Amin Hashemi-Zadeh
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Amin Hashemi-Zadeh has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Stephan M. Goetz
University of Cambridge
4 shared publications - Nima Tashakor
Department of Electrical and Computer Engineering, Duke University, Durham, NC, USA
3 shared publications - Mahdi Bayati
Department of Electrical and Computer Engineering, Duke University, Durham, NC, USA
2 shared publications - Pouyan Pourhadi Abkenar
Department of Electrical and Computer Engineering, Rheinland-Pflzische Technische Universitt Kaiserslautern-Landau (RPTU), Kaiserslautern, Germany
2 shared publications - Ehsan Asadi
School of Electrical and Computer Engineering, College of Engineering, University of Tehran, Tehran, Iran
1 shared publication - Hans Dieter Schotten
German Research Center for Artificial Intelligence (DFKI), Kaiserslautern, Germany
1 shared publication
Latest Publications
- 1 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 13 (6) , 7364-7376
Integrated Charging Solution for Dynamically Reconfigurable Batteries for Grid Support With Power Factor Control and Virtual Inertia
- 1 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 13 (6) , 7364-7376
Integrated Charging Solution for Dynamically Reconfigurable Batteries for Grid Support With Power Factor Control and Virtual Inertia
- 20 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 13 (6) , 7455-7468
A Modular Battery System for Integrated AC, DC, and Auxiliary Outputs in Electric Vehicles
Conventional electric-vehicle battery systems are designed primarily to feed traction inverters and typically require separate converters for auxiliary loads, increasing hardware complexity, cost, and volume. This paper introduces a modular series–parallel reconfigurable battery that simultaneously delivers a main high-voltage AC or DC port as well as isolated low-voltage DC auxiliaries using the same hardware stack. Each auxiliary output requires only a single transformer and diode, while a phase-shifted carrier modulation scheme time-decouples the power paths, enabling independent regulation of the main and auxiliary ports without relays or extra conversion stages. The main port operates bidirectionally, supporting both traction and single-phase grid charging through a minimal LC filter and phase-shifted PWM. A small-signal model of the auxiliary loop provides analytical PI tuning rules to ensure stability and fast transient response. Experimental validation with a three-module prototype confirms 95% efficiency, <5% ripple in voltage and current, and ~10 ms settling time for the auxiliary port. Compared with representative onboard charger architectures, the proposed design achieves reduced part count, sensing, and control complexity while maintaining full modularity, scalability, and native multiport capability.
- 20 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 13 (6) , 7455-7468
A Modular Battery System for Integrated AC, DC, and Auxiliary Outputs in Electric Vehicles
Conventional electric-vehicle battery systems are designed primarily to feed traction inverters and typically require separate converters for auxiliary loads, increasing hardware complexity, cost, and volume. This paper introduces a modular series–parallel reconfigurable battery that simultaneously delivers a main high-voltage AC or DC port as well as isolated low-voltage DC auxiliaries using the same hardware stack. Each auxiliary output requires only a single transformer and diode, while a phase-shifted carrier modulation scheme time-decouples the power paths, enabling independent regulation of the main and auxiliary ports without relays or extra conversion stages. The main port operates bidirectionally, supporting both traction and single-phase grid charging through a minimal LC filter and phase-shifted PWM. A small-signal model of the auxiliary loop provides analytical PI tuning rules to ensure stability and fast transient response. Experimental validation with a three-module prototype confirms 95% efficiency, <5% ripple in voltage and current, and ~10 ms settling time for the auxiliary port. Compared with representative onboard charger architectures, the proposed design achieves reduced part count, sensing, and control complexity while maintaining full modularity, scalability, and native multiport capability.
- 5 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 13 (6) , 6890-6898
Cyber-Secured Modular Multilevel Converters Against False-Data Injection Attacks Through Concurrent Estimators
Over the past two decades, modular multilevel converters (MMCs) and similar cascaded circuits have become a key technology in the electricity grid, primarily for medium- and high-voltage applications. They perform important functions for grid stability as they convert, transport, and inject large power levels, connect wind farms, or compensate for power quality issues, and may in the future also contribute to grid forming. However, their complex control and monitoring subsystems as well as the sensitive nature of electronics turns them into a target for sabotage. This study investigates the operation of MMCs under various false data injection attacks (FDIA), e.g., in the power supply of data centers. The proposed solution uses two concurrent estimators, a module-level Kalman filter and an arm-level neural network estimator, to detect and mitigate complicated cyber-attacks. The proposed technique would significantly improve the resilience of MMCs against complex FDIAs and thus the resilience of critical power supplies, e.g., of DC lines and data centers. The simulations and experimental results demonstrate that the proposed detection technique outperforms state-of-the-art methods when facing sophisticated attacks and still avoids their often significant computational demands or complexity.
- 5 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 13 (6) , 6890-6898
Cyber-Secured Modular Multilevel Converters Against False-Data Injection Attacks Through Concurrent Estimators
Over the past two decades, modular multilevel converters (MMCs) and similar cascaded circuits have become a key technology in the electricity grid, primarily for medium- and high-voltage applications. They perform important functions for grid stability as they convert, transport, and inject large power levels, connect wind farms, or compensate for power quality issues, and may in the future also contribute to grid forming. However, their complex control and monitoring subsystems as well as the sensitive nature of electronics turns them into a target for sabotage. This study investigates the operation of MMCs under various false data injection attacks (FDIA), e.g., in the power supply of data centers. The proposed solution uses two concurrent estimators, a module-level Kalman filter and an arm-level neural network estimator, to detect and mitigate complicated cyber-attacks. The proposed technique would significantly improve the resilience of MMCs against complex FDIAs and thus the resilience of critical power supplies, e.g., of DC lines and data centers. The simulations and experimental results demonstrate that the proposed detection technique outperforms state-of-the-art methods when facing sophisticated attacks and still avoids their often significant computational demands or complexity.
- 19 November 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 40 (4) , 5279-5291
Asymmetrical Cascaded-Bridge Converter With Equal Modules and Sensorless Voltage Balancing for High-Quality Output
The cascading of power modules can generate multilevel voltage output to enhance power transmission capacity and quality. However, conventional cascaded converters require an excessively large number of modules for high quality and precision due to the only linear increase of the voltage levels with the number of modules. Modules whose voltages follow a decreasing sequence, e.g., a binary geometric progression (1, ½, ¼,…) imitate analog-to-digital conversion and generate very fine output shapes through a linear combination of modules with finer and finer steps. However, the use of modules with decreasing voltages rapidly reduces the energy content per module and typically requires dedicated module designs for each module voltage level. This article proposes a novel asymmetric converter design with a very different sequence of module voltages, an optimal low-cost control scheme, and accurate sensorless module-voltage regulation. The circuit does not operate any module below half of the highest-voltage module. Compared to previously suggested asymmetric cascaded circuits, modules will have significantly closer voltages. The proposed tighter rated voltage range allows for a uniform module design with fully interchangeable modules. Moreover, we introduce a pseudo-parallel mode for efficient module-to-module energy exchange. The reduced voltage difference between neighboring modules exponentially reduces the total size and dimensions of the inductors required to limit the balancing current. Simulations in MATLAB/Simulink and a hardware prototype confirm the effectiveness of this approach.
- 19 November 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 40 (4) , 5279-5291
Asymmetrical Cascaded-Bridge Converter With Equal Modules and Sensorless Voltage Balancing for High-Quality Output
The cascading of power modules can generate multilevel voltage output to enhance power transmission capacity and quality. However, conventional cascaded converters require an excessively large number of modules for high quality and precision due to the only linear increase of the voltage levels with the number of modules. Modules whose voltages follow a decreasing sequence, e.g., a binary geometric progression (1, ½, ¼,…) imitate analog-to-digital conversion and generate very fine output shapes through a linear combination of modules with finer and finer steps. However, the use of modules with decreasing voltages rapidly reduces the energy content per module and typically requires dedicated module designs for each module voltage level. This article proposes a novel asymmetric converter design with a very different sequence of module voltages, an optimal low-cost control scheme, and accurate sensorless module-voltage regulation. The circuit does not operate any module below half of the highest-voltage module. Compared to previously suggested asymmetric cascaded circuits, modules will have significantly closer voltages. The proposed tighter rated voltage range allows for a uniform module design with fully interchangeable modules. Moreover, we introduce a pseudo-parallel mode for efficient module-to-module energy exchange. The reduced voltage difference between neighboring modules exponentially reduces the total size and dimensions of the inductors required to limit the balancing current. Simulations in MATLAB/Simulink and a hardware prototype confirm the effectiveness of this approach.
- 14 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 39 (6) , 7130-7143
An Enhanced Model Predictive Capacitor Voltage Control of Hybrid Modular Multilevel Converters Under Overmodulation Circumstances
Modular multilevel converters (MMCs) require well-balanced submodule (SM) capacitor voltages at the reference value for satisfactory steady-state and dynamic operations. Achieving this goal in hybrid MMCs, where the modulation index exceeds one, becomes intricate owing to the differing participation of half-bridge submodules (HB-SMs) and full-bridge submodules (FB-SMs) in arm voltage generation. This article proposes an advanced voltage-balancing method based on enhanced phase-shift modulation and model predictive control, featuring a single comprehensive cost function that utilizes a novel form of redundancy to manage the insertion of HB- and FB-SMs in a wide range of modulation indices. The designed cost function addresses four key control objectives: intercell balancing by tracking the dc voltage reference, minimizing the energy deviation between the HB- and FB-SMs, interleg balancing to eliminate energy variations between the upper and lower arms, and rejecting voltage errors arising from uncertainties in the SM capacitance using a Kalman filter based observer. This method enables comprehensive capacitor voltage balancing, which is suitable for various modulation indices and power factors. The validity of the proposed method is substantiated through simulations using MATLAB/Simulink software and experiments conducted on a scaled-down hardware prototype.
- 14 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 39 (6) , 7130-7143
An Enhanced Model Predictive Capacitor Voltage Control of Hybrid Modular Multilevel Converters Under Overmodulation Circumstances
Modular multilevel converters (MMCs) require well-balanced submodule (SM) capacitor voltages at the reference value for satisfactory steady-state and dynamic operations. Achieving this goal in hybrid MMCs, where the modulation index exceeds one, becomes intricate owing to the differing participation of half-bridge submodules (HB-SMs) and full-bridge submodules (FB-SMs) in arm voltage generation. This article proposes an advanced voltage-balancing method based on enhanced phase-shift modulation and model predictive control, featuring a single comprehensive cost function that utilizes a novel form of redundancy to manage the insertion of HB- and FB-SMs in a wide range of modulation indices. The designed cost function addresses four key control objectives: intercell balancing by tracking the dc voltage reference, minimizing the energy deviation between the HB- and FB-SMs, interleg balancing to eliminate energy variations between the upper and lower arms, and rejecting voltage errors arising from uncertainties in the SM capacitance using a Kalman filter based observer. This method enables comprehensive capacitor voltage balancing, which is suitable for various modulation indices and power factors. The validity of the proposed method is substantiated through simulations using MATLAB/Simulink software and experiments conducted on a scaled-down hardware prototype.