Romain Laviéville
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Romain Laviéville has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
Adeline Grenier
Universite Grenoble Alpes, CEA LETI, Grenoble, France
1 shared publication- Blend Mohamad
Univ. Grenoble Alpes, CEA, LETI, F-38000 Grenoble, France
1 shared publication C. Masante
CEA, LETI, University Grenoble-Alpes, Grenoble, France
1 shared publication- Camille Leurquin
CEA, LETI, University Grenoble-Alpes, Grenoble, France
1 shared publication Carl Jung
Universite Grenoble Alpes, CEA LETI, Grenoble, France
1 shared publicationCédric Masante
Universite Grenoble Alpes, CEA LETI, Grenoble, France
1 shared publication
Latest Publications
- Open Access
- 25 March 2025
- Published by IOP Publishing in Physica Scripta
- Vol. 100 (4) , 045952
Ni/4H-SiC ohmic contact formation using UV nanosecond laser annealing
Today, global electrification requires new materials for power applications. 4H-SiC dominates the market due to its excellent energy efficiency and wide operating range. This study explores the formation of Ni/4H-SiC backside ohmic contacts using 308 nm nanosecond laser annealing (NLA). After depositing an 80 nm layer of Ni onto 4H-SiC wafers through sputtering, different laser annealing parameters were tested. The energy densities (ED) ranged from 2.4 to 5.4 J cm −2 , the number of laser pulses applied varied from 1 to 20, and the chuck temperatures from 25 to 400 °C. For all series, a common scenario was observed as a function of ED, with initial solid state reactions, then local melting, and finally complete melting and dewetting of the top layer at high ED. An in-depth understanding of the effect of laser conditions on these stages is proposed based on electrical data, Raman spectroscopy, optical microscopy, scanning electron microscopy and transmission electron microscopy cross analysis. Increasing the pulse number and using a heated chuck can substantially lower the energy density (ED) necessary to achieve low-resistance contacts. In addition, trends in sheet resistivity and contact resistivity are related to microstructural evolution during NLA exposure. A contact resistivity of around 5 × 10 −5 Ω.cm 2 is obtained when the wafer is processed at 25 °C. It drops to 10 −5 Ω.cm 2 when processed at 400 °C.
- 25 March 2025
- Published by IOP Publishing in Physica Scripta
- Vol. 100 (4) , 045952
Open AccessNi/4H-SiC ohmic contact formation using UV nanosecond laser annealing
Today, global electrification requires new materials for power applications. 4H-SiC dominates the market due to its excellent energy efficiency and wide operating range. This study explores the formation of Ni/4H-SiC backside ohmic contacts using 308 nm nanosecond laser annealing (NLA). After depositing an 80 nm layer of Ni onto 4H-SiC wafers through sputtering, different laser annealing parameters were tested. The energy densities (ED) ranged from 2.4 to 5.4 J cm −2 , the number of laser pulses applied varied from 1 to 20, and the chuck temperatures from 25 to 400 °C. For all series, a common scenario was observed as a function of ED, with initial solid state reactions, then local melting, and finally complete melting and dewetting of the top layer at high ED. An in-depth understanding of the effect of laser conditions on these stages is proposed based on electrical data, Raman spectroscopy, optical microscopy, scanning electron microscopy and transmission electron microscopy cross analysis. Increasing the pulse number and using a heated chuck can substantially lower the energy density (ED) necessary to achieve low-resistance contacts. In addition, trends in sheet resistivity and contact resistivity are related to microstructural evolution during NLA exposure. A contact resistivity of around 5 × 10 −5 Ω.cm 2 is obtained when the wafer is processed at 25 °C. It drops to 10 −5 Ω.cm 2 when processed at 400 °C.
- 19 April 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 71 (5) , 3123-3129
Toward the Understanding on Threshold Voltage Drift Mechanisms in GaN MOSc-HEMTs Through the Influence of Device Architecture
In this article, the impact of device architecture on threshold voltage VTH instabilities during OFF state operation under a high drain voltage stress on GaN-on-Si MOSc HEMTs is thoroughly investigated. Measurement-stress–measurement high-voltage bias temperature instability (HVBTI) technique using ultrafast VGS ramp was used in this study. This measurement technique was carried out on various gate length ( ${L}_{G}$ ), ohmic length (LOHM), and field plate (FP) length. HVBTI transients performed at different ${L}_{G}$ highlight that increasing the gate length induces a better electrostatic control under the gate via a gate shielding. TCAD simulations support the claim that the relaxation peak is linked to the charge redistribution of ionized ${C}_{N}$ (-) traps under the gate. This charge redistribution during the relaxation phase is enhanced using a larger ohmic contact area. The electric field at gate and source FP corners has a strong impact on ionized ${C}_{N}$ acceptor traps located in the GaN:C layer close to the gate and consequently on positive VTH degradation observed for short stress duration. Substrate biasing and TCAD simulations suggest that the ${C}_{N}$ traps’ deionization and trapping in the volume of the gate oxide is related to the presence of free holes in the GaN:C layer.
- 19 April 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 71 (5) , 3123-3129
Toward the Understanding on Threshold Voltage Drift Mechanisms in GaN MOSc-HEMTs Through the Influence of Device Architecture
In this article, the impact of device architecture on threshold voltage VTH instabilities during OFF state operation under a high drain voltage stress on GaN-on-Si MOSc HEMTs is thoroughly investigated. Measurement-stress–measurement high-voltage bias temperature instability (HVBTI) technique using ultrafast VGS ramp was used in this study. This measurement technique was carried out on various gate length ( ${L}_{G}$ ), ohmic length (LOHM), and field plate (FP) length. HVBTI transients performed at different ${L}_{G}$ highlight that increasing the gate length induces a better electrostatic control under the gate via a gate shielding. TCAD simulations support the claim that the relaxation peak is linked to the charge redistribution of ionized ${C}_{N}$ (-) traps under the gate. This charge redistribution during the relaxation phase is enhanced using a larger ohmic contact area. The electric field at gate and source FP corners has a strong impact on ionized ${C}_{N}$ acceptor traps located in the GaN:C layer close to the gate and consequently on positive VTH degradation observed for short stress duration. Substrate biasing and TCAD simulations suggest that the ${C}_{N}$ traps’ deionization and trapping in the volume of the gate oxide is related to the presence of free holes in the GaN:C layer.