Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Elayaraja Radhakrishnan has a total of 63 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Development and characterization of an epoxy-based hybrid polymer composite modified with cashew nut shell liquid, castor oil, and aluminium nanoparticles

    by Mohana Priya Ganesan, Udhayakumar Murugan, Elayaraja Radhakrishnan, Balakrishnan Krishnan, Madhanraj Varatharajan

    While conventional epoxy resins exhibit excellent mechanical properties, their inherent brittleness, lack of sustainable content, and moderate thermal performance limit their application in eco-friendly lightweight engineering. To address these limitations, this study aims to develop a sustainable hybrid polymer matrix based on epoxy matrix with the addition of 2.5 wt.% aluminium nanoparticles and additives of bio-based materials, Cashew Nut Shell Liquid (CNSL) and castor oil. Different formulations were developed and tested for mechanical, thermal and flammability properties. The tensile strength of the nano-reinforced ternary hybrid composite was the highest (51.3 MPa) while Young’s Modulus was the highest (3280 MPa) in comparison with neat epoxy (38.05 MPa and 537 MPa respectively). The flexural strength of the system reinforced with aluminium reached a maximum value of 18.11 MPa and for the ternary blend with nano-fillers it was 1.59 GPa. The impact resistance was enhanced from 1.8 J/cm 2 for neat epoxy to 2.1 J/cm 2 (neat epoxy/castor oil). The Shore-D hardness of the neat epoxy was similar, at 80, while the reinforced castor-oil epoxy measured 79. Fourier Transform InfraRed (FTIR) spectroscopy validated the good chemical interaction and crosslinking between epoxy, bio-oils and aluminium nanoparticles. Thermogravimetric analysis also showed high thermal stability as temperature of decomposition reached 369°C and char yield of 46%. Limiting Oxygen Index (LOI) was between 19 and 24 for the formulations. The outcomes showed that bio-derived oils and aluminium nanoparticles, when synergistically incorporated into the epoxy-based composites, improved the mechanical properties, thermal resistance and structural integrity of the composites.


  • Next-Generation Natural Fiber-Reinforced Materials

    by G. Ashwin Prabhu, D. Tharani, R. Sanjeevi, R. Elayaraja, S. Berlin

    Next-generation natural fiber-reinforced materials are emerging as a transformative solution for sustainable engineering applications by combining environmental compatibility with enhanced mechanical performance. This chapter per the authors examines recent innovations in natural fibers, including hybridization strategies, surface treatments, and bio-based matrices, to improve strength, durability, and moisture resistance. Advanced processing techniques such as compression molding, resin transfer molding, and additive manufacturing are analyzed for their role in optimizing material properties and manufacturing efficiency. Furthermore, the chapter highlights performance evaluation methods, lifecycle assessment, and application potential across automotive, construction, and aerospace sectors. Key challenges, including fiber variability, interfacial bonding, and large-scale commercialization, are critically discussed alongside future research directions for achieving high-performance, eco-friendly composite materials.

  • Architectural Hybridization of Natural Fibers With SS304 Wire Mesh for Superior Interlaminar Integrity

    by R. Elayaraja, G. Rajamurugan

    Delamination is a critical failure mode in laminated polymer composites, where interlaminar crack growth under out of plane loading causes rapid stiffness and strength loss. This study investigates flax fiber hybrid laminates reinforced with SS304 stainless steel wire mesh to enhance interlaminar performance, with and without a novel weaving architecture. Two laminates were fabricated by hand lay‐up: a nonwoven hybrid laminate (F0) and a woven hybrid laminate (F2), in which flax and hemp yarns were interlaced through mesh openings to create a mechanically anchored interphase. Fibers were alkali‐treated with 5% NaOH to improve fiber‐matrix adhesion. Interlaminar shear strength (ILSS) was measured using short‐beam shear tests, and Mode‐I fracture toughness was determined by double cantilever beam (DCB) testing. The woven laminate (F2) showed higher ILSS (11.02 MPa) than F0 (7.39 MPa), indicating better interfacial bonding and through‐thickness load transfer. Mode‐I fracture toughness also improved from 583 J/m 2 (F0) to 838 J/m 2 (F2), a 30% increase, demonstrating greater resistance to delamination. Fractography revealed matrix cracking and fiber pullout in F0, while F2 exhibited crack deflection, yarn bridging, and higher frictional energy dissipation. Weaving‐assisted metal‐natural fiber hybridization effectively enhances delamination resistance and shear performance in sustainable composite laminates.


  • Effect of thermal treatment on the mechanical behaviour of 3D-Printed carbon fiber-reinforced PLA bioplastic

    by Suresh S, Velmurugan D, Balaji J, Gopal P M, Elayaraja R, Sudhagar S

    This study investigates the combined influence of optimized fused deposition modeling (FDM) parameters and post-processing annealing on the mechanical, thermal, and dimensional performance of carbon fiber-reinforced polylactic acid (CF-PLA). Tensile, compressive, and flexural specimens were fabricated using FDM and subsequently annealed at 80°C, 100°C, and 120°C for holding times of 30, 60, and 90 min. Mechanical testing revealed that annealing significantly enhanced material performance when appropriate conditions were applied. The maximum tensile strength of 90.6 MPa was achieved at 80°C for 90 min, representing a 34 % improvement over untreated CF-PLA (67.43 MPa). The highest compressive strength of 90.9 MPa was obtained at 120°C for 60 min, corresponding to a 48 % improvement over untreated CF-PLA. Flexural strength reached a maximum value of 66.8 MPa, showing an improvement of about 25 % compared to untreated CF-PLA. Field Emission Scanning Electron Microscopy (FESEM) analysis confirmed enhanced interlayer adhesion, reduced porosity, and improved fiber–matrix bonding in optimally annealed samples. However, excessive annealing temperature or prolonged holding time led to polymer softening and reduced mechanical performance. The results demonstrate that controlled annealing is an effective post-processing strategy to significantly improve the mechanical reliability and structural integrity of FDM-printed CF-PLA components for load-bearing applications.


  • Sustainable Recycling of EDM Wire Waste on Nylon Mesh in Carbon Fiber Composites for a Circular Economy

    by G. Rajamurugan, R. Elayaraja, Prabu Krishnasamy, Gurtej Singh Sur, Amod Paba

  • Weaving Architecture‐Driven Changes in Mechanical, Vibration and Acoustic Behaviour of Metal Mesh Embedded Natural Fiber Hybrid Composite

    by R. Elayaraja, G. Rajamurugan

    This research aims to develop an innovative fiber‐reinforced polymer composite that integrates the advantages of flax fibers using a unique flax yarn‐weaving technique on a stainless‐steel 304 wire mesh (FSS 304). Although flax fibers offer advantageous reinforcement characteristics, their intrinsic mechanical constraints have prompted the investigation of hybrid composite designs with enhanced performance. This paper describes the fabrication and characterization of a novel hybrid composite that uses the synergistic reimbursement of FSS 304 and flax fibers, yielding a lightweight yet durable material appropriate for diverse engineering applications. Four distinct configurations (F30°, F45°, F60°, and F90°) were fabricated to examine the effects of the reinforcement orientation. The experimental findings indicate that the integration of FSS 304 markedly improves the composite hardness (F90°‐23.8 VHN), impact resistance (F30°—8.4 J), flexural strength (F90°—106.58 MPa), and tensile strength (F90°—49.2 MPa). Furthermore, acoustic analysis demonstrated that the fiber orientation substantially influences sound absorption and transmission loss, with the F90° orientation exhibiting the most effective noise reduction, especially in the 600–2000 Hz frequency range. The composite F45°‐oriented FSS 304 enhanced the natural frequency by 22%. Microstructural analysis by SEM and EDX confirmed the elemental composition. The resulting lightweight and eco‐friendly composites exhibit enhanced performance for diverse engineering applications.


  • Open Access

    Wear and erosion performance of metal mesh-reinforced natural fiber hybrid composites—a critical review

    by Elayaraja R, Rajamurugan G

    Composites made of natural fibers and polymers are a new, environmentally friendly option for many industrial and construction processes, including those in the transportation, aerospace, marine, and civil engineering industries. They are attractive options for lightweight structural components due to their intrinsic qualities, which include low density, biodegradability, and cost-effectiveness. The development of micro-cracks, moisture sensitivity, and weak fiber-matrix adhesion limit their practical use in situations prone to wear and erosion because these factors decrease their durability and reliability. Mesh reinforcements made of metals like stainless steel, copper, or aluminum are becoming more popular as a solution to these problems. Mechanical and tribological properties are improved when metallic meshes are embedded in the composite matrix. This occurs because the meshes improve interfacial bonding, promote uniform stress transfer, and effectively control fracture propagation. Adding nanoscale reinforcements, which have self-lubricating and crack-arresting properties, can further improve the material by creating synergistic strengthening at different sizes. Important design aspects, including as the mesh arrangement, fiber orientation, stacking sequence, and hierarchical interaction amongst reinforcements, determine the extent to which performance is improved. Recent advances in the study of fiber-metal mesh hybrid composites’ tribological and erosional behavior are examined in this review, which aims to shed light on the main processes involved, including fiber pull-out, matrix cracking, crack bridging, and load transfer over metallic networks. The study also details future directions involving hybrid multi-scale designs, engineered fiber-mesh interfaces, and predictive modeling strategies to achieve superior and long-lasting tribological performance, and it highlights their potential applications in high-performance sectors like braking systems, marine components, protective coatings, and structural reinforcements.


  • Improving Composite Joints with Nanoparticles Through Friction Stir Spot Welding on AA6061-T6

    by S. Suresh, J. Balaji, D. Velmurugan, Elango Natarajan, S. Sudhagar, R. Elayaraja

  • Mechanical and dynamic performance of stainless steel and nylon mesh reinforced hybrid kevlar/glass fiber composites

    by G Rajamurugan, R Elayaraja, Amod Paba, Samarjeet Singh, Vinayak Vir Singh, M Arul Murugan

    This research details an extensive experimental examination of the mechanical and dynamic properties of hybrid composites strengthened with E-glass and Kevlar fibers, and further improved with SS 304 stainless steel and nylon mesh. Four laminate configurations were fabricated via hand lay-up techniques, with variations in stacking sequences like C1- Glass fiber 2 layer/Nylon mesh/Glass fiber 2 layer/SS 304 wire mesh/Glass fiber 2 layer, C2- Kevlar fiber 2 layer/Nylon mesh/Kevlar fiber 2 layer/SS 304 wire mesh/Kevlar fiber 2 layer, C3- Glass fiber 2 layer/Nylon mesh/Kevlar fiber 2 layer/SS 304 wire mesh/Glass fiber 2 layer, C4- Kevlar fiber 2 layer/Nylon mesh/Glass fiber 2 layer/SS 304 wire mesh/Kevlar fiber 2 layer. Composite C1, outperforming all other specimens tested, had impressive flexural strength (505.89 MPa), Vickers hardness (24.76 HRM), and tensile strength (199.67 MPa). The composite with the greatest impact energy absorption was C3, which measured 4.76 J. Data from DMA showed that C1 had better viscoelastic characteristics than other materials. It was very stiff and thermally stable, with a storage modulus of up to 5000 MPa and a glass transition temperature close to 80 °C. Microstructural analyses with field emission scanning electron microscopy and energy dispersive x-ray spectroscopy verified the homogeneity of the reinforcement phases and the durability of the fiber-matrix adhesion. These results demonstrate the promise of mesh-reinforced Kevlar-glass hybrid composites for structural uses requiring extreme heat resistance, toughness, and strength.