Tz-Wun Wang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Tz-Wun Wang has a total of 26 co-authors. Here are the top co-authors by number of shared publications:
- Ke-Horng Chen
National yang Ming Chiao Tung University
9 shared publications Shian-Ru Lin
RealTek Semiconductor Corporation, Hsinchu, Taiwan
8 shared publicationsTsung-Yen Tsai
RealTek Semiconductor Corporation, Hsinchu, Taiwan
8 shared publicationsYing-Hsi Lin
RealTek Semiconductor Corporation, Hsinchu, Taiwan
8 shared publications- Chi-Yu Chen
Institute of Electrical and Computer Engineering, National Yang Ming Chiao Tung University, Hsinchu, Taiwan
7 shared publications - Po-Jui Chiu
Institute of Electrical and Computer Engineering, National Yang Ming Chiao Tung University, Hsinchu, Taiwan
7 shared publications
Latest Publications
- 1 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 61 (10) , 1-13
A Capacitor-Free Hybrid-Process Low Dropout Regulator With Ultrahigh-Gain Amplifier and Super Source Follower for 0.297 mV/A Load Regulation and 0.024 mV/V Line Regulation
- 1 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 61 (10) , 1-13
A Capacitor-Free Hybrid-Process Low Dropout Regulator With Ultrahigh-Gain Amplifier and Super Source Follower for 0.297 mV/A Load Regulation and 0.024 mV/V Line Regulation
- 2 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 41 (5) , 7270-7281
A Dynamic-R ON -Reduced Bidirectional GaN Load Switch With Inrush Current Protection and Spike Suppression
The proposed bidirectional load switch enables bidirectional current conduction while effectively blocking reverse current, providing efficient and reliable power management. It operates with a maximum input voltage (${V}_{\text{IN}}$) of 48 V and supports load currents (${I}_{\text{Load}}$) up to 25 A, achieving a low on-resistance (${R}_{\text{on}}$) of 11.2 mΩ. A driving current limiter is implemented to regulate the gate-driving strength and suppress inrush current, allowing the bidirectional GaN (Bi-GaN) switch to turn on smoothly. This results in a rising propagation delay (${T}_{\text{pdr}}$) of 347.4 μs and a rise time (${T}_{r}$) of 936.7 μs, reducing inrush current by 91.4%. Additionally, the spike-reduced turn-off circuit enables fast turn-off with a 409.7 ns falling propagation delay (${T}_{\text{pdf}}$) and 483.6 ns fall time (${T}_{f}$), reducing voltage overshoot by 89.5% to protect on-chip devices. The Bi-GaN device also adopts a split-source field plate structure, limiting the ${R}_{\text{on}}$ increase to only 28.5% after 168 h of stress testing, thereby ensuring long-term reliability and performance stability.
- 2 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 41 (5) , 7270-7281
A Dynamic-R ON -Reduced Bidirectional GaN Load Switch With Inrush Current Protection and Spike Suppression
The proposed bidirectional load switch enables bidirectional current conduction while effectively blocking reverse current, providing efficient and reliable power management. It operates with a maximum input voltage (${V}_{\text{IN}}$) of 48 V and supports load currents (${I}_{\text{Load}}$) up to 25 A, achieving a low on-resistance (${R}_{\text{on}}$) of 11.2 mΩ. A driving current limiter is implemented to regulate the gate-driving strength and suppress inrush current, allowing the bidirectional GaN (Bi-GaN) switch to turn on smoothly. This results in a rising propagation delay (${T}_{\text{pdr}}$) of 347.4 μs and a rise time (${T}_{r}$) of 936.7 μs, reducing inrush current by 91.4%. Additionally, the spike-reduced turn-off circuit enables fast turn-off with a 409.7 ns falling propagation delay (${T}_{\text{pdf}}$) and 483.6 ns fall time (${T}_{f}$), reducing voltage overshoot by 89.5% to protect on-chip devices. The Bi-GaN device also adopts a split-source field plate structure, limiting the ${R}_{\text{on}}$ increase to only 28.5% after 168 h of stress testing, thereby ensuring long-term reliability and performance stability.
- 5 August 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 40 (12) , 17637-17649
A Monolithic GaN-Based LLC-SRC With Sub-1 mA Quiescent Current and 98.6% Peak Efficiency for Energy Star Standard and 80 Plus Titanium Standard
The proposed GaN-based hybrid gate driver consists of two types of inverters and achieves a low quiescent current (IQ) of 23.2 μA with a fast-operating frequency of 25 MHz. At the same time, the automatic precharge technique senses the voltage of the bootstrapped capacitor and reduces the standby mode leakage current (ILKG) from a few milliamps to 62 μA. Therefore, the efficiency is greater than 92% at the entire output load. Finally, the soft startup clamping technique limits the peak voltage from 2.51 kV to 620 V, reducing power consumption during soft-start and preventing 650 V GaN devices from being damaged by high-voltage stress. As a result, the LLC converter achieves a peak efficiency of 98.6% and complies with the 80 Plus Titanium and Energy Star standards for power supply units.
- 5 August 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 40 (12) , 17637-17649
A Monolithic GaN-Based LLC-SRC With Sub-1 mA Quiescent Current and 98.6% Peak Efficiency for Energy Star Standard and 80 Plus Titanium Standard
The proposed GaN-based hybrid gate driver consists of two types of inverters and achieves a low quiescent current (IQ) of 23.2 μA with a fast-operating frequency of 25 MHz. At the same time, the automatic precharge technique senses the voltage of the bootstrapped capacitor and reduces the standby mode leakage current (ILKG) from a few milliamps to 62 μA. Therefore, the efficiency is greater than 92% at the entire output load. Finally, the soft startup clamping technique limits the peak voltage from 2.51 kV to 620 V, reducing power consumption during soft-start and preventing 650 V GaN devices from being damaged by high-voltage stress. As a result, the LLC converter achieves a peak efficiency of 98.6% and complies with the 80 Plus Titanium and Energy Star standards for power supply units.
- 29 July 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 61 (4) , 1656-1667
Monolithic GaN-Based Secondary-Side Controller for Precise Dead-Time Control Enabling ZVS and ZCS
Unlocking the full potential of gallium nitride (GaN)-based rectifiers requires precise dead-time management, ensuring zero-voltage switching (ZVS) turn-on and zero-current switching (ZCS) turn-off. The proposed monolithic accurate on/off synchronous rectifier (SR) control (AOSC) improves dead-time precision and improves current sensing to minimize power loss in a 380–12-V LLC resonant flyback converter. The tri-enhancement GaN driver (TGD), incorporating three key advancements, achieves an ultra-fast switching delay of less than 3 ns, enabling rapid turn on/off of the GaN-based rectifier. Additionally, the error-eliminated GaN sensor (EGS) provides precise current sensing with a sub-1% error margin, ensuring accurate rectifier turn-off timing. This enables ZCS operation and integrates on-chip overcurrent protection (OCP). Moreover, the zero-crossing GaN detector (ZGD) compensates for controller delays, effectively minimizing reverse conduction losses. As a result, the proposed design achieves a high step-down ratio and an outstanding efficiency of 97.1%.
- 29 July 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 61 (4) , 1656-1667
Monolithic GaN-Based Secondary-Side Controller for Precise Dead-Time Control Enabling ZVS and ZCS
Unlocking the full potential of gallium nitride (GaN)-based rectifiers requires precise dead-time management, ensuring zero-voltage switching (ZVS) turn-on and zero-current switching (ZCS) turn-off. The proposed monolithic accurate on/off synchronous rectifier (SR) control (AOSC) improves dead-time precision and improves current sensing to minimize power loss in a 380–12-V LLC resonant flyback converter. The tri-enhancement GaN driver (TGD), incorporating three key advancements, achieves an ultra-fast switching delay of less than 3 ns, enabling rapid turn on/off of the GaN-based rectifier. Additionally, the error-eliminated GaN sensor (EGS) provides precise current sensing with a sub-1% error margin, ensuring accurate rectifier turn-off timing. This enables ZCS operation and integrates on-chip overcurrent protection (OCP). Moreover, the zero-crossing GaN detector (ZGD) compensates for controller delays, effectively minimizing reverse conduction losses. As a result, the proposed design achieves a high step-down ratio and an outstanding efficiency of 97.1%.
- 2 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Solid-State Circuits Letters
- Vol. 7, 359-362
A 15.4-ppm/°C GaN-Based Voltage Reference With Process-Variation-Immunity and High PSR for Electric Vehicle Power Systems
The proposed GaN-based voltage reference (VREF) generator has a low temperature coefficient (TC) of 15.4ppm/° C, small VREF deviation at different process corners (standard deviation of 0.22%), line sensitivity as low as 0.0023%/V, and high power supply rejection (PSR) of -187dB and -114dB at 100Hz and 50MHz respectively. The proportional-to-absolute-temperature (PTAT) gate current for enhancement-mode GaN (eGaN) optimizes TC. Eliminating depletion-mode GaN (dGaN) gate leakage and using multiple stacked composite dGaNs can improve line regulation and PSR. All performance is achieved with a low power consumption of 10.9μ W.
- 2 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Solid-State Circuits Letters
- Vol. 7, 359-362
A 15.4-ppm/°C GaN-Based Voltage Reference With Process-Variation-Immunity and High PSR for Electric Vehicle Power Systems
The proposed GaN-based voltage reference (VREF) generator has a low temperature coefficient (TC) of 15.4ppm/° C, small VREF deviation at different process corners (standard deviation of 0.22%), line sensitivity as low as 0.0023%/V, and high power supply rejection (PSR) of -187dB and -114dB at 100Hz and 50MHz respectively. The proportional-to-absolute-temperature (PTAT) gate current for enhancement-mode GaN (eGaN) optimizes TC. Eliminating depletion-mode GaN (dGaN) gate leakage and using multiple stacked composite dGaNs can improve line regulation and PSR. All performance is achieved with a low power consumption of 10.9μ W.
- 27 November 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 72 (1) , 420-432
Monolithic GaN-Based Multiple-Phase Bidirectional Energy Transfer With Seamless Control Applied on High-Voltage and Low-Voltage Batteries
In this paper, the proposed multi-phase (MP) bidirectional dual Gallium-Nitride (GaN) controlled rectifier (GCR) uses dual GCR with the pre-charge technique to reduce third quadrant operation by minimizing dead time to 0.12ns and 0.13ns, and lowering the negative V $_{\mathrm{DS}}$ to $-$ 0.6V and $-$ 0.8V in buck and boost operation, respectively. This work is the first research for monolithic bidirectional energy transfer with a two-switch-only topology. With the help of MP-accelerated current control and the GCR dynamic ramp generator, the voltage variation on the high-voltage (HV) side and low-voltage (LV) side can be reduced to less than 50mV and to 40mV, respectively, during buck and boost operation transitions. Moreover, the recovery time is effectively reduced and current balance between the four phases can be achieved within 7 cycles ( $=$ 350ns). The peak efficiency is as high as 95.5% and 94.2% in buck and boost operation, respectively.
- 27 November 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 72 (1) , 420-432
Monolithic GaN-Based Multiple-Phase Bidirectional Energy Transfer With Seamless Control Applied on High-Voltage and Low-Voltage Batteries
In this paper, the proposed multi-phase (MP) bidirectional dual Gallium-Nitride (GaN) controlled rectifier (GCR) uses dual GCR with the pre-charge technique to reduce third quadrant operation by minimizing dead time to 0.12ns and 0.13ns, and lowering the negative V $_{\mathrm{DS}}$ to $-$ 0.6V and $-$ 0.8V in buck and boost operation, respectively. This work is the first research for monolithic bidirectional energy transfer with a two-switch-only topology. With the help of MP-accelerated current control and the GCR dynamic ramp generator, the voltage variation on the high-voltage (HV) side and low-voltage (LV) side can be reduced to less than 50mV and to 40mV, respectively, during buck and boost operation transitions. Moreover, the recovery time is effectively reduced and current balance between the four phases can be achieved within 7 cycles ( $=$ 350ns). The peak efficiency is as high as 95.5% and 94.2% in buck and boost operation, respectively.
- 6 August 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 59 (12) , 4188-4198
98.7% Efficiency 1200–48 V LLC Converter Using Triple Step-Down Converter With One-Inductor Technique Compliant With EVSE Level 1
The proposed LLC flyback converter converts the 1200 V of the electric vehicle supply equipment (EVSE) into a 48 V battery system. The triple step-down converter with one inductor (TSDC-OL) technique converts 1200–400 V, and the transformer steps it down to 48 V. The zero-voltage switching (ZVS) mechanism is used for each switching operation and the equivalent on-resistance $R_{\text{ON}}$ is reduced to 1/4.5 times that of the existing technology. The proposed reference voltage compensator (RVC) can accurately maintain the charging current at 25 A. Since the left half-plane zero error amplifier (LZEA) contributes to the LHP zero, it ensures the stability of the RVC and prevents periodic variations. When the battery charges to 48 V, the operation switches to constant voltage (CV) mode via burst operation control (BOC) comparison with a leakage-based ultralow $I_{{Q}}$ comparator (LUC) with 2 nA $I_{{Q}}$ leakage. Finally, the proposed LLC flyback converter meets EVSE level 1 requirements in constant current (CC) mode and achieves 98.7% efficiency.
- 6 August 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 59 (12) , 4188-4198
98.7% Efficiency 1200–48 V LLC Converter Using Triple Step-Down Converter With One-Inductor Technique Compliant With EVSE Level 1
The proposed LLC flyback converter converts the 1200 V of the electric vehicle supply equipment (EVSE) into a 48 V battery system. The triple step-down converter with one inductor (TSDC-OL) technique converts 1200–400 V, and the transformer steps it down to 48 V. The zero-voltage switching (ZVS) mechanism is used for each switching operation and the equivalent on-resistance $R_{\text{ON}}$ is reduced to 1/4.5 times that of the existing technology. The proposed reference voltage compensator (RVC) can accurately maintain the charging current at 25 A. Since the left half-plane zero error amplifier (LZEA) contributes to the LHP zero, it ensures the stability of the RVC and prevents periodic variations. When the battery charges to 48 V, the operation switches to constant voltage (CV) mode via burst operation control (BOC) comparison with a leakage-based ultralow $I_{{Q}}$ comparator (LUC) with 2 nA $I_{{Q}}$ leakage. Finally, the proposed LLC flyback converter meets EVSE level 1 requirements in constant current (CC) mode and achieves 98.7% efficiency.
- 23 April 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 59 (8) , 2581-2590
A High Common-Mode Transient Immunity GaN-on-SOI Gate Driver With Quad-Drive Control Technique for High dV/dt 1700-V SiC Power Switch
This article proposes a gallium nitride (GaN)-based isolated silicon carbide (SiC) MOSFET gate driver with an on-chip metal–insulator–metal (MIM) capacitor that has high data rate and low propagation delay. The improved common-mode transient immunity (CMTI) envelope detection technique eliminates the common-mode current ( $I_{\mathrm{CM}})$ to improve the CMTI. In addition, the proposed isolated gate driver (IGD) with quad-drive control (QDC) technique reduces power loss and gate ringing effect. Experimental results show that the proposed IGD can achieve a slew rate of 109 kV/ $\mu$ s. At a switching frequency of 100 kHz, the efficiency of the half-bridge isolated dc–dc converter can be kept higher than 90% when $V_{\mathrm{IN}}$ changes from 800 to 1700 V, and the peak efficiency is 98.6% when $V_{\mathrm{IN}}$ $=$ 800 V.
- 23 April 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 59 (8) , 2581-2590
A High Common-Mode Transient Immunity GaN-on-SOI Gate Driver With Quad-Drive Control Technique for High dV/dt 1700-V SiC Power Switch
This article proposes a gallium nitride (GaN)-based isolated silicon carbide (SiC) MOSFET gate driver with an on-chip metal–insulator–metal (MIM) capacitor that has high data rate and low propagation delay. The improved common-mode transient immunity (CMTI) envelope detection technique eliminates the common-mode current ( $I_{\mathrm{CM}})$ to improve the CMTI. In addition, the proposed isolated gate driver (IGD) with quad-drive control (QDC) technique reduces power loss and gate ringing effect. Experimental results show that the proposed IGD can achieve a slew rate of 109 kV/ $\mu$ s. At a switching frequency of 100 kHz, the efficiency of the half-bridge isolated dc–dc converter can be kept higher than 90% when $V_{\mathrm{IN}}$ changes from 800 to 1700 V, and the peak efficiency is 98.6% when $V_{\mathrm{IN}}$ $=$ 800 V.
- 20 February 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 65, 228-230
A Monolithic GaN-Based Driver and GaN Power HEMT with Diode-Emulated GaN Technique for 50MHz Operation and Sub-0.2ns Deadtime Control
Monolithic gallium-nitride (GaN) high-electron-mobility transistors (HEMTs) have become popular due to their low parasitic capacitance, low on-resistance (R ON ), and no reverse recovery charge loss for high-frequency and high-power-density applications [1]–[6]. However, GaN HEMTs have several process defects [7], such as trapping effect and reverse-conduction loss, which will reduce the efficiency of GaN-based converters. Referring to Fig. 14.1.1, during the deadtime, the VSW falls to negative voltage before low-side GaN HEMT (Q L ) becomes conductive. Even without a body diode, Q L will experience “self-commutation loss” when the voltage difference between its gate and drain exceeds the threshold voltage (V TH, E(650V) ). The overall efficiency decreases since GaN HEMTs have higher source-to-drain voltage drop (V SD ) as compared to the body diode voltage of silicon MOSFETs. Although the power converter presented in [5] uses adaptive deadtime control to achieve a 3% efficiency improvement, due to the unpredictable delay of discrete control, the load-dependent deadtime is still not well controlled. Moreover, considering high switching operation, high dVsw/dt will cause gate ringing problem in switching period. At bottom middle of Fig. 14.1.1, the conventional negative turn-off gate bias and high drain voltage will cause a large electric field between gate and drain, thereby inducing serious trapping effect (bottom left of Fig. 14.1.1). The monolithic GaN driver with adaptive source current (I lCTRL ) does not consider the parasitic effects during turn-off period (bottom right of Fig. 14.1.1) [1].
- 20 February 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 65, 228-230
A Monolithic GaN-Based Driver and GaN Power HEMT with Diode-Emulated GaN Technique for 50MHz Operation and Sub-0.2ns Deadtime Control
Monolithic gallium-nitride (GaN) high-electron-mobility transistors (HEMTs) have become popular due to their low parasitic capacitance, low on-resistance (R ON ), and no reverse recovery charge loss for high-frequency and high-power-density applications [1]–[6]. However, GaN HEMTs have several process defects [7], such as trapping effect and reverse-conduction loss, which will reduce the efficiency of GaN-based converters. Referring to Fig. 14.1.1, during the deadtime, the VSW falls to negative voltage before low-side GaN HEMT (Q L ) becomes conductive. Even without a body diode, Q L will experience “self-commutation loss” when the voltage difference between its gate and drain exceeds the threshold voltage (V TH, E(650V) ). The overall efficiency decreases since GaN HEMTs have higher source-to-drain voltage drop (V SD ) as compared to the body diode voltage of silicon MOSFETs. Although the power converter presented in [5] uses adaptive deadtime control to achieve a 3% efficiency improvement, due to the unpredictable delay of discrete control, the load-dependent deadtime is still not well controlled. Moreover, considering high switching operation, high dVsw/dt will cause gate ringing problem in switching period. At bottom middle of Fig. 14.1.1, the conventional negative turn-off gate bias and high drain voltage will cause a large electric field between gate and drain, thereby inducing serious trapping effect (bottom left of Fig. 14.1.1). The monolithic GaN driver with adaptive source current (I lCTRL ) does not consider the parasitic effects during turn-off period (bottom right of Fig. 14.1.1) [1].