TATadashi Ariga

Tadashi Ariga

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Tadashi Ariga has a total of 69 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Brazing of Copper Foam Using Cu-4.0Sn-9.9Ni-7.8P Filler Foil: Effect of Brazing Temperature and Copper Foam Pore Density

    by Nur Amirah Mohd Zahri, Yukio Miyashita, Tadashi Ariga, A.S.M. Abdul Haseeb, Nazatul Liana Sukiman

    Copper (Cu) foam is a promising material that owns a high surface area that can be utilized in a thermal application. In this research, the brazing of Cu substrate to Cu foam in the sandwich configuration using Cu alloy filler foil was carried out. The foam at different pore per inch (PPI) of 15, 25 and 50 are brazed at different brazing temperatures. Mechanical and microstructure analysis were conducted to investigate a suitable brazing temperature and the best pore density of foam. The compressive strength of brazed 50 PPI foam has yielded the highest due to the highly dense interconnected branches. While the highest shear strength of brazed interface using 15 PPI foam has been recorded. The large branch size of 15 PPI foam has contributed to the sound joint between the brazed joint interface of Cu substrate and foam. Both mechanicals analysis above exhibits a highest strength at 660 °C as a brazing temperature The shear stress-strain curve of Cu substrate and foam brazed joint interface shows a brittle behaviour which accordance with the discoverable brittle phases of Cu3P and Ni3P using X-ray diffraction (XRD). Scanning electron microscopy (SEM) and Energy dispersive X-ray spectroscopy (EDX) have presented the formation of Cu3P and Ni3P at the brazed joint interface of Cu substrate and foam.

  • Brazing of Porous Nickel to Copper and Stainless Steel: Microstructure and Mechanical Properties

    by Tuan Zaharinie, Muhammad Amirul Ikmal, Ramizah Rozaimay, Tadashi Ariga

    A porous nickel (Ni) was brazed to copper (Cu) and stainless steel 304 (SS304) using VZ2250 and MBF67 brazing filler metal with a composition of 77.4Cu-9.3Sn-7.0Ni-6.3P and 64.5Ni-25Cr-6P-1.5Si (Cu: Copper, Sn: Tin, Ni: Nickel, P: Phosphorus, Cr: Chromium, Si: Silicon), respectively for joint microstructure and mechanical properties analysis. Porous Ni with a pore density of 15 pores per inch (PPI) was sandwiched between Cu/VZ2250 and MBF67/SS304. A brazed joint of Cu/Porous Ni/SS304 with VZ2250 and MBF67 brazing filler metal was prepared in a high vacuum furnace at different brazing times of 5, 10, and 15 minutes for 1015 °C with a heating and cooling rate of 10 °C/min, respectively for comparison purpose. The microstructure and mechanical properties of the brazed joint were investigated to identify the joint ability after the brazing process. Scanning Electron Microscope (SEM) equipped with Energy Dispersive X-Ray Spectroscopy (EDS) confirmed the interfacial microstructure by the formation of the diffusion filler metal (dark grey colour) for the Cu/Porous Ni/SS304 with VZ2250 and MBF67 brazing filler metal. For shear strength tests, the value decreases with an increase in the brazing time. The shear strength tests for the brazed joint of Cu/Porous Ni/SS304 with VZ2250 and MBF67 brazing filler metal show the maximum shear strength test value can be achieved for the brazing time of 5 minutes. The decreasing shear strength value was observed with differences in structural data of porous Ni due to the softening after the brazing process. Keywords: Brazing, Microstructure, Porous Nickel, Shear Strength.


  • Open Access

    A de novo dominant-negative variant is associated with OTULIN-related autoinflammatory syndrome

    by Yukiko Takeda, Masahiro Ueki, Junpei Matsuhiro, Erik Walinda, Takayuki Tanaka, Masafumi Yamada, Hiroaki Fujita, Shunichiro Takezaki, Ichiro Kobayashi, Sakura Tamaki, et al.

    OTULIN-related autoinflammatory syndrome (ORAS), a severe autoinflammatory disease, is caused by biallelic pathogenic variants of OTULIN, a linear ubiquitin-specific deubiquitinating enzyme. Loss of OTULIN attenuates linear ubiquitination by inhibiting the linear ubiquitin chain assembly complex (LUBAC). Here, we report a patient who harbors two rare heterozygous variants of OTULIN (p.P152L and p.R306Q). We demonstrated accumulation of linear ubiquitin chains upon TNF stimulation and augmented TNF-induced cell death in mesenchymal stem cells differentiated from patient-derived iPS cells, which confirms that the patient has ORAS. However, although the de novo p.R306Q variant exhibits attenuated deubiquitination activity without reducing the amount of OTULIN, the deubiquitination activity of the p.P152L variant inherited from the mother was equivalent to that of the wild-type. Patient-derived MSCs in which the p.P152L variant was replaced with wild-type also exhibited augmented TNF-induced cell death and accumulation of linear chains. The finding that ORAS can be caused by a dominant-negative p.R306Q variant of OTULIN furthers our understanding of disease pathogenesis.


  • Changes in bone turnover markers after discontinuing long-term glucocorticoid administration in children with idiopathic nephrotic syndrome: a multicenter retrospective observational study

    by Yasuhiro Ueda, Takayuki Okamoto, Yasuyuki Sato, Asako Hayashi, Toshiyuki Takahashi, Ryota Suzuki, Hayato Aoyagi, Michihiko Ueno, Norio Kobayashi, Kimiaki Uetake, et al.

    Background Glucocorticoids affect bone turnover. Little is known about how bone turnover changes when glucocorticoids are discontinued following long-term administration. Methods This retrospective observational study was conducted on the relationship between discontinuation of long-term administration of glucocorticoid and bone turnover markers (BTMs) in patients with childhood-onset idiopathic nephrotic syndrome. Serum bone alkaline phosphatase (BAP), intact procollagen type 1 N-terminal propeptide (P1NP), and tartrate-resistant acid phosphatase-5b (TRACP-5b) were evaluated as BTMs. Results Thirty-eight pairs of BTMs at glucocorticoid administration and after discontinuation were analyzed in 29 patients. The median age at baseline was 12.4 (interquartile range, 9.0–14.5) years, and the median time from the onset of nephrotic syndrome was 5.9 (3.3–9.7) years. The mean period from prednisolone discontinuation to the measurement of BTMs after glucocorticoid discontinuation was 3.5 ± 1.0 months. Changes in BTMs after glucocorticoid discontinuation were modest when the daily prednisolone dose was < 0.25 mg/kg/day (ln BAP standard deviation [SD] score, p = 0.19; log intact P1NP SD score, p = 0.70; TRACP-5b, p = 0.95). When the daily prednisolone dose was ≥ 0.25 mg/kg/day, all BTMs increased significantly after glucocorticoid discontinuation (ln BAP SD score, p < 0.01; log intact P1NP SD score, p < 0.01; TRACP-5b, p < 0.01). Conclusions Decreased BTMs can rise within a few months of discontinuing long-term glucocorticoid administration. When the administered glucocorticoid dose is low, changes in BTMs may be small. Graphical abstract A higher resolution version of the Graphical abstract is available as Supplementary information


  • Open Access

    Effect of Laser Surface Modification (LSM) on laser energy absorption for laser brazing

    by A Q Zaifuddin, M H Aiman, M M Quazi, Mahadzir Ishak, T Ariga

    Since the development of the laser in the 1960s a rapid development of research interests in science and technology took place. Since then, the need of laser application in industrials such as automotive, aerospace and electronics is increasing because of several advantages like automation worthiness, noncontact processing and product quality improvement. In this present study, the effect of Laser Surface Modification (LSM) on pure copper plate towards the laser energy absorption during indirect laser brazing process was studied. The laser brazing experiment was conducted inside a chamber under controlled vacuum pressure with 400Pa and irradiated with constant 140 Watt laser power. The defocusing features for laser brazing was used in order to find better focal position. Accordingly, the focal length for this laser brazing experiment was set to the focus point at 124 mm from the focal plane. Meanwhile, during LSM process, laser parameters such as laser scanning speed and focus length have been kept constant throughout the surface modification process. Yet, the laser power and laser frequency have been varied from 9 Watt to 27 Watt and 10 kHz to 80 kHz respectively. Apparently, surface roughness due to surface removal and oxide layer formation were presented during LSM process. These two surface integrities were found to be the factors of increasing laser energy absorption. It was discovered that an increase in surface roughness and oxide layer formation can absorb more laser energy which then results an increase in brazing temperature during laser brazing. This is because, increasing surface roughness will scatter the laser energy over a larger surface area, multiply the reflections in the surface irregularities while the oxide layer will enhance the interference phenomena of laser energy occurring inside the oxide layer. Both mechanisms increase laser energy absorptivity during laser brazing which results a high brazing temperature.


  • Evaluation of systemic activity of pediatric primary Sjögren’s syndrome by EULAR Sjögren’s syndrome disease activity index (ESSDAI)

    by Ichiro Kobayashi, Yuka Okura, Masahiro Ueki, Yusuke Tozawa, Shunichiro Takezaki, Masafumi Yamada, Tadashi Ariga

    Objectives: The purpose of this study is to evaluate systemic disease activity of pediatric Sjögren’s syndrome (SS) using European League Against Rheumatism (EULAR) Sjögren’s syndrome disease activity index (ESSDAI). Methods: We retrospectively reviewed medical records of patients with SS who have been diagnosed according to 1999 Japanese diagnostic criteria for SS before 16 years old at KKR Sapporo Medical Center, Hokkaido University Hospital, and affiliated hospitals. We analyzed clinical and laboratory data and calculated ESSDAI at both diagnosis and peak activity. Results: Twenty-five patients (2 boys and 23 girls) were enrolled. Only 4 patients had sicca symptoms at diagnosis. Mean ESSDAI scores at diagnosis and peak activity were 12.68 (2–31) and 15.08 (2–38), respectively. Only 3 patients were inactive (ESSDAI score <5) at diagnosis. Frequently involved domains at diagnosis were the biological (96%) followed by the constitutional (68%), glandular (44%), articular (44%), cutaneous domains (28%), renal (16%), and central nervous system (12%). At peak activity, biological domain (96%) was followed by the constitutional (72%), glandular (60%), articular (44%), cutaneous (28%), central nervous system (20%), and renal domains (16%). Conclusion: Pediatric SS is suspected from active systemic manifestations. The items of ESSDAI are useful clues to the diagnosis of pediatric SS.


  • Difficulty in the diagnosis of bone and joint pain associated with pediatric acute leukemia; comparison with juvenile idiopathic arthritis

    by Takao Tsujioka, Minako Sugiyama, Masahiro Ueki, Yusuke Tozawa, Shunichiro Takezaki, Junjiro Ohshima, Yuko Cho, Masafumi Yamada, Akihiro Iguchi, Ichiro Kobayashi, et al.

    Acute leukemia often causes osteoarthralgia. The aim of this study is characterization of leukemia-associated osteoarthralgia in comparison with juvenile idiopathic arthritis (JIA). We retrospectively reviewed clinical records of 31 patients with acute leukemia and 13 patients with articular JIA diagnosed between January 2008 and March 2013. Clinical and laboratory findings at the initial examination were compared among the three groups; 10 leukemia with and 21 leukemia without osteoarthralgia and 13 JIA groups. Eleven of the 31 leukemic patients (35%) had osteoarthralgia before the diagnosis of leukemia. Peripheral leukemic cells were initially absent in 10 of the 31 leukemia patients including three with osteoarthralgia. Platelet counts over 300 × 109/L were common in JIA, but not in osteoarthralgia group. Mean serum lactate dehydrogenase levels were higher in both of the leukemia groups than JIA group but often within normal or near-normal levels in the leukemia groups. Magnetic resonance imaging was examined in three leukemic patients and demonstrated osteomyelitis-like bone marrow edema in two and periarticular infiltration similar to synovitis in one patient. Three leukemic patients with osteoarthralgia showed partial and transient responses to antibiotic therapy. Leukemia-associated osteoarthralgia is often indistinguishable from rheumatic diseases by imaging and laboratory findings and should be confirmed by bone marrow examination.


  • Graft‐versus‐host disease (GVHD) prophylaxis by using methotrexate decreases pre‐engraftment syndrome and severe acute GVHD, and accelerates engraftment after cord blood transplantation

    by Akihiro Iguchi, Yukayo Terashita, Minako Sugiyama, Junjiro Ohshima, Tomonobu Z. Sato, Yuko Cho, Ryoji Kobayashi, Tadashi Ariga

    GVHD and graft failure are serious problems in CBT. PES after CBT also occurs frequently and is associated with transplantation‐related complications such as acute GVHD. We reviewed medical records for 70 consecutive child CBT recipients between December 1997 and April 2015. Forty‐nine patients received prophylaxis against GVHD with CsA or Tac in combination with mPSL from day +7 (mPSL group), and 21 patients received CsA or Tac with MTX on day +1 and day +3 (MTX group). Neutrophil engraftment was detected in 59 patients (84.3%). Neutrophil engraftment rate in the MTX group was significantly higher than that in the mPSL group (21/21 (100%) and 38/49 (77.6%), respectively, p = 0.027). PES developed in 35 patients, and the incidence of PES in the mPSL group was significantly higher than that in the MTX group (p = 0.036). The incidence of severe acute GVHD (grade III or IV) in the MTX group was significantly lower than that in the mPSL group (p = 0.049). Although this study was a small‐scale study, the results showed that increase in the rate of engraftment and decrease in the incidence of early immune reactions such as PES and severe acute GVHD could be achieved by early commencement of immunosuppression using MTX.


  • Microstructural stability of Sn–1Ag–0.5Cu–xAl (x=1, 1.5, and 2wt.%) solder alloys and the effects of high-temperature aging on their mechanical properties

    by Mohd Faizul Mohd Sabri, Dhafer Abdulameer Shnawah, Irfan Anjum Badruddin, Suhana Binti Mohd Said, Fa Xing Che, Tadashi Ariga


  • Open Access

    Wettability of Lead-Free Solders on Gold-Plated Copper Substrates

    by Ngoc Binh Duong, Tadashi Ariga, Luay Bakir Hussain, Amad Badri Ismail

    Japan's largest platform for academic e-journals: J-STAGE is a full text database for reviewed academic papers published by Japanese societies