Liguang Qin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Liguang Qin has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
Bo Zhang
3 shared publications- Aiguo Zhou
School of Materials Science and Engineering Henan Polytechnic University Jiaozuo China
2 shared publications - Chang Guo
School of Mechanical Engineering and Rail Transit, Changzhou University, Changzhou, Jiangsu, China
2 shared publications Linhao Xin
2 shared publicationsShangqi Sun
Changzhou University
2 shared publicationsShaomin Zhang
2 shared publications
Latest Publications
- 15 December 2024
- Published by Elsevier in Chemical Engineering Journal
- Vol. 503
Achieving layered deposition of lithium by uniform Li-ion flux distribution in grids
- 15 December 2024
- Published by Elsevier in Chemical Engineering Journal
- Vol. 503
Achieving layered deposition of lithium by uniform Li-ion flux distribution in grids
- Open Access
- 4 September 2024
- Published by Wiley
Uniform Li-ion flux distribution in grids to compartmentalize Li growth for high safety lithium metal anode
Lithium metal is regarded as the most promising anode for next generation high-energy-density batteries. However, it still suffers from the problems associated with the uncontrollable dendrite growth and infinite volume expansion. Herein, a flexible and insulative polyethylene mesh (PM) has been used to partition the electrochemical reaction area, enhancing the uniformity of Li deposition/dissociation behaviors within localized regions. On the one hand, the insulating mesh can restrict the transport direction of Li+, mitigating “hotspots” induced by Li-ions agglomeration and thereby preventing dendrites formation. On the other hand, after Li deposited in segmented areas, the failure within a single mesh will not affect the performance of the entire electrode, thus improving the long-term stability of the electrode. Nevertheless, the mesh number as well as the thickness of the PM have significant influence on Li deposition/dissolution behaviors. As a result, the PM-40 with a thickness of 0.1 mm demonstrated the best regulation effects: in Cu||Li half-type cell, the PM-40 exhibited excellent cycling stability with an average Coulombic efficiency (CE) of 97.3%. When paired with LiFePO4 cathodes, the PM-40 demonstrated superior long-term cycling stability over 700 cycles with 98.87% capacity retention at 1C. This work effectively improves the uniformity of Li plating/stripping behaviors and electrochemical performance through a highly cost-effective method. Meanwhile, this work paves the way for realizing high-performance anode-free lithium metal batteries (LMBs) through the strategy of confined Li reaction.
- 4 September 2024
- Published by Wiley
Open AccessUniform Li-ion flux distribution in grids to compartmentalize Li growth for high safety lithium metal anode
Lithium metal is regarded as the most promising anode for next generation high-energy-density batteries. However, it still suffers from the problems associated with the uncontrollable dendrite growth and infinite volume expansion. Herein, a flexible and insulative polyethylene mesh (PM) has been used to partition the electrochemical reaction area, enhancing the uniformity of Li deposition/dissociation behaviors within localized regions. On the one hand, the insulating mesh can restrict the transport direction of Li+, mitigating “hotspots” induced by Li-ions agglomeration and thereby preventing dendrites formation. On the other hand, after Li deposited in segmented areas, the failure within a single mesh will not affect the performance of the entire electrode, thus improving the long-term stability of the electrode. Nevertheless, the mesh number as well as the thickness of the PM have significant influence on Li deposition/dissolution behaviors. As a result, the PM-40 with a thickness of 0.1 mm demonstrated the best regulation effects: in Cu||Li half-type cell, the PM-40 exhibited excellent cycling stability with an average Coulombic efficiency (CE) of 97.3%. When paired with LiFePO4 cathodes, the PM-40 demonstrated superior long-term cycling stability over 700 cycles with 98.87% capacity retention at 1C. This work effectively improves the uniformity of Li plating/stripping behaviors and electrochemical performance through a highly cost-effective method. Meanwhile, this work paves the way for realizing high-performance anode-free lithium metal batteries (LMBs) through the strategy of confined Li reaction.
- 30 April 2024
- Published by Wiley in Energy Technology
- Vol. 12 (7)
Influence of Interfacial Energy on Li Nucleation Behaviors during Electrodeposition Process
It is generally believed that the introduction of the 3D structure in Cu current collector (CuCC) is beneficial for the uniform deposition of Li due to the reduced local current density and mitigatory reaction rate. However, the influence of the microstructure change in CuCC on the nucleation behaviors of Li through mechanical treatment has been ignored. Hence, microindent is used to prepare 3D structure on the surface of CuCC, the structure evolution during microindentation as well as its impact on Li nucleation behaviors are investigated. It is found that the increased specific surface area results in decreased current density and reduced nucleation driving force. The crystal misorientation beneath the indent leads to the increased surface energy and inhomogeneous nucleation of Li. Thus, the indented CuCC (Ind CuCC) exhibits higher nucleation overpotential and slower electron transfer rate. This manuscript provides a new perspective to the study of the impact of the microstructure of current collector on the nucleation behaviors of Li.
- 30 April 2024
- Published by Wiley in Energy Technology
- Vol. 12 (7)
Influence of Interfacial Energy on Li Nucleation Behaviors during Electrodeposition Process
It is generally believed that the introduction of the 3D structure in Cu current collector (CuCC) is beneficial for the uniform deposition of Li due to the reduced local current density and mitigatory reaction rate. However, the influence of the microstructure change in CuCC on the nucleation behaviors of Li through mechanical treatment has been ignored. Hence, microindent is used to prepare 3D structure on the surface of CuCC, the structure evolution during microindentation as well as its impact on Li nucleation behaviors are investigated. It is found that the increased specific surface area results in decreased current density and reduced nucleation driving force. The crystal misorientation beneath the indent leads to the increased surface energy and inhomogeneous nucleation of Li. Thus, the indented CuCC (Ind CuCC) exhibits higher nucleation overpotential and slower electron transfer rate. This manuscript provides a new perspective to the study of the impact of the microstructure of current collector on the nucleation behaviors of Li.