NGNikita A. Golubkov

Nikita A. Golubkov

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Nikita A. Golubkov has a total of 16 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Mechanical justification of a new method of reconstruction of the posterolateral tibial plateau

    by Ramil S. Yagfarov, Igor A. Voronkevich, Oleg G. Zotov, Nikita A. Golubkov, Dmitry V. Stafeev, Alexandr I. Avdeev

    Introduction. Incorrect restoration of the articular surface of the tibial plateau and the limb axis leads to disruption of joint relationships and angular deformities in 19–26% of cases. Currently, numerous treatment options exist for deformities and impression fractures of the posterolateral tibial condyle (PLF), but there is no consensus on the optimal surgical strategy for treating the posterolateral tibial condyle. Objective: to evaluate and compare our proposed technique with two modern fixation methods in a mechanical test on plastic models: a lateral condylar plate and a volar palmar plate for distal radius metaphysis. Materials and Methods.The mechanical experiment was conducted at the Peter the Great St. Petersburg Polytechnical University using a Zwick/Roell Z100 universal testing machine. Uniaxial static compression of the posterolateral condyle of a plastic tibial model was performed after corrective osteotomy with simulated bone grafting and fixation using three methods, until a PLF deformation of 5 mm or damage (destruction) of the structure was achieved. Descriptive and comparative statistical methods were applied to the data obtained. Results. The mechanical study revealed that the original method yielded the highest strength values, with an average value of 1562 N (max — 1812 N; min — 1406 N) at an average deformation of 10.16 mm. This was comparable to the previous method. The volar plate yielded an average strength of 1182 N (max — 1285 N; min — 1091 N) at an average deformation of 10.56 mm, while the lateral condylar plate yielded slightly lower average values, at 1155 N (max — 1366 N; min — 893 N) at an average deformation of 9.12 mm. Conclusion.A mechanical study showed that the axial stiffness of the original tibial plateau fracture treatment, without the use of traditional plates, was comparable to that of volar plate fixation for the radius and superior to that of a lateral condylar plate.


  • Investigation of the Recovery Process During Continuous Annealing of Cold-Rolled Automotive Steels

    by P. S. Zhitelev, R. R. Adigamov, P. A. Glukhov, S. F. Sokolov, N. A. Golubkov


  • Open Access

    Mechanical properties of the VZh159–CuCr1Zr alloy multi-material samples manufactured by selective laser melting

    by A. V. Repnin, E. V. Borisov, A. A. Popovich, N. A. Golubkov

    Selective laser melting (SLM) proves to be a suitable method for fabricating multi-material products, offering heightened performance. The objective of this study is to examine the mechanical properties of the VZh159–CuCr1Zr multi-material system produced through selective laser melting. We conducted tensile and compressive strength tests on these samples, followed by fractography, examination of polished sections, and a comparison of measured mechanical properties with existing data. Our findings are summarized as follows: the phase compositions in the regions of pure alloy denote solid solutions. X-ray diffraction (XRD) patterns of the interface zone reveal peaks corresponding to both alloys. The tensile strength of VZh159–CuCr1Zr multi-material samples, as measured in tensile tests, is σu = 430 ± 20 MPa, with a relative elongation of ε = 4.6 ± 0.3 %. Results from compressive strength tests show values of σu = 822 ± 23 MPa, and relative compression ε = 42.5 ± 1.5 %. Comparing these values with those of the pure CuCr1Zr alloy, the ultimate tensile strength is approximately 53 % higher (according to available data), while the conditional yield strength is about 80 % higher. Fractography of the VZh159–CuCr1Zr multi-material sample after tensile tests indicates that the interface zone exhibits both more ductile fracture features characteristic of the CuCr1Zr alloy (pits and a lack of a smooth surface) and less ductile features charac­teristic of the VZh159 alloy (microcracks). Examination of the polished section of a VZh159–CuCr1Zr multi-material sample after compressive strength tests reveals that the presence of a more ductile CuCr1Zr alloy in the interface zone contributes to arresting the crack, which propagates at a 45° angle to the direction of load application in the VZh159 alloy region.


  • Open Access

    TiNi Alloy Lattice Structures with Negative Poisson’s Ratio: Computer Simulation and Experimental Results

    by Eduard Farber, Alexey Orlov, Evgenii Borisov, Arseniy Repnin, Stepan Kuzin, Nikita Golubkov, Anatoly Popovich

    One of the issues that modern implants face is their high stiffness, coupled with a positive Poisson’s ratio along the implant. This creates certain problems with bone inflammation and implant detachment. A possible solution to these problems is TiNi alloy lattice structure implants with low stiffness and negative Poisson’s ratio. This paper presents the results of simulation, fabrication by the SLM technique, and study of lattice structures with negative Poisson’s ratio, which can help to solve said problems. The studies involve the determination of mechanical characteristics, Poisson’s ratio, transformation temperatures, and the potential for a superelasticity effect of the lattice structure. The characteristics obtained at initial simulation were partially confirmed in the course of the works. Moreover, the possibility of fabricating TiNi alloy lattice structures with negative Poisson’s ratio (about −0.00323) and low Young’s modulus values (0.818 GPa) was confirmed by the SLM technique.