Jinghang Yang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Jinghang Yang has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
- Baoshun Zhang
Nanofabrication Facility, Suzhou institute of Nano-Tech and Nano-Bionics, Chinese Academy of Sciences, Suzhou 215123, China
1 shared publication - Changling Yan
State Key Lab on High Power Semiconductor lasers, Changchun University of Science and Technology, Changchun, China
1 shared publication - Cong Zhang
State Key Laboratory of High Power Semiconductor Laser, Changchun University of Science and Technology, Changchun 130022, China
1 shared publication - Huanyu Zhang
A Nanofabrication Facility, Suzhou Institute of Nano-Tech and Nano-Bionics, Chinese Academy of Sciences, Suzhou 215123, China
1 shared publication - Huimin Jia
State Key Laboratory of High Power Semiconductor Laser, Changchun University of Science and Technology, Changchun 130022, China
1 shared publication - Jilong Tang
State Key Laboratory of High Power Semiconductor Laser, Changchun University of Science and Technology, Changchun 130022, China
1 shared publication
Latest Publications
- Open Access
Structural Design and Experimental Investigation of a 1.65 µm Tapered Semiconductor Laser with InGaAlAs MQWs (On InP)
This paper presents the design and fabrication of a 1.65 μm tapered semiconductor laser based on an InGaAlAs multiple quantum well structure (grown) on InP. Through theoretical modeling and parametric optimization simulations, it was established that an etching depth of 0.8 μm for the ridge waveguide and a taper angle of 6° effectively confine the optical field and suppress high-order mode lasing. Based on these optimized parameters, a tapered semiconductor laser with a ridge width of 2 μm and a cavity length of 2000 μm was successfully fabricated. Systematic characterization was conducted under continuous-wave operation at 25 °C. The device exhibits outstanding overall performance: a maximum continuous-wave output power of 19.3 mW, a peak wavelength of 1653 nm, a spectral line width of 0.793 nm, and a side-mode suppression ratio (SMSR) as high as 49 dB, demonstrating excellent spectral purity. Far-field measurements further reveal that at an injection current of 30 mA, the vertical and horizontal far-field divergence angles are 41.02° and 15.26°, respectively, with a well-defined Gaussian beam profile. This study provides an effective technical approach for the design and fabrication of high-performance semiconductor lasers in the 1.65 μm band. The developed device shows significant potential for applications in free-space optical communication, LiDAR, and gas sensing.
Open AccessStructural Design and Experimental Investigation of a 1.65 µm Tapered Semiconductor Laser with InGaAlAs MQWs (On InP)
This paper presents the design and fabrication of a 1.65 μm tapered semiconductor laser based on an InGaAlAs multiple quantum well structure (grown) on InP. Through theoretical modeling and parametric optimization simulations, it was established that an etching depth of 0.8 μm for the ridge waveguide and a taper angle of 6° effectively confine the optical field and suppress high-order mode lasing. Based on these optimized parameters, a tapered semiconductor laser with a ridge width of 2 μm and a cavity length of 2000 μm was successfully fabricated. Systematic characterization was conducted under continuous-wave operation at 25 °C. The device exhibits outstanding overall performance: a maximum continuous-wave output power of 19.3 mW, a peak wavelength of 1653 nm, a spectral line width of 0.793 nm, and a side-mode suppression ratio (SMSR) as high as 49 dB, demonstrating excellent spectral purity. Far-field measurements further reveal that at an injection current of 30 mA, the vertical and horizontal far-field divergence angles are 41.02° and 15.26°, respectively, with a well-defined Gaussian beam profile. This study provides an effective technical approach for the design and fabrication of high-performance semiconductor lasers in the 1.65 μm band. The developed device shows significant potential for applications in free-space optical communication, LiDAR, and gas sensing.
- Open Access
Ultrahigh Responsivity In2O3 UVA Photodetector through Modulation of Trimethylindium Flow Rate
Oxygen vacancies (Vo) can significantly degrade the electrical properties of indium oxide (In2O3) thin films, thus limiting their application in the field of ultraviolet detection. In this work, the Vo is effectively suppressed by adjusting the Trimethylindium (TMIn) flow rate (fTMIn). In addition, with the reduction of the fTMIn, the background carrier concentration and the roughness of the film decrease gradually. And a smooth In2O3 thin film with roughness of 0.44 nm is obtained when the fTMIn is 5 sccm. The MSM photodetectors (PDs) are constructed based on In2O3 thin films with different fTMIn to investigate the opto-electric characteristics of the films. The dark current of the PDs is significantly reduced by five orders from 100 mA to 0.28 μA with the reduction of the fTMIn from 50 sccm to 5 sccm. In addition, the photo response capacity of PDs is dramatically enhanced. The photo-to-dark current ratio (PDCR) increases from 0 to 2589. Finally, the PD with the fTMIn of 5 sccm possesses a record-high responsivity of 2.53 × 103 AW−1, a high detectivity of 5.43 × 107 Jones and a high EQE of 9383 × 100%. Our work provides an important reference for the fabrication of high-sensitivity UV PDs.
Open AccessUltrahigh Responsivity In2O3 UVA Photodetector through Modulation of Trimethylindium Flow Rate
Oxygen vacancies (Vo) can significantly degrade the electrical properties of indium oxide (In2O3) thin films, thus limiting their application in the field of ultraviolet detection. In this work, the Vo is effectively suppressed by adjusting the Trimethylindium (TMIn) flow rate (fTMIn). In addition, with the reduction of the fTMIn, the background carrier concentration and the roughness of the film decrease gradually. And a smooth In2O3 thin film with roughness of 0.44 nm is obtained when the fTMIn is 5 sccm. The MSM photodetectors (PDs) are constructed based on In2O3 thin films with different fTMIn to investigate the opto-electric characteristics of the films. The dark current of the PDs is significantly reduced by five orders from 100 mA to 0.28 μA with the reduction of the fTMIn from 50 sccm to 5 sccm. In addition, the photo response capacity of PDs is dramatically enhanced. The photo-to-dark current ratio (PDCR) increases from 0 to 2589. Finally, the PD with the fTMIn of 5 sccm possesses a record-high responsivity of 2.53 × 103 AW−1, a high detectivity of 5.43 × 107 Jones and a high EQE of 9383 × 100%. Our work provides an important reference for the fabrication of high-sensitivity UV PDs.