured honeycomb structures offer exceptional lightweight and high energy‐absorption capabilities for aerospace applications. However, their mechanical performance evolution and damage‐suppression mechanisms under elevated temperatures remain poorly understood. This study bridges a long‐standing gap by combining systematic experiments and thermo‐mechanical finite‐element simulations to quantify the effects of heat‐treatment temperature, post‐treatment cooling duration, and compression‐pretreatment sequence on both microstructural evolution and macroscopic mechanical behavior of FDM‐printed short‐fiber‐reinforced Onyx honeycombs. Five specimen groups underwent heat treatment followed by either 5 or 30 min ambient cooling, with and without 5 mm or 20 mm pre‐compression. Mechanical testing revealed that short‐duration cooling reduced tensile strength by 12.2% and decreased specific energy absorption by 15.3%. Conversely, extended cooling enhanced energy absorption by 275%. Compression pretreatment further increased bearing strength by 13.6%. SEM analysis indicated that heat‐induced thermoplasticization of the nylon matrix strengthened fiber–matrix interfacial bonding, shifted failure modes toward fiber fracture, and that pore coalescence promoted crack deflection and material toughening. Thermo‐mechanical simulations encompassed both stepwise and synchronous loading scenarios, confirming that optimized heat treatment mitigates local stress gradients, and that synchronous loading synergistically compacts defects and stabilizes strain distributions. However, simulations slightly overestimated the strengthening effect in compression‐treated groups due to omission of pore damage. These findings establish a quantitative process–property framework and offer a theoretical foundation for pre‐processing design strategies to optimize the thermo‐mechanical performance and service life of lightweight honeycomb components such as UAV wings.
- 7 April 2025
- Published by Wiley in Fatigue & Fracture of Engineering Materials & Structures
- Vol. 48 (7) , 2821-2833
Fractal Analysis and Mechanical Characterization of 3D‐Printed Concave Hexagonal Structures With Negative Poisson's Ratio
Materials with a negative Poisson's ratio have gained attention for their unique mechanical properties, enabling applications in aerospace, construction, and medicine. However, the complex geometry of such structures poses challenges for traditional manufacturing. 3D printing offers a solution, allowing precise fabrication of these intricate designs. This study uses 3D printing to create three types of structures from PLA: concave hexagonal, four‐directional chiral, and biomimetic feather structures. Tensile testing revealed that the concave hexagonal structure outperformed the others in mechanical strength. Finite element simulations confirmed its superior load‐bearing capacity during fracture. Additionally, fractal analysis showed the concave hexagonal structure had the highest fractal dimension in crack propagation, further validating its mechanical superiority. These findings highlight the concave hexagonal structure's advantages through experimental, numerical, and fractal analyses.
- 7 April 2025
- Published by Wiley in Fatigue & Fracture of Engineering Materials & Structures
- Vol. 48 (7) , 2821-2833
Fractal Analysis and Mechanical Characterization of 3D‐Printed Concave Hexagonal Structures With Negative Poisson's Ratio
Materials with a negative Poisson's ratio have gained attention for their unique mechanical properties, enabling applications in aerospace, construction, and medicine. However, the complex geometry of such structures poses challenges for traditional manufacturing. 3D printing offers a solution, allowing precise fabrication of these intricate designs. This study uses 3D printing to create three types of structures from PLA: concave hexagonal, four‐directional chiral, and biomimetic feather structures. Tensile testing revealed that the concave hexagonal structure outperformed the others in mechanical strength. Finite element simulations confirmed its superior load‐bearing capacity during fracture. Additionally, fractal analysis showed the concave hexagonal structure had the highest fractal dimension in crack propagation, further validating its mechanical superiority. These findings highlight the concave hexagonal structure's advantages through experimental, numerical, and fractal analyses.
- 19 August 2024
- Published by Elsevier in Journal of the Mechanical Behavior of Biomedical Materials
- Vol. 159, 106699
Exploring anisotropic mechanical properties of lobster claw exoskeleton through fractal models
- 19 August 2024
- Published by Elsevier in Journal of the Mechanical Behavior of Biomedical Materials
- Vol. 159, 106699
Exploring anisotropic mechanical properties of lobster claw exoskeleton through fractal models