Saravanan Ramasamy
Research Subjects
Saravanan Ramasamy has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
- Dharmaraj Rajalinggam
KPR Institute of Engineering and Technology, India
2 shared publications - Aruna Govindan
BMS Institute of Technology and Management, India
1 shared publication Dharmaraj Rajalinggam
KPR Institute of Engineering and Technology, India
1 shared publicationKaruppasamy Narayanan
Sona College of Technology, India
1 shared publication- Karuppasamy Narayanan
Department of Civil Engineering, Sona College of Technology, Salem, India
1 shared publication M. Kannan
1 shared publication
Latest Publications
- Open Access
- 1 January 2026
- Published by FapUNIFESP (SciELO) in Matéria (Rio de Janeiro)
- Vol. 31
Experimental investigation of reinforced cement concrete and nylon fiber reinforced concrete beam
Concrete is brittle substance whose tensile strength and flexural strength are low and may easily crack and its lifespan is limited. The proposed research aims at assessing how the addition of nylon fiber affects the mechanical and workability of M30 grade reinforced cement concrete (RCC). The originality of this study is that the nylon fibers used are used at optimal dosage (0.25% and 0.5% by volume) in order to improve both strength and durability without impairing the workability. Six series of specimens were cast and experimented on compressive, split tensile and flexural strength, and slump cone testing of fresh concrete workability. The findings showed that the compressive, split tensile and flexural strengths were increased by 11, 14 and 17 percent respectively by the addition of 0.5 percent nylon fiber over plain M30 concrete. The enhancement in mechanical performance is attributed to improved fiber matrix interfacial bonding and crack-bridging mechanisms provided by the dispersed nylon fibers. The fibers effectively delay crack propagation and redistribute tensile stresses within the concrete matrix. Engineering wise, the nylon fiber-reinforced concrete is a cost-effective and structural-friendly substitute of structural application in which enhanced tensile and flexural strengths are needed.
- 1 January 2026
- Published by FapUNIFESP (SciELO) in Matéria (Rio de Janeiro)
- Vol. 31
Open AccessExperimental investigation of reinforced cement concrete and nylon fiber reinforced concrete beam
Concrete is brittle substance whose tensile strength and flexural strength are low and may easily crack and its lifespan is limited. The proposed research aims at assessing how the addition of nylon fiber affects the mechanical and workability of M30 grade reinforced cement concrete (RCC). The originality of this study is that the nylon fibers used are used at optimal dosage (0.25% and 0.5% by volume) in order to improve both strength and durability without impairing the workability. Six series of specimens were cast and experimented on compressive, split tensile and flexural strength, and slump cone testing of fresh concrete workability. The findings showed that the compressive, split tensile and flexural strengths were increased by 11, 14 and 17 percent respectively by the addition of 0.5 percent nylon fiber over plain M30 concrete. The enhancement in mechanical performance is attributed to improved fiber matrix interfacial bonding and crack-bridging mechanisms provided by the dispersed nylon fibers. The fibers effectively delay crack propagation and redistribute tensile stresses within the concrete matrix. Engineering wise, the nylon fiber-reinforced concrete is a cost-effective and structural-friendly substitute of structural application in which enhanced tensile and flexural strengths are needed.
- 28 April 2025
- Published by Walter de Gruyter GmbH in Journal of Polymer Engineering
- Vol. 45 (6) , 537-547
Experimental study on the usage of biopolymer sodium alginate as drainage barrier in liners
This study investigates the impact of sodium alginate (SA) as a biopolymer on the consistency, compaction and consolidation characteristics of soil, specifically for use as a drainage barrier in soil stabilization applications. The research indicates that increasing sodium alginate concentrations in the soil raises the liquid limit (LL) by 51 % and plastic limit (PL) by 30 %, suggesting an interaction between clay particles and the admixture. To enhance the stability of SA, the optimum quantity of SA of 0.75 % was treated with calcium chloride, leading to the synthesis of calcium alginate (CA) using two methods: solvent casting process and hardening method. The study examines the role of cross-linking agents like calcium chloride in enhancing the stability of soil treated with SA for use as a drainage barrier in liner/cover systems. The hydraulic conductivity of untreated and treated soil met the US EPA requirement of 10−9 cm/s for a low-permeability soil liner. But the SCP-treated sample exhibited more stable hydraulic movement than the others. Also the compression index was increased by 0.012-fold for SCP method when compared with untreated soil, indicating changes in pore space tightness. SEM and FTIR studies were performed to evaluate the efficacy of CA at the microstructural level.
- 28 April 2025
- Published by Walter de Gruyter GmbH in Journal of Polymer Engineering
- Vol. 45 (6) , 537-547
Experimental study on the usage of biopolymer sodium alginate as drainage barrier in liners
This study investigates the impact of sodium alginate (SA) as a biopolymer on the consistency, compaction and consolidation characteristics of soil, specifically for use as a drainage barrier in soil stabilization applications. The research indicates that increasing sodium alginate concentrations in the soil raises the liquid limit (LL) by 51 % and plastic limit (PL) by 30 %, suggesting an interaction between clay particles and the admixture. To enhance the stability of SA, the optimum quantity of SA of 0.75 % was treated with calcium chloride, leading to the synthesis of calcium alginate (CA) using two methods: solvent casting process and hardening method. The study examines the role of cross-linking agents like calcium chloride in enhancing the stability of soil treated with SA for use as a drainage barrier in liner/cover systems. The hydraulic conductivity of untreated and treated soil met the US EPA requirement of 10−9 cm/s for a low-permeability soil liner. But the SCP-treated sample exhibited more stable hydraulic movement than the others. Also the compression index was increased by 0.012-fold for SCP method when compared with untreated soil, indicating changes in pore space tightness. SEM and FTIR studies were performed to evaluate the efficacy of CA at the microstructural level.
- Open Access
- 5 January 2025
- Published by Elsevier in Desalination and Water Treatment
- Vol. 321
Fluoride removal from contaminated water using natural bio-adsorbents: A numerical and experimental investigation
- 5 January 2025
- Published by Elsevier in Desalination and Water Treatment
- Vol. 321
Open AccessFluoride removal from contaminated water using natural bio-adsorbents: A numerical and experimental investigation
- Open Access
- 1 January 2025
- Published by FapUNIFESP (SciELO) in Matéria (Rio de Janeiro)
- Vol. 30, e20240720
Axial compression behavior of edge stiffened C-profile aluminium alloy: a finite element analysis
Aluminium alloys find diverse applications in building construction. Specifically, C-profiles being used as various structural elements in the building. Providing Edge stiffeners in the C-profile leads to increase the load carrying capacity. Limited research is available on compression behaviour c-profile with edge stiffeners. Hence, this article aims to study the behaviour of a Finite Element Analysis of aluminium alloy stiffened edge C profiles subjected to axial compression. Two different aluminium alloy materials, namely 6061-T6, and 6063-T5 were investigated. Finite element models were developed and results, including ultimate load, failure modes, and load vs. axial shortening curves, were verified against existing test data. A comprehensive parametric study was carried out based on the verified finite element models, involving variation in the orientation of the edge stiffener, column length, and section thickness. A total of 144 parametric results were compared with the design strengths calculated from Euro code 9.
- 1 January 2025
- Published by FapUNIFESP (SciELO) in Matéria (Rio de Janeiro)
- Vol. 30, e20240720
Open AccessAxial compression behavior of edge stiffened C-profile aluminium alloy: a finite element analysis
Aluminium alloys find diverse applications in building construction. Specifically, C-profiles being used as various structural elements in the building. Providing Edge stiffeners in the C-profile leads to increase the load carrying capacity. Limited research is available on compression behaviour c-profile with edge stiffeners. Hence, this article aims to study the behaviour of a Finite Element Analysis of aluminium alloy stiffened edge C profiles subjected to axial compression. Two different aluminium alloy materials, namely 6061-T6, and 6063-T5 were investigated. Finite element models were developed and results, including ultimate load, failure modes, and load vs. axial shortening curves, were verified against existing test data. A comprehensive parametric study was carried out based on the verified finite element models, involving variation in the orientation of the edge stiffener, column length, and section thickness. A total of 144 parametric results were compared with the design strengths calculated from Euro code 9.
- Open Access
- 1 January 2025
- Published by FapUNIFESP (SciELO) in Matéria (Rio de Janeiro)
- Vol. 30, e20240707
Eco-friendly paver blocks: repurposing plastic waste and foundry sand
This study investigates the use of waste plastic (polyethylene and polypropylene) and foundry sand to manufacture eco-friendly paver blocks, providing a sustainable alternative to conventional materials. The project aims to address the challenges of plastic waste disposal and environmental damage caused by sand mining. Twelve paver block samples were prepared with varying proportions of plastic (30%–60%) and foundry sand, with or without coarse aggregate. The mechanical properties, including compressive strength, flexural strength, water absorption, and fire resistance, were tested following ASTM standards. The optimal mix, FPA-2 (40% plastic, 40% foundry sand, 20% coarse aggregate), exhibited a compressive strength of 27 N/mm2 and a flexural strength of 6.7 N/mm2, comparable to traditional paver blocks. Water absorption rates were below 7%, and the blocks met fire resistance criteria. Cost analysis revealed that plastic-based paver blocks are up to 25% cheaper than conventional ones, enhancing their economic feasibility. By repurposing waste materials, this study offers a sustainable solution for reducing natural resource dependency and mitigating environmental harm. The findings highlight the potential for plastic-based paver blocks to promote circular economy practices, maintain performance standards, and provide cost-effective alternatives for the construction industry.
- 1 January 2025
- Published by FapUNIFESP (SciELO) in Matéria (Rio de Janeiro)
- Vol. 30, e20240707
Open AccessEco-friendly paver blocks: repurposing plastic waste and foundry sand
This study investigates the use of waste plastic (polyethylene and polypropylene) and foundry sand to manufacture eco-friendly paver blocks, providing a sustainable alternative to conventional materials. The project aims to address the challenges of plastic waste disposal and environmental damage caused by sand mining. Twelve paver block samples were prepared with varying proportions of plastic (30%–60%) and foundry sand, with or without coarse aggregate. The mechanical properties, including compressive strength, flexural strength, water absorption, and fire resistance, were tested following ASTM standards. The optimal mix, FPA-2 (40% plastic, 40% foundry sand, 20% coarse aggregate), exhibited a compressive strength of 27 N/mm2 and a flexural strength of 6.7 N/mm2, comparable to traditional paver blocks. Water absorption rates were below 7%, and the blocks met fire resistance criteria. Cost analysis revealed that plastic-based paver blocks are up to 25% cheaper than conventional ones, enhancing their economic feasibility. By repurposing waste materials, this study offers a sustainable solution for reducing natural resource dependency and mitigating environmental harm. The findings highlight the potential for plastic-based paver blocks to promote circular economy practices, maintain performance standards, and provide cost-effective alternatives for the construction industry.
- 12 April 2024
- Published by Springer Nature in Environment, Development and Sustainability
- Vol. 27 (12) , 29989-30006
Evaluation of continuous flow anaerobic suspended growth reactor for treating papaer and pulp effluent
- 12 April 2024
- Published by Springer Nature in Environment, Development and Sustainability
- Vol. 27 (12) , 29989-30006
Evaluation of continuous flow anaerobic suspended growth reactor for treating papaer and pulp effluent
- Open Access
- 1 January 2024
- Published by FapUNIFESP (SciELO) in Matéria (Rio de Janeiro)
- Vol. 29 (3) , e20240068
The influence of ZnO nanoparticles on mechanical and early-age hydration behaviour of cement paste
An ultrasonic treatment was used to ensure that the nano zinc oxide abbreviated ZnO, was uniformly dispersed throughout the cement paste mixture with addition of fly ash, replacing 10% of the weight of cement. The characteristics of the cementitious mixture were investigated in this research work. The experimental work was carried out by adding nano-ZnO in increments of 0%, 0.25%, 0.5%, 0.75% and 1% by weight of cement, resulting in changes in the characteristics of the concrete paste. The quantity of nano-ZnO present in the cementitious mixture had a notable influence on the consistency of the cement. This impact was also found when the cement paste contained only 0.5% cement by weight. The electrical resistance studies found that the inclusion of nano-sized particles can both delay the hydration of blended cement mix and increase the hydration rate. The findings of experiments revealed that increasing the nano-ZnO concentrations in the cement paste resulted in greater long-term strength. Furthermore, the pore diameter distribution was optimized by the inclusion of nano-ZnO and a tight microstructure was formed in the cementitious mixture at 28 days.
- 1 January 2024
- Published by FapUNIFESP (SciELO) in Matéria (Rio de Janeiro)
- Vol. 29 (3) , e20240068
Open AccessThe influence of ZnO nanoparticles on mechanical and early-age hydration behaviour of cement paste
An ultrasonic treatment was used to ensure that the nano zinc oxide abbreviated ZnO, was uniformly dispersed throughout the cement paste mixture with addition of fly ash, replacing 10% of the weight of cement. The characteristics of the cementitious mixture were investigated in this research work. The experimental work was carried out by adding nano-ZnO in increments of 0%, 0.25%, 0.5%, 0.75% and 1% by weight of cement, resulting in changes in the characteristics of the concrete paste. The quantity of nano-ZnO present in the cementitious mixture had a notable influence on the consistency of the cement. This impact was also found when the cement paste contained only 0.5% cement by weight. The electrical resistance studies found that the inclusion of nano-sized particles can both delay the hydration of blended cement mix and increase the hydration rate. The findings of experiments revealed that increasing the nano-ZnO concentrations in the cement paste resulted in greater long-term strength. Furthermore, the pore diameter distribution was optimized by the inclusion of nano-ZnO and a tight microstructure was formed in the cementitious mixture at 28 days.