Lei Guo
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Lei Guo has a total of 26 co-authors. Here are the top co-authors by number of shared publications:
- Zhengxiao Guo
HKU‐CAS Joint Laboratory on New Materials & Department of Chemistry The University of Hong Kong Hong Kong SAR P. R. China
10 shared publications - Zhancheng Guo
State Key Laboratory of Advanced Metallurgy, University of Science and Technology Beijing, Beijing 100083, China
3 shared publications Haibin Zuo
State Key Laboratory of Advanced Metallurgy University of Science and Technology Beijing Beijing 100083 China
2 shared publications- Jintao Gao
State Key Laboratory of Advanced Metallurgy, University of Science and Technology Beijing
2 shared publications Qipeng Bao
State Key Laboratory of Advanced Metallurgy, University of Science and Technology Beijing, Beijing, China
2 shared publications- Qipeng Bao
State Key Laboratory of Advanced Metallurgy, University of Science and Technology Beijing, Xueyuan Road No.30, Haidian district, Beijing 100083, China
2 shared publications
Latest Publications
- Open Access
- 15 November 2025
- Published by Iron and Steel Institute of Japan in ISIJ International
- Vol. 65 (12) , 1850-1859
Phase Diagrams of “FeO”–SiO2–CaO–V2O3–TiO2 System and Phase Transformation of Vanadium-enriched Phases
Achieving phase transformation from spinel to the vanadium-enriched phase with higher chemical activity of vanadium oxide is essential for the efficient extraction of vanadium resources in vanadium slag. However, there is a severe lack of thermodynamic data for the relevant systems, which hampers our understanding for phase relations of vanadium-enriched phases. In this study, the phase equilibria of the "FeO"-SiO2-CaO-V2O3-TiO2 system were investigated at 1400 °C and 1200 °C, and the corresponding phase diagrams were constructed. It was found from these phase diagrams that the vanadium-rich phase (V,Ti,Fe)2O3 with a higher chemical activity of vanadium oxide than Fe(V,Ti,Fe)2O4 was identified, but the decrease in temperature was detrimental to the crystallization of (V,Ti,Fe)2O3. On these bases, the phase transformation from Fe(V,Ti,Fe)2O4 to (V,Ti,Fe)2O3 was further investigated at 1400 °C. It was found that the phase transformation occurred in three stages: the Fe(V,Ti,Fe)2O4 stage, the coexistence stage of Fe(V,Ti,Fe)2O4 and (V,Ti,Fe)2O3, and the (V,Ti,Fe)2O3 stage, and the phase transformation from Fe(V,Ti,Fe)2O4 to (V,Ti,Fe)2O3 was fully completed when the w("FeO")/w(SiO2) ratio was lower than 0.8. In this study, the essential thermodynamic data of the relevant system are complemented, while the phase transformation results of vanadium-enriched phases provide theoretical guidance for the efficient extraction of vanadium resources from vanadium slag.
- 15 November 2025
- Published by Iron and Steel Institute of Japan in ISIJ International
- Vol. 65 (12) , 1850-1859
Open AccessPhase Diagrams of “FeO”–SiO2–CaO–V2O3–TiO2 System and Phase Transformation of Vanadium-enriched Phases
Achieving phase transformation from spinel to the vanadium-enriched phase with higher chemical activity of vanadium oxide is essential for the efficient extraction of vanadium resources in vanadium slag. However, there is a severe lack of thermodynamic data for the relevant systems, which hampers our understanding for phase relations of vanadium-enriched phases. In this study, the phase equilibria of the "FeO"-SiO2-CaO-V2O3-TiO2 system were investigated at 1400 °C and 1200 °C, and the corresponding phase diagrams were constructed. It was found from these phase diagrams that the vanadium-rich phase (V,Ti,Fe)2O3 with a higher chemical activity of vanadium oxide than Fe(V,Ti,Fe)2O4 was identified, but the decrease in temperature was detrimental to the crystallization of (V,Ti,Fe)2O3. On these bases, the phase transformation from Fe(V,Ti,Fe)2O4 to (V,Ti,Fe)2O3 was further investigated at 1400 °C. It was found that the phase transformation occurred in three stages: the Fe(V,Ti,Fe)2O4 stage, the coexistence stage of Fe(V,Ti,Fe)2O4 and (V,Ti,Fe)2O3, and the (V,Ti,Fe)2O3 stage, and the phase transformation from Fe(V,Ti,Fe)2O4 to (V,Ti,Fe)2O3 was fully completed when the w("FeO")/w(SiO2) ratio was lower than 0.8. In this study, the essential thermodynamic data of the relevant system are complemented, while the phase transformation results of vanadium-enriched phases provide theoretical guidance for the efficient extraction of vanadium resources from vanadium slag.
- Open Access
- 10 October 2025
- Published by Springer Nature in International Journal of Minerals, Metallurgy and Materials
- Vol. 32 (10) , 2483-2494
Extreme removal of fine inclusions from 304 stainless steel via high-temperature supergravity fields
- 10 October 2025
- Published by Springer Nature in International Journal of Minerals, Metallurgy and Materials
- Vol. 32 (10) , 2483-2494
Open AccessExtreme removal of fine inclusions from 304 stainless steel via high-temperature supergravity fields
- 7 April 2024
- Published by Wiley in Steel Research International
- Vol. 95 (6)
Numerical Simulation of the Effect of Feeding Mode on the Reduction of Ore Powder in Hydrogen‐Based Flash Ironmaking Process
The efficiency and heat utilization of modern large‐scale blast furnace in China are close to limits. The potential for energy saving and consumption reduction by continuing to improve blast furnace operation is limited, so there is a need to develop nonblast furnace ironmaking technologies to solve the problems of high energy consumption and pollution. The emerging flash ironmaking technology, which is highly efficient and has low pollutant emissions, has become an option. This article uses CFD software to simulate the 3D steady‐state hydrogen‐based flash ironmaking process at a pilot scale. It is a complex system involving gas‐particle two‐phase flow, heat transfer, and chemical reactions. The article mainly studies the effects of the feeding mode and hydrogen concentration in the reducing gas on the reduction of ore particles. The results show that the residence time of the particles in the furnace is very sensitive to the feeding method, and the maximum residence time of the particles reaches about 2.8 s under the optimal feeding method. In addition, increasing the hydrogen concentration in the reducing gas decreases the particles’ residence time. However, the minimum residence time is more than 2.2 s, and the ore powder can still obtain a high reduction degree.
- 7 April 2024
- Published by Wiley in Steel Research International
- Vol. 95 (6)
Numerical Simulation of the Effect of Feeding Mode on the Reduction of Ore Powder in Hydrogen‐Based Flash Ironmaking Process
The efficiency and heat utilization of modern large‐scale blast furnace in China are close to limits. The potential for energy saving and consumption reduction by continuing to improve blast furnace operation is limited, so there is a need to develop nonblast furnace ironmaking technologies to solve the problems of high energy consumption and pollution. The emerging flash ironmaking technology, which is highly efficient and has low pollutant emissions, has become an option. This article uses CFD software to simulate the 3D steady‐state hydrogen‐based flash ironmaking process at a pilot scale. It is a complex system involving gas‐particle two‐phase flow, heat transfer, and chemical reactions. The article mainly studies the effects of the feeding mode and hydrogen concentration in the reducing gas on the reduction of ore particles. The results show that the residence time of the particles in the furnace is very sensitive to the feeding method, and the maximum residence time of the particles reaches about 2.8 s under the optimal feeding method. In addition, increasing the hydrogen concentration in the reducing gas decreases the particles’ residence time. However, the minimum residence time is more than 2.2 s, and the ore powder can still obtain a high reduction degree.
- Open Access
Synthesis of TiCx/Al Composites via In Situ Reaction between AlxTi Melt and Dissolvable Solid Carbon
TiCx/Al composites were successfully prepared in this study by dissolving graphite particles in Al-Ti melt based on the principle of a solid–liquid in situ reaction. It was observed that the microstructure of the TiCx/Al composites changed with changes in the reaction temperature and graphite particle size. With an increase in reaction temperature, the TiCx particles in the TiCx/Al composites transitioned from a spider-like distribution to being evenly dispersed in the Al matrix. Additionally, the morphology of the TiCx particles changed from polygons of various sizes to quasi-spherical shapes with a uniform particle size, while the presence of Al4C3 and Al3Ti in the matrix diminished. The size variation of the graphite particles had minimal impact on the particle size and stoichiometric ratio of TiCx generated in the sample. Furthermore, an appropriate graphite particle size was found to mitigate the agglomeration and residue of graphite particles during the in situ reaction.
Open AccessSynthesis of TiCx/Al Composites via In Situ Reaction between AlxTi Melt and Dissolvable Solid Carbon
TiCx/Al composites were successfully prepared in this study by dissolving graphite particles in Al-Ti melt based on the principle of a solid–liquid in situ reaction. It was observed that the microstructure of the TiCx/Al composites changed with changes in the reaction temperature and graphite particle size. With an increase in reaction temperature, the TiCx particles in the TiCx/Al composites transitioned from a spider-like distribution to being evenly dispersed in the Al matrix. Additionally, the morphology of the TiCx particles changed from polygons of various sizes to quasi-spherical shapes with a uniform particle size, while the presence of Al4C3 and Al3Ti in the matrix diminished. The size variation of the graphite particles had minimal impact on the particle size and stoichiometric ratio of TiCx generated in the sample. Furthermore, an appropriate graphite particle size was found to mitigate the agglomeration and residue of graphite particles during the in situ reaction.
- 1 March 2024
- Published by Springer Nature in International Journal of Minerals, Metallurgy and Materials
- Vol. 31 (3) , 473-484
New process for treating boron-bearing iron ore by flash reduction coupled with magnetic separation
- 1 March 2024
- Published by Springer Nature in International Journal of Minerals, Metallurgy and Materials
- Vol. 31 (3) , 473-484
New process for treating boron-bearing iron ore by flash reduction coupled with magnetic separation
- 26 December 2021
- Published by Springer Nature in International Journal of Minerals, Metallurgy and Materials
- Vol. 29 (2) , 228-238
Numerical simulation of flash reduction in a drop tube reactor with variable temperatures
- 26 December 2021
- Published by Springer Nature in International Journal of Minerals, Metallurgy and Materials
- Vol. 29 (2) , 228-238
Numerical simulation of flash reduction in a drop tube reactor with variable temperatures
- 24 November 2021
- Published by Springer Nature in International Journal of Minerals, Metallurgy and Materials
- Vol. 28 (12) , 1929-1939
Rapid removal of copper impurity from bismuth-copper alloy melts via super-gravity separation
- 24 November 2021
- Published by Springer Nature in International Journal of Minerals, Metallurgy and Materials
- Vol. 28 (12) , 1929-1939
Rapid removal of copper impurity from bismuth-copper alloy melts via super-gravity separation
- 27 October 2021
- Published by Wiley in Steel Research International
- Vol. 93 (4) , 2100407
A Computational Fluid Dynamics Simulation Method to Optimize the Structure Parameters of Coal‐Based Flash Ironmaking Reactors
The coal‐based flash ironmaking furnace is designed to industrialize the novel flash ironmaking technology (FIT), which is recognized as a cleaner and efficient alternative ironmaking process. To realize gas‐particle contact, researchers use the cocurrent downer to reduce bonding, and the reactor structure has a significant effect on the flow pattern. Herein, a 3D computational fluid dynamics (CFD) model is developed to obtain an in‐depth understanding of the geometry parameters, including ore feeding position (r/R), shaft diameter (D), and height‐to‐diameter ratio (L/D). The simulation results show that the secondary gas flow caused by the dropping hematite particles might enhance or destroy the primary turbulence structure when r/R was below or above 0.6. The increased shaft diameter D expanded the recirculation zone, which helps to prolong the residence time and improve the species exchange. The particles’ reduction degrees first rise and then fell, and the highest value (90.89%) is attained at D = 2.2 m. On the contrary, the increased L/D ratio does not change the turbulence structure but prolongs the length of the plug zone. It also shows a positive but declining effect on the reduction degree from 89.7% to 99.8%.
- 27 October 2021
- Published by Wiley in Steel Research International
- Vol. 93 (4) , 2100407
A Computational Fluid Dynamics Simulation Method to Optimize the Structure Parameters of Coal‐Based Flash Ironmaking Reactors
The coal‐based flash ironmaking furnace is designed to industrialize the novel flash ironmaking technology (FIT), which is recognized as a cleaner and efficient alternative ironmaking process. To realize gas‐particle contact, researchers use the cocurrent downer to reduce bonding, and the reactor structure has a significant effect on the flow pattern. Herein, a 3D computational fluid dynamics (CFD) model is developed to obtain an in‐depth understanding of the geometry parameters, including ore feeding position (r/R), shaft diameter (D), and height‐to‐diameter ratio (L/D). The simulation results show that the secondary gas flow caused by the dropping hematite particles might enhance or destroy the primary turbulence structure when r/R was below or above 0.6. The increased shaft diameter D expanded the recirculation zone, which helps to prolong the residence time and improve the species exchange. The particles’ reduction degrees first rise and then fell, and the highest value (90.89%) is attained at D = 2.2 m. On the contrary, the increased L/D ratio does not change the turbulence structure but prolongs the length of the plug zone. It also shows a positive but declining effect on the reduction degree from 89.7% to 99.8%.
- 28 June 2020
- Published by Springer Nature in Journal of Iron and Steel Research International
- Vol. 27 (11) , 1322-1330
Recovery of zinc from Zn–Al–Fe alloys by gas pressure filtration
- 28 June 2020
- Published by Springer Nature in Journal of Iron and Steel Research International
- Vol. 27 (11) , 1322-1330
Recovery of zinc from Zn–Al–Fe alloys by gas pressure filtration
- Open Access
Kinetic Models for the in Situ Reaction between Cu-Ti Melt and Graphite
The in situ reaction method for preparing metal matrix composites has the advantages of a simple process, good combination of the reinforcing phase and matrix, etc. Based on the mechanism of forming TiCx particles via the dissolution reaction of solid carbon (C) particles in Cu-Ti melt, the kinetic models for C particle dissolution reaction were established. The kinetic models of the dissolution reaction of spherical, cylindrical, and flat C source particles in Cu-Ti melt were deduced, and the expressions of the time for the complete reaction of C source particles of different sizes were obtained. The mathematical relationship between the degree of reaction of C source and the reaction time was deduced by introducing the shape factor. By immersing a cylindrical C rod in a Cu-Ti melt and placing it in a super-gravity field for the dissolution reaction, it was found that the super-gravity field could cause the precipitated TiCx particles to aggregate toward the upper part of the sample under the action of buoyancy. Therefore, the consuming rate of the C rod was significantly accelerated. Based on the flat C source reaction kinetic model, the relationship between the floating speed of TiCx particles in the Cu-Ti melt and the centrifugal velocity (or the coefficient of super-gravity G) was derived. It was proven that, when the centrifugal velocity exceeded a critical value, the super-gravity field could completely avoid the accumulation behavior of TiCx particles on the surface of the C source, thereby speeding up the formation reaction of TiCx. The goal of this study is to better understand and evaluate the generating process of TiCx particles, thus finding possible methods to increase the reaction efficiency
Open AccessKinetic Models for the in Situ Reaction between Cu-Ti Melt and Graphite
The in situ reaction method for preparing metal matrix composites has the advantages of a simple process, good combination of the reinforcing phase and matrix, etc. Based on the mechanism of forming TiCx particles via the dissolution reaction of solid carbon (C) particles in Cu-Ti melt, the kinetic models for C particle dissolution reaction were established. The kinetic models of the dissolution reaction of spherical, cylindrical, and flat C source particles in Cu-Ti melt were deduced, and the expressions of the time for the complete reaction of C source particles of different sizes were obtained. The mathematical relationship between the degree of reaction of C source and the reaction time was deduced by introducing the shape factor. By immersing a cylindrical C rod in a Cu-Ti melt and placing it in a super-gravity field for the dissolution reaction, it was found that the super-gravity field could cause the precipitated TiCx particles to aggregate toward the upper part of the sample under the action of buoyancy. Therefore, the consuming rate of the C rod was significantly accelerated. Based on the flat C source reaction kinetic model, the relationship between the floating speed of TiCx particles in the Cu-Ti melt and the centrifugal velocity (or the coefficient of super-gravity G) was derived. It was proven that, when the centrifugal velocity exceeded a critical value, the super-gravity field could completely avoid the accumulation behavior of TiCx particles on the surface of the C source, thereby speeding up the formation reaction of TiCx. The goal of this study is to better understand and evaluate the generating process of TiCx particles, thus finding possible methods to increase the reaction efficiency