QQQin Qian

Qin Qian

*This is an algorithmically generated author record based on publicly available information.

Qin Qian has a total of 19 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Numerical Simulation and Optimization of Polyacrylamide Solution Flow in a Polymer Injector Using an Improved Viscosity Constitutive Model

    by Qin Qian, Tengyu Li, Congkun Ren, Yantao Zhou, Chuanrui Che, Xuemei Zhang, Jiaxing Ma, Pengxu An, Qiuyang Zhao

    Previous numerical simulations of polymer injectors often rely on fixed-viscosity models, which fail to accurately capture the severe shear degradation of non-Newtonian fluids under high-shear throttling conditions. To address this limitation and enhance polymer flooding efficiency, this study proposes an improved Carreau–Yasuda viscosity constitutive model to precisely simulate the flow behavior of polyacrylamide (HPAM) solutions. A comprehensive computational fluid dynamics (CFD) model was developed and validated, showing a viscosity prediction error of less than 8.6% across a wide shear rate range (0.1–10,000 s−1). Based on this dynamic rheological model, the internal flow channel of the injector was optimized, resulting in a novel spindle-type throttling unit. Simulation and field validation results demonstrate that the optimized structure achieves a significant pressure drop of 6.03 MPa at an injection flow rate of 96 m3/d—representing a 65% improvement over traditional designs—while successfully maintaining a viscosity retention rate above 85%. This research overcomes the traditional design conflict between high pressure reduction and viscosity preservation, providing an accurate numerical framework and practical guidance for engineering high-flow, robust-throttling polymer injectors.


  • Open Access

    Micro-Pore Structure and Fractal Characteristics of Shale Reservoir in Jiyang Depression

    by Qin Qian, Mingjing Lu, Anhai Zhong, Feng Yang, Wenjun He, Lei Li

    In order to better understand the micropore structure of shale reservoir in Jiyang Depression, permeability damage test, low temperature nitrogen adsorption and scanning electron microscopy (SEM) were carried out on six cores in the target block. The adsorption isotherms were analyzed by Frenkel–Halsey–Hill (FHH) model, and the fractal dimensions of different layers were calculated. The results show that the shale pore system is mainly composed of organic nanopores, inorganic nanopores and micro-fractures. The inorganic pores are mainly distributed around or inside the mineral particles, while microcracks are commonly found between mineral particles or at the organic–mineral interface. Organic pores are located within or between organic particles. The results of nitrogen adsorption show that the shale pores are mainly H2/H3 hysteresis loops with wedge, plate or ink bottle shapes. The pore structure is highly complex, and the fractal dimension is high. The mean D1 fractal dimension, which represents pore surface roughness, is 2.3788, and the mean D2 fractal dimension, which represents pore structure complexity, is 2.7189. The fractal dimension is positively correlated with specific surface area and total pore volume and negatively correlated with average pore radius. The permeability damage rates of the N layer, B layer, and F layer are 17.39%, 20.2%, and 21.6%, respectively. The contact Angle of the core decreases with the increase in water skiing time. In this study, the micropore structure of different formations in Jiyang Depression is compared and analyzed, which provides valuable insights for the optimization and differentiated development of shale oil and gas resources.


  • Open Access

    Experimental Study of Plugging Agent Particle Size and Concentration on Temporary Plugging Fracturing in Shale Formation

    by Feng Yang, Qin Qian, Mingjing Lu, Wenjun He, Anhai Zhong, Zilin Zhang, Danyang Zhu, Yushi Zou

    During the temporary plugging fracturing (TPF) process, the pressure response and pumping behavior significantly differ from those observed during conventional fracturing fluid pumping. Once the temporary plugging agent (TPA) forms a plug, subsequent fracture initiation and propagation become more intricate due to the influence of the TPA and early fractures. Factors such as concentration, particle size, and ratio of the TPA notably affect the effectiveness of TPF. This study employs a true triaxial hydraulic fracturing simulation system to conduct TPF experiments with varying particle size combinations and concentrations at both in-fracture and in-stage locations. The impact of different TPA parameters on the plugging effectiveness is assessed by analyzing the morphology of the induced fractures and the characteristics of pressure curves post experiment. Results indicate that combining dfferent particle sizes enhances plugging effectiveness, with a combination of smaller and larger particles exhibiting superior plugging effectiveness, resulting in a pressure increase of over 25.9%. As the concentration of the TPA increases, the plugging fracture pressure rises, accompanied by rapid pressure response and significant plugging effects, leading to more complex fracture morphology. For shale reservoirs, the density of bedding planes (BPs) influences the morphology and width of conventional hydraulic fractures, thereby affecting the effectiveness of subsequent refracturing. Rock samples with a relatively low BP density demonstrate effective plugging initiation both in-fracture and in-stage, facilitating the formation of complex fracture networks. Conversely, specimens with a relatively high BP density exhibit superior plugging effectiveness in-stage compared to in-fracture plugging.


  • Open Access

    Numerical modeling of micro-particle migration in channels

    by Dongying Wang, Qin Qian, Anhai Zhong, Mingjing Lu, Zilin Zhang

    Numerical modeling of micro-particle migration in channels