Julián Acevedo
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Julián Acevedo has a total of 4 co-authors. Here are the top co-authors by number of shared publications:
- Diana López
Química de Recursos Energéticos y Medio Ambiente, Instituto de Química, Facultad de Ciencias Exactas y Naturales, Universidad de Antioquia, calle 70 No. 52-21, Medellín 050010, Colombia
2 shared publications - Jennifer Laverde
Grupo Química Básica, Aplicada y Ambiente-ALQUIMIA, Facultad de Ciencias Exactas y Aplicadas, Institución Universitaria ITM, Carrera 31 # 54-10, Medellín 050013, Colombia
2 shared publications - Carolina Mejía Salazar
Química de Recursos Energéticos y Medio Ambiente, Instituto de Química, Facultad de Ciencias Exactas y Naturales, Universidad de Antioquia, calle 70 No. 52-21, Medellín 050010, Colombia
1 shared publication - Nataly Carolina Rosero-Navarro
Instituto de Cerámica y Vidrio−CSIC, C/Kelsen 5, Madrid 28049, Spain
1 shared publication
Latest Publications
- 20 November 2024
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 16 (48) , 66181-66191
Demineralization of a Carbon Material Derived from Palm Kernel Shells as a Process for the Enhancement of the Electrochemical Performance of Lithium–Sulfur Cells
Carbon materials derived from biomass have been widely used in Li-S batteries; however, the mineral matter present in the biomass could impact the properties of the carbons and affect the electrochemical performance. In this study, the removal of mineral matter from palm kernel shells is reported to identify the effect of minerals on the physicochemical properties of the derived activated carbon and correlate them to the electrochemical performance in Li-S batteries. The content of minerals such as silicon, iron, and potassium was decreased by acid washing. The textural and conductive properties of activated carbon were increased by the absence of minerals. Electrochemical results reveal that the demineralized sample used as a sulfur host can increase the capacity for high charge and discharge rates by 23%. Hence, the removal of mineral matter in the biomass is an important step to consider for the application of activated carbons as sulfur hosts in Li-S batteries.
- 20 November 2024
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 16 (48) , 66181-66191
Demineralization of a Carbon Material Derived from Palm Kernel Shells as a Process for the Enhancement of the Electrochemical Performance of Lithium–Sulfur Cells
Carbon materials derived from biomass have been widely used in Li-S batteries; however, the mineral matter present in the biomass could impact the properties of the carbons and affect the electrochemical performance. In this study, the removal of mineral matter from palm kernel shells is reported to identify the effect of minerals on the physicochemical properties of the derived activated carbon and correlate them to the electrochemical performance in Li-S batteries. The content of minerals such as silicon, iron, and potassium was decreased by acid washing. The textural and conductive properties of activated carbon were increased by the absence of minerals. Electrochemical results reveal that the demineralized sample used as a sulfur host can increase the capacity for high charge and discharge rates by 23%. Hence, the removal of mineral matter in the biomass is an important step to consider for the application of activated carbons as sulfur hosts in Li-S batteries.
- Open Access
Influence of the Nitrogen Precursor in the Development of N-Functionalities in a Mesoporous Carbon Material and Its Effect on the Li–S Cells’ Electrochemistry
Li–S batteries are positioned as a strong alternative for efficient energy storage due to their high theoretical energy density and their theoretical specific capacity (1675 mA h g−1) compared to current Li-ion batteries; however, their commercialization is affected by the rapid decay of the specific capacity as a consequence of the different species of lithium polysulfides that are generated during the charge–discharge processes. The use of nitrogen-doped mesoporous carbon materials has been shown to have the ability to confer electronic conductivity to sulfur and retain the lithium polysulfide species. However, there are not enough studies to help understand how the type of nitrogen precursor influences the development of specific nitrogen functionalities to favor the retention of lithium polysulfide species. This work seeks to determine the effect of the use of different nitrogen precursors on the structural changes of the mesoporous carbon materials prepared, and thus evaluate the electrochemical behavior of Li–S cells correlating the type of nitrogen functionality generated when the precursor is variated with the charge/discharge capacity developed during the cell operation. For this study, different carbon materials were prepared by the variation of the nitrogen source (melamine, ethylenediamine, and hexadecylamine) to obtain a N-doped mesoporous carbon with different distributions of nitrogen functionalities in its structure. The use of the primary amine ethylenediamine as a nitrogen precursor in the formation of structured carbon materials favored elemental sulfur infiltration into its pores, resulting in the maximum sulfur content within the pores and interacting with the carbonaceous matrix (78.8 wt.%). The carbon material prepared with this precursor resulted in a higher content of N-pyridinic functionality, which, combined with the high content of N-pyrrolic, resulted in the highest specific discharge capacity at 0.1 C after 100 cycles when compared to cells assembled with materials derived from the use of melamine and hexadecylamine precursors. The cell assembled with the electrode formed from ethylenediamine as a nitrogen precursor presented an initial discharge capacity of 918 mA h g−1 with a Coulombic efficiency of ~83.4% at 0.1 C after 100 cycles.
Open AccessInfluence of the Nitrogen Precursor in the Development of N-Functionalities in a Mesoporous Carbon Material and Its Effect on the Li–S Cells’ Electrochemistry
Li–S batteries are positioned as a strong alternative for efficient energy storage due to their high theoretical energy density and their theoretical specific capacity (1675 mA h g−1) compared to current Li-ion batteries; however, their commercialization is affected by the rapid decay of the specific capacity as a consequence of the different species of lithium polysulfides that are generated during the charge–discharge processes. The use of nitrogen-doped mesoporous carbon materials has been shown to have the ability to confer electronic conductivity to sulfur and retain the lithium polysulfide species. However, there are not enough studies to help understand how the type of nitrogen precursor influences the development of specific nitrogen functionalities to favor the retention of lithium polysulfide species. This work seeks to determine the effect of the use of different nitrogen precursors on the structural changes of the mesoporous carbon materials prepared, and thus evaluate the electrochemical behavior of Li–S cells correlating the type of nitrogen functionality generated when the precursor is variated with the charge/discharge capacity developed during the cell operation. For this study, different carbon materials were prepared by the variation of the nitrogen source (melamine, ethylenediamine, and hexadecylamine) to obtain a N-doped mesoporous carbon with different distributions of nitrogen functionalities in its structure. The use of the primary amine ethylenediamine as a nitrogen precursor in the formation of structured carbon materials favored elemental sulfur infiltration into its pores, resulting in the maximum sulfur content within the pores and interacting with the carbonaceous matrix (78.8 wt.%). The carbon material prepared with this precursor resulted in a higher content of N-pyridinic functionality, which, combined with the high content of N-pyrrolic, resulted in the highest specific discharge capacity at 0.1 C after 100 cycles when compared to cells assembled with materials derived from the use of melamine and hexadecylamine precursors. The cell assembled with the electrode formed from ethylenediamine as a nitrogen precursor presented an initial discharge capacity of 918 mA h g−1 with a Coulombic efficiency of ~83.4% at 0.1 C after 100 cycles.