SLShen Luo

Shen Luo

*This is an algorithmically generated author record based on publicly available information.

Shen Luo has a total of 12 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Experimental Investigation on the Fracture Behavior of PET-Modified Engineered High-Ductility Concrete: Effects of PET Powder and Precursor Composition

    by Fei Meng, Shen Luo, Jingxian Sun, Cheng Zhang, Leilei Xu, Liqun Zhang, Fumin Qing, Junfeng Zeng, Ruihao Luo, Yongchang Guo

    The utilization of polyethylene terephthalate (PET) powder as aggregate in the development of environmentally friendly high-ductility composites (P-EHDC) offers a promising pathway for advancing sustainable and high-performance concrete materials. Despite its potential, the fracture behavior of P-EHDC—particularly under the influence of alkali-activated precursors—remains insufficiently explored. In this study, the fracture performance of P-EHDC was evaluated by varying the precursor composition ratios (GGBS:FA = 4:6, 3:7, and 2:8) and PET powder replacement ratios (0%, 15%, 30%, and 45% by volume). Fracture modes, Mode I fracture energy (GF), and crack propagation behavior were analyzed using the J-integral method. All specimens exhibited ductile fracture characteristics, a clear contrast to the brittle failure observed in conventional concrete. The replacement of 15 vol% PET powder significantly increased GF in precursor systems with higher GGBS content (4:6 and 3:7), and 30 vol% was more effective in fly ash-rich systems (2:8). The J-integral method, which offers broader applicability compared to conventional methods such as the double-K fracture model, provided a more comprehensive understanding of the fracture behavior. The results showed that PET powder reduced the matrix fracture toughness, promoted matrix cracking, and weakened the fiber-bridging effect, leading to enhanced energy absorption via fiber pull-out. At low PET powder replacement ratios (e.g., 15 vol%), the cracking threshold of the matrix was not significantly reduced, while more fibers engaged during the crack instability stage to absorb fracture energy through pull-out. This behavior highlights the synergistic toughening effect between PET powder and fibers in the P-EHDC system. The effect became more pronounced when the PET content was below 45 vol% and the precursor matrix contained a higher proportion of GGBS, leading to enhanced ductility. This study introduces a novel approach to fracture behavior analysis in PET-modified alkali-activated composites and provides theoretical support for the toughening design of high-performance, low-carbon concrete materials.


  • Open Access

    Compressive and Tensile Behavior of High-Ductility Alkali-Activated Composites with Polyethylene Terephthalate Powder

    by Fei Meng, Shen Luo, Jingxian Sun, Cheng Zhang, Leilei Xu, Yankun Du, Junfeng Zeng, Yongchang Guo

    Researchers have been engaged in the study of high-ductility concrete (HDC) due to its excellent ductility and cracking control ability. This study combines the concepts of HDC and alkali-activated composites (AAC) to develop high-ductility alkali-activated composites (HDAAC) using polyethylene terephthalate (PET) powder. Experimental investigations were conducted to assess the compressive and tensile properties of HDAAC, focusing on the impact of varying PET powder content (0%, 15%, 30%, and 45%) and fly ash/slag ratios (FA/GGBS, 6:4, 7:3, and 8:2). The results indicated that the compressive strength of HDAAC ranged from approximately 30 MPa to about 100 MPa, with the specimens maintaining good integrity after axial compression failure due to the bridging action of PE fibers. The replacement of quartz powder (QP) with PET powder slightly decreased the compressive strength and elastic modulus of HDAAC, albeit mitigating its brittleness under compression. An increase in GGBS content enhanced the compressive strength and elastic modulus of HDAAC due to the increased formation of the C-A-S-H reaction products, leading to reduced porosity and a denser microstructure. Under axial tension, HDAAC exhibited typical multiple-cracking behavior with significant pseudo-strain hardening. Increases in the PET content and FA/GGBS ratio resulted in finer cracks, indicating excellent crack control and deformation capabilities. The initial cracking strength, tensile strength, and ultimate tensile strain ranged from 3.0 MPa to 4.6 MPa, 4.2 MPa to 8.2 MPa, and 4.1% to 7.2%, respectively. Despite a decrease in the initial cracking strength and tensile strength with higher PET content, the ultimate tensile strain of HDAAC slightly increased. Observations under a scanning electron microscope revealed a distinct interfacial transition zone near the PET powder, leading to poor bonding with the alkali-activated matrix. In contrast, QP dissolved on the surface in highly alkaline environments, forming better interface properties. These variations in interface properties can be used to interpret the variations in the mechanical performance of HDAAC.