Dante Filice
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Dante Filice has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Sylvain Coulombe
McGill University
3 shared publications - Lynn Hein
Catalytic and Plasma Process Engineering, Department of Chemical Engineering, McGill University, Montreal, Quebec H3A 0C5, Canada
1 shared publication Renzo Cecere
1 shared publication- Rosaire Mongrain
Department of Mechanical Engineering, McGill University, Montreal, Canada
1 shared publication Sophie Allard
1 shared publicationSylvain Coulombe
1 shared publication
Latest Publications
- Open Access
- 24 June 2026
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 59 (25) , 255202
Pulsed atmospheric pressure radiofrequency CO 2 and CO 2 + CH 4 discharges: dynamics and effects of carbon particle formation
A combined nanosecond pulsed (nsp) and radiofrequency (RF) source is operated with CO 2 and CO 2 –CH 4 mixtures at atmospheric pressure utilizing a 3-electrode reactor configuration. The effect of carbon particle formation in 60/40 (vol. %) CO 2 /CH 4 mixtures is studied by applying a pulsed excitation sequence of the individual nsp and RF sources while varying the RF pulse lengths. The same excitation sequences are applied to pure CO 2 mixtures to provide baseline conditions with no carbon formation. Analysis of the time domain and frequency domain electrical signals along with high-speed imaging provided a qualitative indication of carbon formation over the duration of each respective RF pulse length. Time-averaged optical emission spectroscopy provided a comparison of plasma species’ intensities for each RF pulse length in both gas mixtures. Longer RF pulse lengths in CO 2 –CH 4 significantly increased the level of carbon formation. High-speed imaging revealed carbon particulate movement toward the electrodes, which was attributed to negative charge accumulation (via plasma electrons) on the carbon particle surface and acceleration toward the positive space charge of the RF sheaths. Frequency domain analysis of the RF electrical signals provided an in-situ temporal indicator of the level of carbon particulate formation in the RF discharge.
- 24 June 2026
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 59 (25) , 255202
Open AccessPulsed atmospheric pressure radiofrequency CO 2 and CO 2 + CH 4 discharges: dynamics and effects of carbon particle formation
A combined nanosecond pulsed (nsp) and radiofrequency (RF) source is operated with CO 2 and CO 2 –CH 4 mixtures at atmospheric pressure utilizing a 3-electrode reactor configuration. The effect of carbon particle formation in 60/40 (vol. %) CO 2 /CH 4 mixtures is studied by applying a pulsed excitation sequence of the individual nsp and RF sources while varying the RF pulse lengths. The same excitation sequences are applied to pure CO 2 mixtures to provide baseline conditions with no carbon formation. Analysis of the time domain and frequency domain electrical signals along with high-speed imaging provided a qualitative indication of carbon formation over the duration of each respective RF pulse length. Time-averaged optical emission spectroscopy provided a comparison of plasma species’ intensities for each RF pulse length in both gas mixtures. Longer RF pulse lengths in CO 2 –CH 4 significantly increased the level of carbon formation. High-speed imaging revealed carbon particulate movement toward the electrodes, which was attributed to negative charge accumulation (via plasma electrons) on the carbon particle surface and acceleration toward the positive space charge of the RF sheaths. Frequency domain analysis of the RF electrical signals provided an in-situ temporal indicator of the level of carbon particulate formation in the RF discharge.
- Open Access
- 1 September 2025
- Published by IOP Publishing in Plasma Sources Science and Technology
- Vol. 34 (9) , 095015
Observation and characterization of discharge mode transition in a three-electrode atmospheric pressure RF plasma system
A new 3-electrode plasma device powered by a combined nanosecond pulsed (nsp) source and a sub-breakdown pulsed radiofrequency (RF) source at atmospheric pressure in a N2/H2 (97.5%/2.5%) mixture is studied. By applying pulsed excitation sequences from both the nsp and RF sources, two different RF discharge modes are obtained depending on the actual participating electrode pair. In the RF dielectric-barrier-discharge (RF-DBD) mode, the discharge forms between the RF metallic pin electrode and the nsp electrode located behind a dielectric surface (exterior to the reactor). In the RF pin-to-pin (RF-PtP) mode, the RF discharge forms between the RF and grounded metallic pin electrodes, both located inside the reactor. The existence of the two RF discharge modes is highly dependent on the RF pulse duration as revealed using high-speed imaging along with a custom electrical measurement technique. It was observed that for longer duration RF pulses, RF-PtP mode is achieved through a transition of RF-DBD into RF-PtP mode (DBD-PtP transition). Electrical characterization revealed higher coupled power percentages for RF-PtP mode (up to 85%) over RF-DBD mode (25%–75%). However, deteriorating impedance matching of the RF-PtP mode decreased the available RF applied power thus yielding similar plasma power deposition as RF-DBD mode. Plasma characterization performed by analysing the emission of the N2 second positive system provided vibrational temperatures up to 3400 K and a thermalization trend of the rotational temperatures as RF pulse duration increased. Mechanisms behind the DBD-PtP transition are proposed under consideration of the obtained data. We attribute the observed discharge dynamics to diffusional forces acting on charged species such as ambipolar diffusional drift and diffusional charge flow.
- 1 September 2025
- Published by IOP Publishing in Plasma Sources Science and Technology
- Vol. 34 (9) , 095015
Open AccessObservation and characterization of discharge mode transition in a three-electrode atmospheric pressure RF plasma system
A new 3-electrode plasma device powered by a combined nanosecond pulsed (nsp) source and a sub-breakdown pulsed radiofrequency (RF) source at atmospheric pressure in a N2/H2 (97.5%/2.5%) mixture is studied. By applying pulsed excitation sequences from both the nsp and RF sources, two different RF discharge modes are obtained depending on the actual participating electrode pair. In the RF dielectric-barrier-discharge (RF-DBD) mode, the discharge forms between the RF metallic pin electrode and the nsp electrode located behind a dielectric surface (exterior to the reactor). In the RF pin-to-pin (RF-PtP) mode, the RF discharge forms between the RF and grounded metallic pin electrodes, both located inside the reactor. The existence of the two RF discharge modes is highly dependent on the RF pulse duration as revealed using high-speed imaging along with a custom electrical measurement technique. It was observed that for longer duration RF pulses, RF-PtP mode is achieved through a transition of RF-DBD into RF-PtP mode (DBD-PtP transition). Electrical characterization revealed higher coupled power percentages for RF-PtP mode (up to 85%) over RF-DBD mode (25%–75%). However, deteriorating impedance matching of the RF-PtP mode decreased the available RF applied power thus yielding similar plasma power deposition as RF-DBD mode. Plasma characterization performed by analysing the emission of the N2 second positive system provided vibrational temperatures up to 3400 K and a thermalization trend of the rotational temperatures as RF pulse duration increased. Mechanisms behind the DBD-PtP transition are proposed under consideration of the obtained data. We attribute the observed discharge dynamics to diffusional forces acting on charged species such as ambipolar diffusional drift and diffusional charge flow.
- Open Access
- 1 July 2025
- Published by Elsevier in Journal of Drug Delivery Science and Technology
- Vol. 112
Controlled drug release from a polymer-free multi-walled carbon nanotube-based coating
- 1 July 2025
- Published by Elsevier in Journal of Drug Delivery Science and Technology
- Vol. 112
Open AccessControlled drug release from a polymer-free multi-walled carbon nanotube-based coating
- Open Access
- 1 May 2024
- Published by IOP Publishing in Plasma Sources Science and Technology
- Vol. 33 (5) , 055011
Combined ns pulsed-RF excitation and impedance matching considerations for the production of moderate E/n atmospheric pressure discharges for gas conversion
Sub-breakdown radiofrequency (RF) discharges enabled by a nanosecond (ns) pulse ignition source are studied at atmospheric pressure in a range of gas mixtures from completely inert (in Ar) to completely reactive (in CO2). An electrical characterisation of the continuous wave (CW) RF discharge (13.56 MHz) is performed to determine plasma impedance and plasma power dissipation. Two different measurement methods to electrically characterize the system are described and compared. One method uses in-situ measurements of discharge parameters (voltage, current and the phase angle), and the other method performs ex-situ measurements of the load circuit using a vector network analyser. It was found that RF plasma power deposition depended on the applied RF power as well as the gas mixture composition. Using the in-situ voltage, current and phase angle measurements, plasma power deposition was calculated to be as much as 85% and 76% of the applied RF power for the pure Ar and pure CO2 cases, respectively. A preliminary qualitative assessment of the plasma composition was performed by optical emission spectroscopy, and CO2 conversion by mass spectrometry. CO2 to CO conversions of 11.2% and 5.5% in a 20:80 (CO2:Ar) mixture and in 100% CO2, respectively, were observed. This study demonstrates a RF plasma source for gas conversion applications at atmospheric pressure in a completely reactive gas.
- 1 May 2024
- Published by IOP Publishing in Plasma Sources Science and Technology
- Vol. 33 (5) , 055011
Open AccessCombined ns pulsed-RF excitation and impedance matching considerations for the production of moderate E/n atmospheric pressure discharges for gas conversion
Sub-breakdown radiofrequency (RF) discharges enabled by a nanosecond (ns) pulse ignition source are studied at atmospheric pressure in a range of gas mixtures from completely inert (in Ar) to completely reactive (in CO2). An electrical characterisation of the continuous wave (CW) RF discharge (13.56 MHz) is performed to determine plasma impedance and plasma power dissipation. Two different measurement methods to electrically characterize the system are described and compared. One method uses in-situ measurements of discharge parameters (voltage, current and the phase angle), and the other method performs ex-situ measurements of the load circuit using a vector network analyser. It was found that RF plasma power deposition depended on the applied RF power as well as the gas mixture composition. Using the in-situ voltage, current and phase angle measurements, plasma power deposition was calculated to be as much as 85% and 76% of the applied RF power for the pure Ar and pure CO2 cases, respectively. A preliminary qualitative assessment of the plasma composition was performed by optical emission spectroscopy, and CO2 conversion by mass spectrometry. CO2 to CO conversions of 11.2% and 5.5% in a 20:80 (CO2:Ar) mixture and in 100% CO2, respectively, were observed. This study demonstrates a RF plasma source for gas conversion applications at atmospheric pressure in a completely reactive gas.