JXJiangtao Xia

Jiangtao Xia

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Jiangtao Xia has a total of 15 co-authors. Here are the top co-authors by number of shared publications:

  • Bin Liu

    State Key Laboratory of Powder Metallurgy, Central South University, Changsha, China

    1 shared publication
  • Chengwei Cai

    Suzhou Institute of Industrial Technology, Suzhou, China

    1 shared publication
  • Hui Feng

    College of Mechanical and Vehicle Engineering, Hunan University, Changsha, CHINA

    1 shared publication
  • Hui Xiang

    School of Civil and Architectural Engineering, Hainan University, Haikou 570228, China

    1 shared publication
  • Jia Li

    College of Mechanical and Vehicle Engineering, Hunan University, Changsha, CHINA

    1 shared publication
  • Jia Li

    State Key Laboratory of Advanced Design and Manufacturing Technology for Vehicle, College of Mechanical and Vehicle Engineering, Hunan University, Changsha 410082, China

    1 shared publication

Latest Publications

  • Anomalous temperature dependence of shock response in a refractory multi-principal element alloy: from shear localization to homogeneous plasticity

    by Jiangtao Xia, Jing Peng, Jia Li, Qihong Fang, Hui Feng

    The shock response and underlying deformation mechanisms of a polycrystalline MoNbTa refractory multi-principal element alloy (RMPEA) are investigated using large-scale molecular dynamics simulations. The simulations systematically explore the effects of initial temperature on the dynamic mechanical response and microstructural evolution. The results revealed that within the initial temperature range of 5–1200 K, the shock behavior of MoNbTa RMPEA exhibited a weak temperature dependence. The longitudinal and transverse stresses only slightly decrease with the increase of temperature, while the waveform changes of stress, particle velocity and density remain almost unchanged, demonstrating the high-temperature impact stability. The analysis of the stress state indicates that volumetric strain and distortion strain are separated. Hydrostatic pressure maintains a continuous and stably propagating impact front, while von Mises stress maps the persistent non-uniform plastic zone behind the front, indicating that energy is widely dissipated through defect-induced plasticity. In addition, the shock damage is mainly manifested in the diffusion of the initial grain boundary dislocation network, the formation of dislocations within the grains, and amorphous transformation. Some damaged structures can recover dynamically after the shock. Compared with pure Nb and NbMo alloys, MoNbTa RMPEA exhibits suppressed amorphization, reduced grain boundary degradation, and superior resistance to catastrophic shear localization under extreme shock loading. These findings provide atomic‐scale insight into the coupled effects of temperature and high‐strain‐rate deformation in RMPEAs.

  • Irradiation Hardening and Creep Modeling of High-Entropy Alloy at High Temperature and Dose

    by Yulian Liu, Yang Chen, Jia Li, Bin Liu, Ruiqian Zhang, Jiangtao Xia, Qihong Fang


  • Open Access

    Study on Frost Heave and Thaw Settlement Characteristics of Sanya Estuary Channel Soil Layer

    by Xiuwen Wu, Jun Hu, Junxin Shi, Hui Xiang, Jiangtao Xia

    In order to explore the frost heave and thaw settlement characteristics of soil layers in the Sanya Estuary Channel Project, the frost heave rate and thaw settlement coefficient of gravel sand, fine sand, silty clay, and clay are obtained. The most unfavorable soil layers are then compared and analyzed. The variation law of frost heave and thaw settlement performance of the most unfavorable soil layer under different water content is studied. The results are as follows: (1) The freezing stage of the passage through the typical soil layer is divided into four stages: frost shrinkage, rapid frost heave, slow frost heave, and frost heave stability. The melting stage is divided into three stages: slow thaw settlement, rapid thaw settlement, and thaw settlement stability. (2) The most unfavorable soil layer in the typical soil layer of the Sanya Estuary Channel Project is silty clay, with a frost heave rate and thaw settlement coefficient of 4.51% and 5.88% at −28 °C. (3) The frost heave and thaw settlement performance of the most unfavorable soil layer is linearly related to water content. The larger the water content, the greater the frost heave rate and thaw settlement coefficient, and the more prone to damage.