Luke Wadle
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Luke Wadle has a total of 33 co-authors. Here are the top co-authors by number of shared publications:
- Yongfeng Lu
Department of Electrical and Computer Engineering, University of Nebraska-Lincoln, Lincoln, NE 68588, USA
3 shared publications Bai Cui
2 shared publications- Bai Cui
Department of Mechanical & Materials Engineering University of Nebraska–Lincoln Lincoln Nebraska USA
2 shared publications - Haoyu Dong
Univ Nebraska, Dept Elect & Comp Engn, Lincoln, NE 68508 USA
2 shared publications - Jean-François Silvain
University Bordeaux, CNRS, Bordeaux INP, ICMCB, UMR 5026, Pessac, France
2 shared publications Patrick E. Albert
2 shared publications
Latest Publications
- 17 November 2026
- Published by Elsevier in Applied Surface Science
Glancing-angle femtosecond laser polishing of tantalum carbide
- 17 November 2026
- Published by Elsevier in Applied Surface Science
Glancing-angle femtosecond laser polishing of tantalum carbide
- Open Access
- 19 September 2026
- Published by Elsevier in SSRN Electronic Journal
Glancing-Angle Femtosecond Laser Polishing of Tantalum Carbide
Rapid, dimensionally accurate polishing of ultra-high-temperature ceramics remains difficult due to their hardness and brittleness, and how repeated ultrafast irradiation transforms a rough machined sidewall—and what limits further roughness reduction—is unclear. Glancing-angle femtosecond laser polishing of TaC in an ablation-dominated regime tracked morphological and chemical evolution with laser power and scan number. Roughness dropped rapidly as EDM topography was removed, then stabilized at 0.40–0.50 µm after a new sidewall formed. Raising power from 7.00 to 21.72 W reduced the scans needed for complete removal from 150 to 50; the lowest Sa of 0.400 µm was an 84.1% improvement over the initial EDM surface. Further scanning brought little additional smoothing but produced persistent 0.42–0.44 µm nanoripples of declining directional order and increased oxygen in the EDS sampling volume, while XPS showed a nearly constant Ta5+ fraction and O/Ta ratio, indicating a stable outermost oxide. Attainable roughness therefore reflects competition between fading EDM topography and growing laser-induced morphological and chemical modifications; a phenomenological model captured the two regimes and their transition. No microcracks were observed on the surface or in FIB cross-sections. The same approach reduced roughness of ZrB2 and cemented WC (BC-6S) by 77.2% and 74.4%, demonstrating versatility beyond TaC.
- 19 September 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessGlancing-Angle Femtosecond Laser Polishing of Tantalum Carbide
Rapid, dimensionally accurate polishing of ultra-high-temperature ceramics remains difficult due to their hardness and brittleness, and how repeated ultrafast irradiation transforms a rough machined sidewall—and what limits further roughness reduction—is unclear. Glancing-angle femtosecond laser polishing of TaC in an ablation-dominated regime tracked morphological and chemical evolution with laser power and scan number. Roughness dropped rapidly as EDM topography was removed, then stabilized at 0.40–0.50 µm after a new sidewall formed. Raising power from 7.00 to 21.72 W reduced the scans needed for complete removal from 150 to 50; the lowest Sa of 0.400 µm was an 84.1% improvement over the initial EDM surface. Further scanning brought little additional smoothing but produced persistent 0.42–0.44 µm nanoripples of declining directional order and increased oxygen in the EDS sampling volume, while XPS showed a nearly constant Ta5+ fraction and O/Ta ratio, indicating a stable outermost oxide. Attainable roughness therefore reflects competition between fading EDM topography and growing laser-induced morphological and chemical modifications; a phenomenological model captured the two regimes and their transition. No microcracks were observed on the surface or in FIB cross-sections. The same approach reduced roughness of ZrB2 and cemented WC (BC-6S) by 77.2% and 74.4%, demonstrating versatility beyond TaC.
- Open Access
- 22 May 2024
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 135 (20)
Compositionally complex carbide ceramics: A perspective on irradiation damage
Extensive experimental and computational studies have demonstrated outstanding physical and chemical properties of the novel materials of compositionally complex carbides (CCCs), enabling their promising applications in advanced fission and fusion energy systems. This perspective provides a comprehensive overview of radiation damage behavior reported in the literature to understand the fundamental mechanisms related to the impact of multi-principal metal components on phase stability, irradiation-induced defect clusters, irradiation hardening, and thermal conductivity of compositionally complex carbides. Several future research directions are recommended to critically evaluate the feasibility of designing and developing new ceramic materials for extreme environments using the transformative “multi-principal component” concept. Compared to the existing materials for nuclear applications including stainless steels, nickel alloys, ZrC, SiC, and potentially high-entropy alloys, as well as certain other compositionally complex ceramic families. CCCs appear to be more resistant to amorphization, growth of irradiation defect clusters, and void swelling.
- 22 May 2024
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 135 (20)
Open AccessCompositionally complex carbide ceramics: A perspective on irradiation damage
Extensive experimental and computational studies have demonstrated outstanding physical and chemical properties of the novel materials of compositionally complex carbides (CCCs), enabling their promising applications in advanced fission and fusion energy systems. This perspective provides a comprehensive overview of radiation damage behavior reported in the literature to understand the fundamental mechanisms related to the impact of multi-principal metal components on phase stability, irradiation-induced defect clusters, irradiation hardening, and thermal conductivity of compositionally complex carbides. Several future research directions are recommended to critically evaluate the feasibility of designing and developing new ceramic materials for extreme environments using the transformative “multi-principal component” concept. Compared to the existing materials for nuclear applications including stainless steels, nickel alloys, ZrC, SiC, and potentially high-entropy alloys, as well as certain other compositionally complex ceramic families. CCCs appear to be more resistant to amorphization, growth of irradiation defect clusters, and void swelling.