JNJunhao Niu

Junhao Niu

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Junhao Niu has a total of 11 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Dynamic PB metasurface for transmissive and reflective wavefront manipulation

    by Yihan Wang, Chunhui Li, Junhao Niu

    Based on the phase transition characteristics of vanadium dioxide (changes in conductivity with temperature), we designed a dynamic metasurface for wavefront manipulation that can switch between transmission and reflection modes at the same frequency. When vanadium dioxide is in the metallic state, the metasurface operates in reflection mode, while it is in the insulating state, it works in transmission mode. The phase distributions of the two operating modes are different and can be easily adjusted by rotating the inner and outer rings. At the frequency of 1.3 THz, we designed a metasurface that can switch between anomalous reflection and refraction with different deflection angles. Additionally, we created a switchable metalens that provides different focal lengths in reflection and transmission modes. The tunable metasurface can provide innovative design possibilities for dynamical wavefront manipulation.


  • Open Access

    A predictive Algorithm for Boost PFC Operating in Mixed Conduction Mode

    by Junhao Niu, Hongtang Miao

    The traditional PFC control adopts the PI algorithm of the double-loop structure, but the PI parameter designed at this time is aimed at the inductor current continuous mode (CCM). When the PFC enters a heavy or light load, the converter inevitably enters the inductor current discontinuous mode (DCM). If the control parameters of CCM are still used at this time, the system may become unstable and reduce load response speed. Therefore, an optimized predictive current control is proposed, which calculates the duty cycle in CCM and DCM separately in advance, and then adopts the corresponding optimal duty cycle according to the detected inductor current conduction mode. With this algorithm, the PFC can operate in mixed conduction mode. It has a wider load range and faster load response speed than PI. Finally, through PLECS, the algorithm is verified by simulation.


  • Open Access

    Surface plasmon polaritons broadband band-stop filter based on EIT effect modulation

    by Junhao Niu, Weiyu Luo, Aijun Zhu, Jiajie Wang, Benxin Zhang

    The filter is one of the most important key elements of electronic circuit. With the rapid development of information, traditional electrical filters can no longer meet the requirements of fast information processing speed and low loss. All optical information processing is considered as one of the solutions to solve this problem. Therefore, there is great significance for studying the all-optical filter. Here, we put forward a kind of broadband band-stop filter which based on surface plasmon polaritons (SPPs) metal - insulator - metal (MIM) modulating by electromagnetically induced transparency (EIT) resonance. We use the finite element method for numerical simulation, and further research on the factors influencing the transmission characteristics of this structure by adjusting the geometric structure. Compared with similar SPPs-based filters, the proposed structure realizes broad stopband, and we can change the EIT resonance to modulate the band-stop filter wavelength range. The proposed broadband band-stop filter based on EIT effect modulation may have great potential in the next generation of all-optical information processing and communication.


  • Design and implementation of fault simulation device for micro ring resonator based on SGM3157

    by Zhu Aijun, Zhao Chunxia, Niu Junhao, Liang Zhixun, Hu Cong, Xu Chuanpei

    Photonic Network-On-Chip (PNOC) has become a new research frontier and hot spot in multidisciplinary intersecting. Micro ring resonator (MRR) is a key device in PNOC. However, MRR is very sensitive to the fluctuation of temperature, and it is easy to be faulty, resulting in a sharp decline of performance and reliability in PNOC. Therefore, MRR fault detection has become a very important and urgent problem. How to detect MRR fault is the key to improve the reliability of PNOC, and the MRR fault simulator is the key to verify the MRR fault detection. To the best of our knowledge, there is little work so far to tackle MRR fault simulators issues. First of all, this paper designs the fault model of MRR, and then gives the design principle of MRR fault simulator. The designed device can be divided into four parts: fault simulator module, fault processing module, display module and fault setting module. The experimental results demonstrate that the proposed device can realize the arbitrary setting of the fault location of MRR, switching of different fault simulator module and fault judgment and display. The experimental results prove the validity of the fault simulator designed in this paper.