Mingchun Wang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Mingchun Wang has a total of 28 co-authors. Here are the top co-authors by number of shared publications:
- Zixiao Xing
CNOOC Research Institute, Beijing 100028, China
3 shared publications - Guoqing Han
College of Petroleum Engineering, China University of Petroleum, Beijing 102249, China
2 shared publications - Tianhao Wang
CNOOC Research Institute, Beijing 100028, China
2 shared publications - Xinrui Zhang
CNOOC Research Institute, Beijing 100028, China
2 shared publications - Yuchen Ji
National Key Laboratory of Offshore Oil and Gas Exploitation, Beijing 102209, China
2 shared publications - Yupei Liu
CNOOC Research Institute, Beijing 100028, China
2 shared publications
Latest Publications
- Open Access
Research on Optimization Method of Operating Parameters for Electric Submersible Pumps Based on Multiphase Flow Fitting
Electric submersible pumps (ESPs) are among the most widely used artificial lifting systems, and their operational stability is crucial to the production capacity and lifespan of oil wells. However, during the operation of ESP systems, they often face complex flow issues such as gas lock and insufficient liquid carry. Traditional control strategies relying on liquid level monitoring and electrical parameter alarms exhibit obvious latency, making it difficult to effectively guide the adjustments of key operating parameters such as pump frequency, valve opening, and on/off strategies. To monitor the flow state of ESP systems and optimize it in a timely manner, this paper proposes an innovative profile recognition method based on multiphase flow fitting in the wellbore, aimed at reconstructing the flow state at the pump’s intake. This method identifies flow abnormalities and, in conjunction with flow characteristics, designs targeted operating parameter optimization logic to enhance the stability and efficiency of ESP systems. Research shows that this optimization method can significantly improve the pump’s operational performance, reduce failure rates, and extend equipment lifespan, thus providing an effective solution for optimizing production in electric pump wells. Additionally, this method holds significant importance for enhancing oil well production efficiency and economic benefits, providing a scientific theoretical foundation and practical guidance for future oil and gas exploration and management.
Open AccessResearch on Optimization Method of Operating Parameters for Electric Submersible Pumps Based on Multiphase Flow Fitting
Electric submersible pumps (ESPs) are among the most widely used artificial lifting systems, and their operational stability is crucial to the production capacity and lifespan of oil wells. However, during the operation of ESP systems, they often face complex flow issues such as gas lock and insufficient liquid carry. Traditional control strategies relying on liquid level monitoring and electrical parameter alarms exhibit obvious latency, making it difficult to effectively guide the adjustments of key operating parameters such as pump frequency, valve opening, and on/off strategies. To monitor the flow state of ESP systems and optimize it in a timely manner, this paper proposes an innovative profile recognition method based on multiphase flow fitting in the wellbore, aimed at reconstructing the flow state at the pump’s intake. This method identifies flow abnormalities and, in conjunction with flow characteristics, designs targeted operating parameter optimization logic to enhance the stability and efficiency of ESP systems. Research shows that this optimization method can significantly improve the pump’s operational performance, reduce failure rates, and extend equipment lifespan, thus providing an effective solution for optimizing production in electric pump wells. Additionally, this method holds significant importance for enhancing oil well production efficiency and economic benefits, providing a scientific theoretical foundation and practical guidance for future oil and gas exploration and management.
- Open Access
Dynamic Fitting Method for Wellbore Multiphase Flow with Exponentially Weighted Parameter Updating
Accurate dynamic characterization of wellbore multiphase flow is fundamental for production optimization and real-time control in oil and gas wells. Addressing technical constraints of existing dynamic fitting methods, this study proposes a novel dynamic fitting methodology integrating physical mechanisms with exponentially weighted parameter updating. The approach leverages multiphase flow theory to target the liquid holdup factor and friction factor as correction parameters for dynamic fitting. It incorporates Particle Swarm Optimization to achieve rapid and accurate fitting and introduces an Exponentially Weighted Moving Average mechanism to dynamically update parameters. By fusing historical data with real-time data, the Exponentially Weighted Moving Average method balances instantaneous responsiveness with long-term stability. Empirical validation using a dataset from Block XX of a Southern China oilfield demonstrates the superior accuracy of the fitting method under low-to-medium frequency data conditions. During data interruptions or anomalous disturbances, the method maintains high accuracy while exhibiting a low mean relative change percentage; it effectively suppressed the non-physical jumps of the fitting coefficients and maintained stable and accurate fitting.
Open AccessDynamic Fitting Method for Wellbore Multiphase Flow with Exponentially Weighted Parameter Updating
Accurate dynamic characterization of wellbore multiphase flow is fundamental for production optimization and real-time control in oil and gas wells. Addressing technical constraints of existing dynamic fitting methods, this study proposes a novel dynamic fitting methodology integrating physical mechanisms with exponentially weighted parameter updating. The approach leverages multiphase flow theory to target the liquid holdup factor and friction factor as correction parameters for dynamic fitting. It incorporates Particle Swarm Optimization to achieve rapid and accurate fitting and introduces an Exponentially Weighted Moving Average mechanism to dynamically update parameters. By fusing historical data with real-time data, the Exponentially Weighted Moving Average method balances instantaneous responsiveness with long-term stability. Empirical validation using a dataset from Block XX of a Southern China oilfield demonstrates the superior accuracy of the fitting method under low-to-medium frequency data conditions. During data interruptions or anomalous disturbances, the method maintains high accuracy while exhibiting a low mean relative change percentage; it effectively suppressed the non-physical jumps of the fitting coefficients and maintained stable and accurate fitting.
- Open Access
The Casing Collapse Mechanism in Salt Formations in Deepwater Fields in Brazil
Salt formations are commonly encountered during oil and gas drilling. Due to the rheological properties of salt rocks, casing collapse accidents happen frequently. Under action of nonuniform geostress, casing failure has become an important influencing factor that restricts the exploration and development benefits of deep and ultra-deep wells. Casing stress in a period after well cementation in the salt formation of Brazilian deepwater fields was analyzed. Results show that the nonuniform geostress is instantaneously applied on the cement sheath when well cementation is completed in the salt formation and then transferred to the casing. Stress on the inner wall grows with an increase in the angle with the direction of the maximum horizontal principal stress and it reaches the maximum in the direction of the minimum horizontal principal stress. As the creep continues, stress on the inner wall of casings gradually enlarges and the circumferential stress in inner rings tends to be uniform, which means that creep of the formation weakens the nonuniformity of casing deformation. The collapse pressure on the outer wall of casings tends to increase at first and then decrease as the angle with the direction of maximum horizontal principal stress enlarges. Stress on the inner wall of casings in the salt formation reduces with the increasing thickness of casings selected, and the casing strength is improved as the wall thickness increases. The research results provide certain theoretical guidance for the strength check of casings in well cementation engineering in salt formations.
Open AccessThe Casing Collapse Mechanism in Salt Formations in Deepwater Fields in Brazil
Salt formations are commonly encountered during oil and gas drilling. Due to the rheological properties of salt rocks, casing collapse accidents happen frequently. Under action of nonuniform geostress, casing failure has become an important influencing factor that restricts the exploration and development benefits of deep and ultra-deep wells. Casing stress in a period after well cementation in the salt formation of Brazilian deepwater fields was analyzed. Results show that the nonuniform geostress is instantaneously applied on the cement sheath when well cementation is completed in the salt formation and then transferred to the casing. Stress on the inner wall grows with an increase in the angle with the direction of the maximum horizontal principal stress and it reaches the maximum in the direction of the minimum horizontal principal stress. As the creep continues, stress on the inner wall of casings gradually enlarges and the circumferential stress in inner rings tends to be uniform, which means that creep of the formation weakens the nonuniformity of casing deformation. The collapse pressure on the outer wall of casings tends to increase at first and then decrease as the angle with the direction of maximum horizontal principal stress enlarges. Stress on the inner wall of casings in the salt formation reduces with the increasing thickness of casings selected, and the casing strength is improved as the wall thickness increases. The research results provide certain theoretical guidance for the strength check of casings in well cementation engineering in salt formations.
- Open Access
Experimental Study on the Transport Behavior of Micron-Sized Sand Particles in a Wellbore
In the process of natural gas hydrate extraction, especially in offshore hydrate extraction, the multiphase flow inside the wellbore is complex and prone to flow difficulties caused by reservoir sand production, leading to pipeline blockage accidents, posing a threat to the safety of hydrate extraction. This paper presents experimental research on the migration characteristics of micrometer-sized sand particles entering the wellbore, detailing the influence of key parameters such as sand particle size, sand ratio, wellbore deviation angle, fluid velocity, and fluid viscosity on the sand bed height. It establishes a predictive model for the deposition height of micrometer-sized sand particles. The model’s predicted results align well with experimental findings, and under the experimental conditions of this study, the model’s average prediction error for the sand bed height is 12.47%, indicating that the proposed model demonstrates a high level of accuracy in predicting the bed height. The research results can serve as a practical basis and engineering guidance for reducing the risk of natural gas hydrate and sand blockages, determining reasonable extraction procedures, and ensuring the safety of wellbore flow.
Open AccessExperimental Study on the Transport Behavior of Micron-Sized Sand Particles in a Wellbore
In the process of natural gas hydrate extraction, especially in offshore hydrate extraction, the multiphase flow inside the wellbore is complex and prone to flow difficulties caused by reservoir sand production, leading to pipeline blockage accidents, posing a threat to the safety of hydrate extraction. This paper presents experimental research on the migration characteristics of micrometer-sized sand particles entering the wellbore, detailing the influence of key parameters such as sand particle size, sand ratio, wellbore deviation angle, fluid velocity, and fluid viscosity on the sand bed height. It establishes a predictive model for the deposition height of micrometer-sized sand particles. The model’s predicted results align well with experimental findings, and under the experimental conditions of this study, the model’s average prediction error for the sand bed height is 12.47%, indicating that the proposed model demonstrates a high level of accuracy in predicting the bed height. The research results can serve as a practical basis and engineering guidance for reducing the risk of natural gas hydrate and sand blockages, determining reasonable extraction procedures, and ensuring the safety of wellbore flow.
- Open Access
- 23 April 2024
- Published by Frontiers Media SA in Frontiers in Energy Research
- Vol. 12, 1392272
The shrinkage behavior of boreholes drilled through deepwater creeping salt formations in West Africa
Introduction: Salt formations are complex and pose significant risks during oil and gas drilling. Creep behavior in salt formations under geostress can jeopardize drilling safety.Methods: This study analyzes the shrinkage behavior of boreholes drilled through salt formations in West Africa’s Block B, with emphasis on the differential creep rates in two horizontal principal stress directions and the evolution of wellbore shape over time. The impact of drilling fluid density on shrinkage rates is also investigated.Results: After drilling through salt formations, the creep rates differ between the two horizontal principal stress directions. Shrinkage is faster in the direction of minimum horizontal principal stress and slower in the direction of maximum horizontal principal stress. Over time, shrinkage rates converge, resulting in a transition from elliptical to circular wellbore shape. Higher drilling fluid density leads to reduced shrinkage rates.Discussion: These findings contribute to the theoretical guidance for drilling fluid density selection in salt formations.
- 23 April 2024
- Published by Frontiers Media SA in Frontiers in Energy Research
- Vol. 12, 1392272
Open AccessThe shrinkage behavior of boreholes drilled through deepwater creeping salt formations in West Africa
Introduction: Salt formations are complex and pose significant risks during oil and gas drilling. Creep behavior in salt formations under geostress can jeopardize drilling safety.Methods: This study analyzes the shrinkage behavior of boreholes drilled through salt formations in West Africa’s Block B, with emphasis on the differential creep rates in two horizontal principal stress directions and the evolution of wellbore shape over time. The impact of drilling fluid density on shrinkage rates is also investigated.Results: After drilling through salt formations, the creep rates differ between the two horizontal principal stress directions. Shrinkage is faster in the direction of minimum horizontal principal stress and slower in the direction of maximum horizontal principal stress. Over time, shrinkage rates converge, resulting in a transition from elliptical to circular wellbore shape. Higher drilling fluid density leads to reduced shrinkage rates.Discussion: These findings contribute to the theoretical guidance for drilling fluid density selection in salt formations.