ESEva Schubert

Eva Schubert

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Eva Schubert has a total of 36 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Spectroscopic ellipsometry determined dielectric function from 0.74 to 9.25 eV and band-to-band transitions in zirconia thin films fabricated by electron-beam-assisted deposition

    by Ufuk Kilic, Raymond Smith, Matthew Hilfiker, Shawn Wimer, Eva Schubert, Mathias Schubert

    Zirconia (ZrO2) thin films were fabricated using an ultra-high-vacuum electron-beam physical vapor deposition technique. Spectroscopic ellipsometry (SE) data from multiple samples with different thicknesses were acquired over a broad photon-energy range of 0.74–9.25 eV to determine the frequency-dependent complex dielectric function of ZrO2 thin films. Atomic force microscopy (AFM) analysis confirms the formation of highly uniform films with an average height variation below 2 nm across the scanned areas. In the SE-based optical analysis, a five-layer model consisting of the substrate, native oxide, ZrO2 thin film, surface roughness layer, and ambient was employed within a multi-sample analysis framework. The surface roughness layer was modeled using a 50:50 effective medium approximation of the film and ambient, yielding roughness thicknesses consistent with those obtained from AFM measurements. By parameterizing the intrinsic dielectric response using a set of oscillators, a critical-point model dielectric-function analysis was applied to identify band-to-band transition parameters. These results provide a comprehensive parameterization of the dielectric function of electron-beam-deposited ZrO2 thin films and establish a robust ellipsometry-based framework for correlating thin-film structure and optical properties in ultra-wide-bandgap oxide materials.

  • Open Access

    Evolution of the near-infrared-to-ultraviolet model dielectric function of InAs from room temperature to 250 °C determined by spectroscopic ellipsometry

    by Preston R. Sorensen, Ufuk Kilic, Yousra Traouli, Rafał Korlacki, Eva Schubert, Mathias Schubert

    We present a model dielectric function composed of critical point functions in order to parameterize the temperature and wavelength dependencies of the dielectric function of InAs. This model is based on Adachi’s critical point model, with simple wavelength-dependent analytical functions whose parameters change linearly with temperature. The calculated dielectric function at room temperature is in excellent agreement with previously published data. We apply this model in the spectral range of 0.7–5 eV and in the temperature range of room temperature to 250°C with in situ spectroscopic ellipsometry measurements on an InAs substrate. Spectroscopic measurements were performed continuously while slowly ramping sample temperature in a stepwise manner in the controlled ambient environment of an atomic layer deposition system. We find that our model matches excellently with all experimental data with deviations less than 2% in pseudoepsilon. Our model permits smooth interpolation of the dielectric function of InAs for any intermediate temperature in the range studied and therefore can be used to monitor temperature, for example, during thin film deposition processes by in situ spectroscopic ellipsometry. We propose that this model can be applied to other semiconductors as well as wider temperature ranges.

  • Open Access

    Dielectric function, band-to-band transitions, and exciton properties of bulk single-crystal In2O3 from room temperature to 600 °C determined by in situ spectroscopic ellipsometry

    by Sema Guvenc Kilic, Ufuk Kilic, Matthew Hilfiker, Eva Schubert, Zbigniew Galazka, Mathias Schubert

    We investigate the temperature-dependent complex dielectric function of bulk single-crystal In2O3 over the spectral range of 1–6 eV and temperatures from room temperature to 600 °C under high-vacuum conditions using in situ spectroscopic ellipsometry. The dielectric function was modeled using wavelength-by-wavelength and critical-point model dielectric function analyses. The dielectric function exhibits pronounced alterations with increasing temperature, attributed to thermally induced changes in the band structure and carrier dynamics. We identify direct and indirect interband transitions and excitonic contributions associated with the direct bandgap near the onset of absorption. At elevated temperatures, features in the dielectric function due to indirect transitions emerge below the direct bandgap energy, which shift toward shorter photon energies with increasing temperature. Combining our results with low-temperature data from previous reports, both observed shifts of the direct and indirect transitions can be seamlessly explained with the Bose–Einstein model. The direct transition is coupled less strong to the phonon bath (average temperature θB=512 K), leading to a smaller high-temperature slope (γ=−0.2 meV/K) than for the indirect transition (θB=360 K, γ=−1.3 meV/K). The exciton contributions diminish toward higher temperatures reflected by the decrease in amplitude and increase in broadening model parameters. Our parameter set can be used to calculate the model dielectric function In2O3 at elevated temperatures.

  • Open Access

    Electronic band structure, band-to-band transitions, and anisotropic dielectric functions of orthorhombic NdGaO3

    by Yousra Traouli, Ufuk Kilic, Rafał Korlacki, Matthew Hilfiker, Alyssa Mock, Eva Schubert, Mathias Schubert

    A set of ultrawide bandgap single-crystal NdGaO3 samples cut with crystallographic surface orientations (001), (101), and (110) are investigated by using generalized spectroscopic ellipsometry. We report the complex anisotropic dielectric functions in the spectral range from 0.73 to 9.0 eV, for polarization along directions a, b, and c of the orthorhombic unit cell. A Kramers–Kronig consistent parameterized model was utilized to identify critical point structures and their association with band-to-band transitions, and the results from density functional theory (DFT) calculations for the electronic band structure of NdGaO3 are compared. A Cauchy parameter analysis for the three refractive indices is performed in the below bandgap spectral range. Dielectric functions along lattice directions a, b, and c and their respective bandgap energy values are very similar. Below the bandgap energy, the refractive index differences for directions a and b are very small (0.34% on average) while index differences with direction c (approximately 1.25%) lead to effective positive uniaxial optical properties (nc>na≈nb) toward the phonon modes spectral range. Our ellipsometry analysis determines the lowest band-to-band transitions of NdGaO3 to occur at Ea=6.46(6)eV, Eb=6.29(5)eV, and Ec=6.77(7)eV, i.e., Ec>Ea>Eb, while our DFT calculations predict the first transition to be lowest along the a axis. We discuss our findings in light of previous reports and present all parameters of our theoretical and experimental analyses.


  • Self-induced nonreciprocity from asymmetric photonic topological insulators

    by Sema Guvenc Kilic, Ufuk Kilic, Mathias Schubert, Eva Schubert, Christos Argyropoulos


  • In-cycle evolution of thickness and roughness parameters during oxygen plasma enhanced ZnO atomic layer deposition using in situ spectroscopic ellipsometry

    by Yousra Traouli, Ufuk Kilic, Sema G. Kilic, Matthew Hilfiker, Daniel Schmidt, Stefan Schoeche, Eva Schubert, Mathias Schubert

    We investigate the time evolution of ZnO thin film growth in oxygen plasma-enhanced atomic layer deposition using in situ spectroscopic ellipsometry. The recently proposed dynamic-dual-box-model approach [Kilic et al., Sci. Rep. 10, 10392 (2020)] is used to analyze the spectroscopic data post-growth. With the help of this model, we explore the in-cycle surface modifications and reveal the repetitive layer-by-layer growth and surface roughness modification mechanisms during the ZnO ultrathin film deposition. The in situ complex-valued dielectric function of the amorphous ZnO thin film is also determined from the model analysis for photon energies of 1.7–4 eV. The dielectric function is analyzed using a critical point model approach providing parameters for bandgap energy, amplitude, and broadening in addition to the index of refraction and extinction coefficient. The dynamic-dual-box-model analysis reveals the initial nucleation phase where the surface roughness changes due to nucleation and island growth prior to film coalescence, which then lead to the surface conformal layer-by-layer growth with constant surface roughness. The thickness evolution is resolved with Angstrom-scale resolution vs time. We propose this method for fast development of growth recipes from real-time in situ data analysis. We also present and discuss results from x-ray diffraction, x-ray photoelectron spectroscopy, and atomic force microscopy to examine crystallographic, chemical, and morphological characteristics of the ZnO film.


  • Open Access

    Controlling the broadband enhanced light chirality with L-shaped dielectric metamaterials

    by Ufuk Kilic, Matthew Hilfiker, Shawn Wimer, Alexander Ruder, Eva Schubert, Mathias Schubert, Christos Argyropoulos

    The inherently weak chiroptical responses of natural materials limit their usage for controlling and enhancing chiral light-matter interactions. Recently, several nanostructures with subwavelength scale dimensions were demonstrated, mainly due to the advent of nanofabrication technologies, as a potential alternative to efficiently enhance chirality. However, the intrinsic lossy nature of metals and the inherent narrowband response of dielectric planar thin films or metasurface structures pose severe limitations toward the practical realization of broadband and tailorable chiral systems. Here, we tackle these problems by designing all-dielectric silicon-based L-shaped optical metamaterials based on tilted nanopillars that exhibit broadband and enhanced chiroptical response in transmission operation. We use an emerging bottom-up fabrication approach, named glancing angle deposition, to assemble these dielectric metamaterials on a wafer scale. The reported strong chirality and optical anisotropic properties are controllable in terms of both amplitude and operating frequency by simply varying the shape and dimensions of the nanopillars. The presented nanostructures can be used in a plethora of emerging nanophotonic applications, such as chiral sensors, polarization filters, and spin-locked nanowaveguides.


  • Vector magneto-optical generalized ellipsometry for sculptured thin films

    by Daniel Schmidt, Chad Briley, Eva Schubert, Mathias Schubert

    Vector magneto-optical generalized ellipsometry is employed for the determination of the three-dimensional magnetization properties of magnetized thin solid as well as slanted columnar thin film samples. The permalloy thin films were probed by means of Mueller matrix ellipsometry at room-temperature while an external magnetic field was rotated step-wise within each plane of a three-dimensional Cartesian coordinate system (spatial hysteresis loops). Model analysis of the magneto-optical coupling parameter (proportional to the magnetization) confirms the expected uniaxial magnetization shape of the thin solid film and reveals the three-dimensional magneto-optic anisotropy of the nanostructured thin film.


  • Optically pumped InGaN/GaN lasers with wet-etched facets

    by D. A. Stocker, E. F. Schubert, J. M. Redwing


  • New possibilities for joining by using high power diode lasers

    by E. Schubert, I. Zerner, G. Sepold

    High power diode lasers with an output power above 1 kW are available today. These systems offer a low beam quality at a short wavelength combined with low price and operating costs. Joining of aluminium to steel of thin sheets becomes possible using high power laser systems like Nd: YAG or high power diode laser. By the irradiation of the laser beam the aluminium sheet can be molten and the liquid metal can wet the steel sheet. Using high temperature gradients the growing of critical intermetallic phases can be controlled. Joints with a high tensile strength and a formability similar to laser welded aluminium can be achieved. The use of high power diode lasers for joining aluminium to steel is a combination with several advantages. The use of a diode laser instead of a Nd:YAG-laser can reduce costs and the short wavelength can lead to a better process efficiency. On the other hand the low beam quality does not effect the process. An increase of the beam quality in future will result in increased working distances to protect the laser optics from process emissions. Therefore, further investigations with the combination of high power diode laser and joining of aluminium to steel will be done in order to apply this new technology in industrial manufacturing.