Paul T. Mead
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Paul T. Mead has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
Charles U. Pittman
Mississippi State University
2 shared publications- Jacob A. Rogers
Texas A&M University
2 shared publications - Thomas E. Lacy
J. Mike Walker ’66 Department of Mechanical Engineering, Texas A&M University, College Station, USA
2 shared publications Aniket Mote
Texas A&M University
1 shared publicationEdwin L. Thomas
Texas A&M University
1 shared publication- Edwin Lorimer Thomas
Texas A & M Univ., College Station, TX (United States)
1 shared publication
Latest Publications
- Open Access
- 9 June 2026
- Published by Open Engineering Inc in engrXiv
Temperature Dependence of the Hypervelocity Impact Response of Polyethylene Plates from Tg to Tm
All spacecraft continue to face a growing risk of hypervelocity impact (HVI) by micrometeoroids and orbital debris (MMOD). Concurrently, emerging hypersonic weapons pose acute ballistic threats to military and civilian assets. In both cases, the diminishing effectiveness of legacy armor demands the development of specialized, layered HVI protective structures. Ultra-high molecular weight polyethylene (UHMWPE) and high-density polyethylene (HDPE) stand out as promising intermediate layers due to their high mass-specific energy absorption and tailorability. Yet, their behaviors at HVI-induced strain rates (>106 s-1) remain understudied and poorly understood, particularly near their glass transition (-116°C) and melt (130°C) temperatures. A recent HVI study revealed that, when impacted at room temperature, UHMWPE targets exhibited bulk fragmentation while similar HDPE samples showed extensive melting and visco-plastic flow, differences attributed to molecular mobility. This follow-on study probes the interplay of initial target temperature (T0), impact velocity (v0), and average entanglements per chain (Ne) on polyethylene’s (PE’s) HVI response. 12.7 mm thick UHMWPE and HDPE plates at T0 = -120°C, 20°C, and 140°C were subjected to 2.5 km/s and 6.0 km/s HVIs by 6.35 mm diameter aluminum spheres. PE’s HVI response was found to be largely governed by a competition between rates of strain and polymer chain relaxation. Lowering T0 for a fixed Ne constrained chain motion analogously to increasing Ne at a fixed T0. This caused HDPE’s HVI response to increasingly align with UHMWPE’s at similar v0. The opposite was also observed. Increasing v0 alone made both materials more prone to widespread fracture by raising strain rates beyond rates of chain disentanglement and reorientation. The material exhibiting the most visco-plastic flow without subsequent bulk fragmentation lost less mass, had smaller perforations, and better absorbed energy, suggesting that, for a given T0 and v0, there is an optimal Ne value that maximizes PE energy absorption. Increasing v0 or decreasing T0 necessitates a reduction in Ne to sustain the degree of molecular mobility that gives maximum energy absorption. These findings motivate the development of a protective structure composed of PE layers, each optimized for an anticipated average strain rate.
- 9 June 2026
- Published by Open Engineering Inc in engrXiv
Open AccessTemperature Dependence of the Hypervelocity Impact Response of Polyethylene Plates from Tg to Tm
All spacecraft continue to face a growing risk of hypervelocity impact (HVI) by micrometeoroids and orbital debris (MMOD). Concurrently, emerging hypersonic weapons pose acute ballistic threats to military and civilian assets. In both cases, the diminishing effectiveness of legacy armor demands the development of specialized, layered HVI protective structures. Ultra-high molecular weight polyethylene (UHMWPE) and high-density polyethylene (HDPE) stand out as promising intermediate layers due to their high mass-specific energy absorption and tailorability. Yet, their behaviors at HVI-induced strain rates (>106 s-1) remain understudied and poorly understood, particularly near their glass transition (-116°C) and melt (130°C) temperatures. A recent HVI study revealed that, when impacted at room temperature, UHMWPE targets exhibited bulk fragmentation while similar HDPE samples showed extensive melting and visco-plastic flow, differences attributed to molecular mobility. This follow-on study probes the interplay of initial target temperature (T0), impact velocity (v0), and average entanglements per chain (Ne) on polyethylene’s (PE’s) HVI response. 12.7 mm thick UHMWPE and HDPE plates at T0 = -120°C, 20°C, and 140°C were subjected to 2.5 km/s and 6.0 km/s HVIs by 6.35 mm diameter aluminum spheres. PE’s HVI response was found to be largely governed by a competition between rates of strain and polymer chain relaxation. Lowering T0 for a fixed Ne constrained chain motion analogously to increasing Ne at a fixed T0. This caused HDPE’s HVI response to increasingly align with UHMWPE’s at similar v0. The opposite was also observed. Increasing v0 alone made both materials more prone to widespread fracture by raising strain rates beyond rates of chain disentanglement and reorientation. The material exhibiting the most visco-plastic flow without subsequent bulk fragmentation lost less mass, had smaller perforations, and better absorbed energy, suggesting that, for a given T0 and v0, there is an optimal Ne value that maximizes PE energy absorption. Increasing v0 or decreasing T0 necessitates a reduction in Ne to sustain the degree of molecular mobility that gives maximum energy absorption. These findings motivate the development of a protective structure composed of PE layers, each optimized for an anticipated average strain rate.
- 15 August 2025
- Published by Springer Nature in Journal of Dynamic Behavior of Materials
- Vol. 12 (2) , 126-142
EPIC Simulations of Hypervelocity Impacts of Aluminum Spheres into High-Density Polyethylene Plates
- 15 August 2025
- Published by Springer Nature in Journal of Dynamic Behavior of Materials
- Vol. 12 (2) , 126-142
EPIC Simulations of Hypervelocity Impacts of Aluminum Spheres into High-Density Polyethylene Plates
- 31 July 2025
- Published by Elsevier in International Journal of Impact Engineering
- Vol. 207
Size matters: Impact energy absorption across five decades of length scale
- 31 July 2025
- Published by Elsevier in International Journal of Impact Engineering
- Vol. 207
Size matters: Impact energy absorption across five decades of length scale
- 30 October 2024
- Published by Elsevier in International Journal of Impact Engineering
- Vol. 196
Design and evaluation of additively manufactured polyetherimide orbital debris shielding for spacecraft
- 30 October 2024
- Published by Elsevier in International Journal of Impact Engineering
- Vol. 196
Design and evaluation of additively manufactured polyetherimide orbital debris shielding for spacecraft