Igor Vieira Fernandes
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Igor Vieira Fernandes has a total of 33 co-authors. Here are the top co-authors by number of shared publications:
- Antônio Acácio de Melo Neto
Universidade Federal de Pernambuco
9 shared publications - Carlos Fernando Gomes Do Nascimento
Doutorando, UFPE
7 shared publications - Marcos David dos Santos
Universidade Federal de Pernambuco
6 shared publications - Victor Marcelo Estolano de Lima
Polytechnic School, University of Pernambuco, Rua Benfica 455, Recife 50720-001, Brazil
4 shared publications - Danilo José da Costa Barbosa
Universidade Federal de Pernambuco
3 shared publications - Marina Cartaxo Braga Morais de Oliveira
Department of Civil and Environmental Engineering, Laboratory of Binder Technology, Federal University of Pernambuco, LabTag, Recife, Brazil
3 shared publications
Latest Publications
- Open Access
- 16 September 2026
- Published by Associacao Nacional de Tecnologia do Ambiente Construido (ANTAC) in ENCONTRO NACIONAL DE TECNOLOGIA DO AMBIENTE CONSTRUÍDO
- Vol. 21
Desempenho mecânico de argamassas de revestimento com substituição parcial do agregado miúdo por PET reciclado
The construction industry requires sustainable solutions to reduce the consumption of natural resources and promote the reuse of waste materials. In this context, this study evaluated the mechanical performance of rendering mortars with volumetric replacement of natural sand by 0%, 5%, 10%, and 15% PET. Compressive strength and flexural tensile strength were evaluated after 7, 14, 28, and 56 days of curing, while tensile bond strength was evaluated after 28 days. At 56 days, the mortar containing 15% PET exhibited compressive and flexural tensile strengths approximately 34% and 18% higher than those of the reference mortar, respectively, whereas tensile bond strength decreased by approximately 42%. Under the evaluated conditions, PET incorporation increased the mechanical strengths at 56 days, although it reduced tensile bond strength.
- 16 September 2026
- Published by Associacao Nacional de Tecnologia do Ambiente Construido (ANTAC) in ENCONTRO NACIONAL DE TECNOLOGIA DO AMBIENTE CONSTRUÍDO
- Vol. 21
Open AccessDesempenho mecânico de argamassas de revestimento com substituição parcial do agregado miúdo por PET reciclado
The construction industry requires sustainable solutions to reduce the consumption of natural resources and promote the reuse of waste materials. In this context, this study evaluated the mechanical performance of rendering mortars with volumetric replacement of natural sand by 0%, 5%, 10%, and 15% PET. Compressive strength and flexural tensile strength were evaluated after 7, 14, 28, and 56 days of curing, while tensile bond strength was evaluated after 28 days. At 56 days, the mortar containing 15% PET exhibited compressive and flexural tensile strengths approximately 34% and 18% higher than those of the reference mortar, respectively, whereas tensile bond strength decreased by approximately 42%. Under the evaluated conditions, PET incorporation increased the mechanical strengths at 56 days, although it reduced tensile bond strength.
- Open Access
- 17 March 2026
- Published by Springer Nature in Journal of Building Pathology and Rehabilitation
- Vol. 11 (2) , 129
Assessment of the pozzolanic activity of supplementary cementitious materials through electrical conductivity: a systematic methodological review with a scientometric approach
This study presents a systematic methodological review supported by a scientometric approach on the use of electrical conductivity (EC) to assess the pozzolanic activity of supplementary cementitious materials (SCMs). The increasing demand for sustainable alternatives to Portland cement has intensified the development of new SCMs, reinforcing the need for rapid and reliable methods to evaluate their reactivity. Electrical conductivity-based tests have gained attention due to their simplicity, low cost, and sensitivity to ionic variations during pozzolanic reactions; however, their methodological consistency and interpretative robustness remain debated. A total of 103 articles published between 1989 and 2025 were systematically selected from the Scopus and Web of Science databases. Scientometric analyses were employed to characterize the temporal evolution of the field, its main contributors, journals, collaboration networks, and influential documents. In parallel, the 20 most cited studies were examined in depth to identify experimental parameters, testing configurations, and data treatment strategies. Multivariate analyses, including Principal Component Analysis and Multiple Correspondence Analysis, were applied to reveal recurrent quantitative and qualitative methodological patterns. The results indicate sustained growth in scientific production, combined with pronounced heterogeneity in EC testing protocols. This variability helps explain recurrent inconsistencies reported in the literature, particularly discrepancies with mechanical performance, limitations of blank correction procedures, uncertainties regarding reaction mechanisms, and atypical conductivity behavior under high calcium hydroxide contents. Overall, EC is confirmed as a valuable tool for rapid screening and early-stage assessment, although its use as a standalone indicator of pozzolanic activity remains limited.
- 17 March 2026
- Published by Springer Nature in Journal of Building Pathology and Rehabilitation
- Vol. 11 (2) , 129
Open AccessAssessment of the pozzolanic activity of supplementary cementitious materials through electrical conductivity: a systematic methodological review with a scientometric approach
This study presents a systematic methodological review supported by a scientometric approach on the use of electrical conductivity (EC) to assess the pozzolanic activity of supplementary cementitious materials (SCMs). The increasing demand for sustainable alternatives to Portland cement has intensified the development of new SCMs, reinforcing the need for rapid and reliable methods to evaluate their reactivity. Electrical conductivity-based tests have gained attention due to their simplicity, low cost, and sensitivity to ionic variations during pozzolanic reactions; however, their methodological consistency and interpretative robustness remain debated. A total of 103 articles published between 1989 and 2025 were systematically selected from the Scopus and Web of Science databases. Scientometric analyses were employed to characterize the temporal evolution of the field, its main contributors, journals, collaboration networks, and influential documents. In parallel, the 20 most cited studies were examined in depth to identify experimental parameters, testing configurations, and data treatment strategies. Multivariate analyses, including Principal Component Analysis and Multiple Correspondence Analysis, were applied to reveal recurrent quantitative and qualitative methodological patterns. The results indicate sustained growth in scientific production, combined with pronounced heterogeneity in EC testing protocols. This variability helps explain recurrent inconsistencies reported in the literature, particularly discrepancies with mechanical performance, limitations of blank correction procedures, uncertainties regarding reaction mechanisms, and atypical conductivity behavior under high calcium hydroxide contents. Overall, EC is confirmed as a valuable tool for rapid screening and early-stage assessment, although its use as a standalone indicator of pozzolanic activity remains limited.
- Open Access
- 2 February 2026
- Published by Springer Nature in Arabian Journal for Science and Engineering
- Vol. 51 (10) , 13443-13473
Effects of Expanded Vermiculite on the Autogenous and Drying Shrinkage of Alkali-Activated Slag-Based Mortars
The growing need to reduce CO 2 emissions has encouraged the use of alkali-activated materials as sustainable alternatives to Portland cement. However, these binders are often susceptible to significant autogenous and drying shrinkage, which can compromise dimensional stability and durability. This study evaluates the influence of expanded vermiculite (EV) on the autogenous and drying shrinkage behavior of alkali-activated slag mortars. Mixtures containing 5%, 10%, and 15% EV were produced under dry, 100%, and 200% pre-saturation conditions, with a constant binder-to-aggregate ratio of 1:2 and a (w/b) ratio of 0.48. Physical and mechanical performance was analyzed through consistency, air content, density, compressive strength, capillary absorption, and microtomography tests. The results indicated that increasing the vermiculite content reduced the bulk density by up to 9.1% and increased the incorporated air content, which in turn decreased compressive strength by up to 31.4%. Capillary water absorption rose markedly in mixtures with 15% EV at 200% pre-saturation after 90 min. Autogenous shrinkage decreased by 66.4% in mixtures with dry EV, and 200% pre-saturation produced an additional 36.1% reduction. These results demonstrate that the moisture state of EV strongly governs shrinkage and pore connectivity in alkali-activated mortars. Controlled internal curing enhances dimensional stability while limiting strength losses when EV saturation and w/b are properly balanced. A forthcoming life-cycle assessment will quantify the environmental trade-offs of incorporating EV as an internal-curing agent.
- 2 February 2026
- Published by Springer Nature in Arabian Journal for Science and Engineering
- Vol. 51 (10) , 13443-13473
Open AccessEffects of Expanded Vermiculite on the Autogenous and Drying Shrinkage of Alkali-Activated Slag-Based Mortars
The growing need to reduce CO 2 emissions has encouraged the use of alkali-activated materials as sustainable alternatives to Portland cement. However, these binders are often susceptible to significant autogenous and drying shrinkage, which can compromise dimensional stability and durability. This study evaluates the influence of expanded vermiculite (EV) on the autogenous and drying shrinkage behavior of alkali-activated slag mortars. Mixtures containing 5%, 10%, and 15% EV were produced under dry, 100%, and 200% pre-saturation conditions, with a constant binder-to-aggregate ratio of 1:2 and a (w/b) ratio of 0.48. Physical and mechanical performance was analyzed through consistency, air content, density, compressive strength, capillary absorption, and microtomography tests. The results indicated that increasing the vermiculite content reduced the bulk density by up to 9.1% and increased the incorporated air content, which in turn decreased compressive strength by up to 31.4%. Capillary water absorption rose markedly in mixtures with 15% EV at 200% pre-saturation after 90 min. Autogenous shrinkage decreased by 66.4% in mixtures with dry EV, and 200% pre-saturation produced an additional 36.1% reduction. These results demonstrate that the moisture state of EV strongly governs shrinkage and pore connectivity in alkali-activated mortars. Controlled internal curing enhances dimensional stability while limiting strength losses when EV saturation and w/b are properly balanced. A forthcoming life-cycle assessment will quantify the environmental trade-offs of incorporating EV as an internal-curing agent.
- Open Access
- 1 January 2026
- Published by FapUNIFESP (SciELO) in Anais da Academia Brasileira de Ciências
- Vol. 98 (3)
Comparative Case-Study Analysis of Lightweight and Conventional Concrete in Structural Elements of a Multi-Story Building
This study evaluates the structural implications of adopting lightweight concrete (LC) in multistory buildings, with emphasis on columns – a configuration seldom examined. Three models of the same fourstory building – (i) all conventional concrete (CC), (ii) LC in slabs and beams (CLC), and (iii) LC in slabs, beams, and columns (LC) – were analyzed in AltoQi Eberick V10. Verifications followed NBR 6118 (ABNT 2023a); where NBR 6118 does not prescribe LC material properties, ACI 318-19 (ACI 2019) was used for the elastic modulus and EN 199211 (CEN 2004) for the densitybased tensile adjustment. Results show foundation loads decreased by up to 12.8% and total steel consumption by up to 13.7% with LC, while lateral displacements remained within code limits. Applying LC in columns increased the global instability index to γz = 1.10 yet retained a nonsway classification. The column case clarifies the tradeoff between weight reduction and increased deformability and provides codeanchored guidance for safe adoption in Brazilian practice. Overall, the findings indicate that LC is structurally viable and materially efficient for multistory buildings under NBR-based design, and highlight priorities for detailing and stiffness control when columns are also cast with LC.
- 1 January 2026
- Published by FapUNIFESP (SciELO) in Anais da Academia Brasileira de Ciências
- Vol. 98 (3)
Open AccessComparative Case-Study Analysis of Lightweight and Conventional Concrete in Structural Elements of a Multi-Story Building
This study evaluates the structural implications of adopting lightweight concrete (LC) in multistory buildings, with emphasis on columns – a configuration seldom examined. Three models of the same fourstory building – (i) all conventional concrete (CC), (ii) LC in slabs and beams (CLC), and (iii) LC in slabs, beams, and columns (LC) – were analyzed in AltoQi Eberick V10. Verifications followed NBR 6118 (ABNT 2023a); where NBR 6118 does not prescribe LC material properties, ACI 318-19 (ACI 2019) was used for the elastic modulus and EN 199211 (CEN 2004) for the densitybased tensile adjustment. Results show foundation loads decreased by up to 12.8% and total steel consumption by up to 13.7% with LC, while lateral displacements remained within code limits. Applying LC in columns increased the global instability index to γz = 1.10 yet retained a nonsway classification. The column case clarifies the tradeoff between weight reduction and increased deformability and provides codeanchored guidance for safe adoption in Brazilian practice. Overall, the findings indicate that LC is structurally viable and materially efficient for multistory buildings under NBR-based design, and highlight priorities for detailing and stiffness control when columns are also cast with LC.
- Open Access
- 25 November 2025
- Published by MDPI AG in Construction Materials
- Vol. 5 (4) , 84
Assessing the Effects of Activator Formulation on Hardened Properties of Alkali-Activated Slag Mortars Using Ultrasound Pulse Velocity (UPV) Technique
The UPV technique has been widely employed to predict the hardened properties of Portland cement mixtures. This article assesses the hardened properties of alkali-activated blast furnace slag mortars by comparing UPV measurements with compressive strength and dry density and calculating the dynamic modulus of elasticity from UPV results. The mixtures were prepared varying the type of activator (sodium metasilicate and sodium silicate), the content of Na2O in the activators (3.0, 4.5, 6.0, and 7.5%), and the water/binder ratio. The results showed that exponential models showed medium and high determination coefficients (R2), which explained the correlation between UPV and hardened properties. It was observed a limitation on the measurements of UPV, which did not surpass 4.4 km/s, which made it difficult to predict compressive strength value above 50 MPa. The dynamic modulus of elasticity calculated from UPV showed reliable results, even varying the Poisson’s coefficient between 0.15 and 0.25. Lastly, it was also observed that a correlation between the content of C-S-H and UPV suggested that this technique can also be used to predict the evolution of the hydration products in alkali-activated slag mixtures.
- 25 November 2025
- Published by MDPI AG in Construction Materials
- Vol. 5 (4) , 84
Open AccessAssessing the Effects of Activator Formulation on Hardened Properties of Alkali-Activated Slag Mortars Using Ultrasound Pulse Velocity (UPV) Technique
The UPV technique has been widely employed to predict the hardened properties of Portland cement mixtures. This article assesses the hardened properties of alkali-activated blast furnace slag mortars by comparing UPV measurements with compressive strength and dry density and calculating the dynamic modulus of elasticity from UPV results. The mixtures were prepared varying the type of activator (sodium metasilicate and sodium silicate), the content of Na2O in the activators (3.0, 4.5, 6.0, and 7.5%), and the water/binder ratio. The results showed that exponential models showed medium and high determination coefficients (R2), which explained the correlation between UPV and hardened properties. It was observed a limitation on the measurements of UPV, which did not surpass 4.4 km/s, which made it difficult to predict compressive strength value above 50 MPa. The dynamic modulus of elasticity calculated from UPV showed reliable results, even varying the Poisson’s coefficient between 0.15 and 0.25. Lastly, it was also observed that a correlation between the content of C-S-H and UPV suggested that this technique can also be used to predict the evolution of the hydration products in alkali-activated slag mixtures.
- Open Access
- 11 October 2025
- Published by Associacao Nacional de Tecnologia do Ambiente Construido (ANTAC) in Encontro Latino-americano e Europeu sobre Edificações e Comunidades Sustentáveis (euroELECS)
- Vol. 6
Avaliação das propriedades físicas de argamassas com substituição parcial do agregado miúdo por PET reciclado
A construção civil é um setor de grande relevância socioeconômica, mas também está entre os principais consumidores de recursos naturais e geradores de resíduos. Diante da crescente demanda por práticas sustentáveis, este trabalho avalia a substituição parcial do agregado miúdo natural por politereftalato de etileno (PET) reciclado em argamassas. Foram produzidas misturas com 0%, 5%, 10% e 15% de substituição, analisando-se propriedades físicas nos estados fresco e endurecido. O PET foi caracterizado quanto à densidade, granulometria, composição térmica e mineralógica, confirmando sua baixa densidade e estrutura parcialmente cristalina. Em seguida, realizaram-se ensaios de índice de consistência, densidade de massa fresca, teor de ar incorporado, absorção por capilaridade e densidade de massa aparente. Os resultados mostraram que a adição de PET reduziu a densidade da argamassa e os índices de absorção, permitindo a obtenção da consistência desejada com menor consumo de água. Esses efeitos se devem à baixa densidade e à granulometria fina do PET, que favorecem o empacotamento das partículas. Conclui-se que o PET reciclado é uma alternativa promissora para a produção de argamassas mais leves e potencialmente mais duráveis.
- 11 October 2025
- Published by Associacao Nacional de Tecnologia do Ambiente Construido (ANTAC) in Encontro Latino-americano e Europeu sobre Edificações e Comunidades Sustentáveis (euroELECS)
- Vol. 6
Open AccessAvaliação das propriedades físicas de argamassas com substituição parcial do agregado miúdo por PET reciclado
A construção civil é um setor de grande relevância socioeconômica, mas também está entre os principais consumidores de recursos naturais e geradores de resíduos. Diante da crescente demanda por práticas sustentáveis, este trabalho avalia a substituição parcial do agregado miúdo natural por politereftalato de etileno (PET) reciclado em argamassas. Foram produzidas misturas com 0%, 5%, 10% e 15% de substituição, analisando-se propriedades físicas nos estados fresco e endurecido. O PET foi caracterizado quanto à densidade, granulometria, composição térmica e mineralógica, confirmando sua baixa densidade e estrutura parcialmente cristalina. Em seguida, realizaram-se ensaios de índice de consistência, densidade de massa fresca, teor de ar incorporado, absorção por capilaridade e densidade de massa aparente. Os resultados mostraram que a adição de PET reduziu a densidade da argamassa e os índices de absorção, permitindo a obtenção da consistência desejada com menor consumo de água. Esses efeitos se devem à baixa densidade e à granulometria fina do PET, que favorecem o empacotamento das partículas. Conclui-se que o PET reciclado é uma alternativa promissora para a produção de argamassas mais leves e potencialmente mais duráveis.
- Open Access
- 30 September 2025
- Published by Associacao Nacional de Tecnologia do Ambiente Construido (ANTAC) in Encontro Latino-americano e Europeu sobre Edificações e Comunidades Sustentáveis (euroELECS)
- Vol. 6
Uso e aplicação do lodo de estação de tratamento de água na construção civil
O crescimento urbano intensificou a geração de lodo de estações de tratamento de água (LETA), cuja disposição enfrenta desafios técnicos, ambientais e econômicos. Diante da limitação de áreas para descarte e das exigências regulatórias, o reaproveitamento desse resíduo na construção surge como uma alternativa viável. O trabalho tem como objetivo realizar uma análise bibliométrica sobre o uso e aplicação do LETA na construção civil, de modo a identificar as principais áreas de emprego dos resíduos. A metodologia adotada combina abordagens quantitativa e qualitativa, com base na análise de documentos publicados de 1990 até setembro de 2023. Os resultados indicaram um aumento significativo das publicações a partir de 2015, refletindo o crescimento da preocupação ambiental e da regulação normativa. As áreas de ciência ambiental e engenharia concentram a maior parte das contribuições, evidenciando a natureza multidisciplinar do tema. A análise bibliométrica realizada com o VOSviewer identificou autores e palavras recorrentes, com ênfase em reaproveitamento sustentável e caracterização do resíduo. O LETA pode ser utilizado na fabricação de materiais cerâmicos, bem como em compostos cimentícios. O levantamento de tais informações auxiliam na consolidação do conhecimento e no direcionamento de pesquisas futuras.
- 30 September 2025
- Published by Associacao Nacional de Tecnologia do Ambiente Construido (ANTAC) in Encontro Latino-americano e Europeu sobre Edificações e Comunidades Sustentáveis (euroELECS)
- Vol. 6
Open AccessUso e aplicação do lodo de estação de tratamento de água na construção civil
O crescimento urbano intensificou a geração de lodo de estações de tratamento de água (LETA), cuja disposição enfrenta desafios técnicos, ambientais e econômicos. Diante da limitação de áreas para descarte e das exigências regulatórias, o reaproveitamento desse resíduo na construção surge como uma alternativa viável. O trabalho tem como objetivo realizar uma análise bibliométrica sobre o uso e aplicação do LETA na construção civil, de modo a identificar as principais áreas de emprego dos resíduos. A metodologia adotada combina abordagens quantitativa e qualitativa, com base na análise de documentos publicados de 1990 até setembro de 2023. Os resultados indicaram um aumento significativo das publicações a partir de 2015, refletindo o crescimento da preocupação ambiental e da regulação normativa. As áreas de ciência ambiental e engenharia concentram a maior parte das contribuições, evidenciando a natureza multidisciplinar do tema. A análise bibliométrica realizada com o VOSviewer identificou autores e palavras recorrentes, com ênfase em reaproveitamento sustentável e caracterização do resíduo. O LETA pode ser utilizado na fabricação de materiais cerâmicos, bem como em compostos cimentícios. O levantamento de tais informações auxiliam na consolidação do conhecimento e no direcionamento de pesquisas futuras.
- 29 August 2025
- Published by Elsevier in Journal of Building Engineering
- Vol. 112
Physicochemical and microstructural interactions between cement and textile sludge ash for application in dry concrete
- 29 August 2025
- Published by Elsevier in Journal of Building Engineering
- Vol. 112
Physicochemical and microstructural interactions between cement and textile sludge ash for application in dry concrete