Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Marko Stojanović has a total of 23 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Non-Destructive Characterization of Cultural Heritage Materials Using a Modified Acoustic Resonance Approach

    by Filip Pantelić, Miloš Radomir Vasić, Marko Stojanović, Anja Terzić, Bojan Miljević, Snežana Vučetić

    This study explores non-destructive techniques for characterizing the mechanical properties of materials pertinent to cultural heritage, emphasizing the preservation of sample integrity. A modified acoustic resonance method (MARM), utilizing a two-microphone configuration, is introduced for the simultaneous, fully non-contact determination of dynamic elastic modulus and damping (loss factor). The method is validated through comparison with the impulse excitation technique (IET) and ultrasonic pulse velocity testing (UT). The approach is applied to two material categories exhibiting contrasting porosities: dense natural stone and highly porous unfired clay. Results demonstrate strong concordance among all methods for stone, confirming the reliability of non-destructive techniques for homogeneous materials. Conversely, unfired clay displays greater variability attributable to its heterogeneous and porous nature, alongside increased damping. This investigation reveals that conventional modulus–strength correlations are not directly applicable to unfired clay. To address this, a simplified strength estimation model incorporating the estimated elastic modulus and porosity is proposed. The model achieves improved alignment with experimental data and delineates applicability boundaries for porous materials. The presented framework facilitates consistent, non-destructive evaluation of mechanical properties, with notable implications for the assessment and preservation of cultural heritage materials.

  • Influence of crumb rubber and water-cement ratio on the properties of fresh and hardened concrete

    by Marko Stojanović, Anja Terzić, Ksenija Janković, Dragan Bojović, Željko Flajs

    This paper investigates the influence of crumb rubber obtained from recycled waste tires on the properties of fresh and hardened concrete. Crumb rubber was used as a partial volumetric replacement of fine aggregate in proportions of 2.5% and 5.0%. The experimental program included testing of fresh concrete properties (workability, density, and air content) as well as hardened concrete properties (density, compressive strength, and water permeability). Tests were conducted for two water-cement ratios (w/c = 0.55 and w/c = 0.45). The results showed that the addition of crumb rubber reduces concrete density and compressive strength while increasing the air content in fresh concrete mixtures. An increase in the depth of water penetration was also observed in mixtures containing higher percentages of crumb rubber, particularly at higher water-cement ratios. However, the use of a lower water-cement ratio mitigates the negative effects of rubber addition due to the formation of a denser cement matrix microstructure. The obtained results indicate that crumb rubber can be used as an alternative material in concrete production, provided that the mixture composition and replacement percentage are carefully defined.

  • GRAPHENE OXIDE-MODIFIED CONCRETE

    by Ksenija Janković, Anja Terzić, Marko Stojanović, Dragan Bojović

    Given that concrete is currently the most widely used building material, its strength and durability are essential qualities. Recent advances in new nanoscale fibers like as carbon nanotubes and graphene oxide have improved the performance of concrete. Graphene oxide (GO) is a two-dimensional planar sheet of compressed carbon atoms in a honeycomb configuration with thickness 0.335 nm. GO is a promising nanomaterial due to its unique properties, namely, it has received international attention for its outstanding mechanical, optical, and thermal properties. In addition to regulating the secondary hydration mechanism, adding GO to concrete improves its mechanical performance, durability, self-healing, and other multifunctional characteristics. This study presents an investigation of the properties of concrete with GO addition. Four different concrete mix designs were prepared. GO was added in quantities of 0.01, 0.02, 0.03, and 0.06 %. Hydration routes were analyzed by differential thermal analysis. Mechanical strengths were tracked in duration od 28 days and frost resistance with deicing salts during 56 cycles.

  • COMPARATIVE ANALYSIS OF CONCRETE WITH PORTLAND COMPOSITE CEMENTS WITH REDUCED CLINKER CONTENT

    by Sanja Ćorić, Marina Škondrić, Aleksandar Radević, Aleksandar Savić, Marko Stojanović

    The paper presents the results of experimental testing of concrete mixtures made with Portland composite cements with reduced clinker content (PC 50M). The aim of the study was to examine the justification for using this type of cement (defined by the document SDO 15 001:2021) in concretes commonly used in construction practice. The compressive strength reached values ranging from 48.0 to 55.8 MPa, while all other parameters: splitting tensile strength, water impermeability, frost resistance, and thermogravimetric analysis, also showed very good performance. The results support the use of this type of cement in the construction industry.

  • THE INFLUENCE OF CRUMB RUBBER ON THE FREEZE-THAW RESISTANCE OF CONCRETE

    by Marko Stojanović, Ksenija Janković, Dragan Bojović, Anja Terzić, Slobodan Šupić

    Waste tires are a persistent challenge in waste management. To reduce environmental impact and utilize this material more effectively, its use in concrete mixtures has been studied. This research aims to incorporate waste materials into concrete production while ensuring acceptable performance. The study presents results where fine aggregate was partially replaced with crumb rubber (2.5% and 5% by volume). All mixtures were designed with a w/c= 0.55 and compared with a control and a mixture with a chemical air-entraining admixture. Fresh concrete properties were monitored after 10, 30, and 60 minutes. After 60 minutes, rubber-modified mixtures showed increased air content and decreased density. The hardened concrete with rubber had lower compressive strength but better resistance after 200 freeze-thaw cycles compared to the control.

  • Open Access

    Investigation of the mechanical properties of concrete incorporating recycled rubber particles

    by Marko S. Stojanović, Slobodan Supic, Ksenija Jankovic, Dragan Bojovic, Anja Terzic, Mirjana Malesev

    Quantity of waste rubber generated by automobile tires is growing, posing an environmental threat. Rubber tire recycling was studied for usage in asphalt and waterproofing systems during past few decades. Globally, concrete is the most widely used building material. About 7% of CO2 emissions come from the cement production. The purpose of this research is to assess if using waste rubber and Portland cement together in composite material for structural applications is feasible. Waste tires (shredded to 0/1 mm) were used as fine aggregate replacement (in 2.5 and 7.5 %), together with PC and natural stone. An investigation of properties in fresh (slump test, bulk density, air content) and hardened state (bulk density, compressive strength) was performed on the rubberized concrete. The compressive strength decreased by increasing the rubber content for all w/c ratios (0.55-0.4). The addition of fine-sized rubber did not cause a retardation in cement hydration mechanism. According to the obtained compressive strengths, all designed rubberized concretes belong to a group of structural concretes.


  • Open Access

    Assessment of construction and demolition waste application for improving frost resistance in masonry clay units

    by Miloš R. Vasić, Anja Terzic, Marko Stojanovic, Milos Vorkapic, Dragan Bojovic

    The main objective of the research was to estimate the feasibility of construction and demolition waste (CDW) application in the production of frost-resistant masonry clay elements. After being formed into hollow masonry blocks and bricks, the experimental samples were dried and fired. Chemical, granulometric, mineralogical, differential-thermal, and thermogravimetric analyses were used for characterizing the materials. Drying sensitivity and plasticity were assessed using the Bigot and Pfefferkorn tests. Linear shrinkage and compressive strength were determined on green and fired ceramic samples. Frost resistance was tested in accordance with EN 772-22 and ASTM C1167-22. The mercury intrusion porosimeter and RapidAir 457 were used in the evaluation of the pore size distribution. Clay elements fired at lower temperatures proved more frost-resistant. Waste-based elements exhibited improved frost resistance compared to standard bricks and hollow blocks. The compressive strength of the waste-added building products was reduced, but it still exceeded the standard strength values for their application in load-bearing walls.


  • BASIC ASPECTS OF ASSESSMENT AND VERIFICATION OF CONSTANCY OF PERFORMANCE OF CONCRETE

    by Biljana Ilić, Dragan Bojović, Lana Antić Aranđelović, Marko Stojanović, Ksenija Janković

  • Open Access

    Possibility of using bottom ash in precast concrete products

    by Stjepan Lakusic, Ksenija Janković, Dragan Bojović, Ljiljana Lončar, Marko Stojanović, Lana Antić


  • Open Access

    The influence of tailings and cement type on durability properties of self-compacting concrete

    by Ksenija Janković, Nenad Šušić, Marko Stojanović, Dragan Bojović, Ljiljana Lončar

    Da bi se ispitala razlika u kemijskom sastavu i mogućnost primjene jalovine iz rudnika u proizvodnji žbuke i betona uzeti su uzorci s deponija i direktno iz proizvodnje. Nijedan uzorak nije pokazao pucolansku aktivnost. Iz tog razloga,...