Daiji Morita
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Daiji Morita has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Ryuji Morita
Department of Applied Physics, Hokkaido University, Sapporo 060-8628, Japan
2 shared publications - Chisako Oda
Mitsubishi Electric Corporation, Tokyo 100-8310, Japan
1 shared publication - Keita Marumoto
Graduate School of Advanced Science and Engineering, Hiroshima University, Higashi-Hiroshima 739-0046, Japan
1 shared publication - Motomichi Yamamoto
Graduate School of Advanced Science and Engineering, Hiroshima University, Higashi-Hiroshima 739-0046, Japan
1 shared publication - Nobuhiro Shinohara
Mitsubishi Electric (Japan), Tokyo, Japan
1 shared publication Nobuyuki Sumi
Industrial Mechatronics Systems Works, Mitsubishi Electric Corporation, Nagoya, Japan
1 shared publication
Latest Publications
- Open Access
- 3 February 2026
- Published by Springer Nature in Progress in Additive Manufacturing
- Vol. 11 (4) , 3395-3408
High-precision thin wall fabrication of aluminum alloys using a wire-laser metal 3D printer with laser power control based on a scaling law
- 3 February 2026
- Published by Springer Nature in Progress in Additive Manufacturing
- Vol. 11 (4) , 3395-3408
Open AccessHigh-precision thin wall fabrication of aluminum alloys using a wire-laser metal 3D printer with laser power control based on a scaling law
- Open Access
- 11 April 2025
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 137 (11-12) , 5983-6002
High-quality and high-resolution thin-wall fabrication of A5183 aluminum alloy using wire-laser metal 3D printer
- 11 April 2025
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 137 (11-12) , 5983-6002
Open AccessHigh-quality and high-resolution thin-wall fabrication of A5183 aluminum alloy using wire-laser metal 3D printer
- Open Access
- 30 April 2024
- Published by MDPI AG in Journal of Manufacturing and Materials Processing
- Vol. 8 (3) , 93
Development of Hot-Wire Laser Additive Manufacturing for Dissimilar Materials of Stainless Steel/Aluminum Alloys
The formation of brittle intermetallic compounds (IMCs) at the interface between dissimilar materials causes considerable problems. In this study, a multi-material additive manufacturing technique that employs a diode laser and the hot-wire method was developed for stainless steel/aluminum alloys. An Al-Mg aluminum alloy filler wire (JIS 5183-WY) was fed on an austenitic stainless-steel plate (JIS SUS304) while varying the laser power and process speed and using paste-type flux and flux-cored wire. The effects of laser power and process speed on phenomena during manufacturing and IMC formation were investigated. Finally, the wall-type multilayer specimens were fabricated under optimized conditions. The suppression of IMC formation to a thickness of less than 2 μm was achieved in the specimens, along with a high interfacial strength of over 120 MPa on average.
- 30 April 2024
- Published by MDPI AG in Journal of Manufacturing and Materials Processing
- Vol. 8 (3) , 93
Open AccessDevelopment of Hot-Wire Laser Additive Manufacturing for Dissimilar Materials of Stainless Steel/Aluminum Alloys
The formation of brittle intermetallic compounds (IMCs) at the interface between dissimilar materials causes considerable problems. In this study, a multi-material additive manufacturing technique that employs a diode laser and the hot-wire method was developed for stainless steel/aluminum alloys. An Al-Mg aluminum alloy filler wire (JIS 5183-WY) was fed on an austenitic stainless-steel plate (JIS SUS304) while varying the laser power and process speed and using paste-type flux and flux-cored wire. The effects of laser power and process speed on phenomena during manufacturing and IMC formation were investigated. Finally, the wall-type multilayer specimens were fabricated under optimized conditions. The suppression of IMC formation to a thickness of less than 2 μm was achieved in the specimens, along with a high interfacial strength of over 120 MPa on average.