Juan Manuel Redondo
Research Subjects
Juan Manuel Redondo has a total of 52 co-authors. Here are the top co-authors by number of shared publications:
- Javier Malo
E.T.S. de Ingeniería Y Sistemas de Telecomunicación, UPM Madrid Spain
3 shared publications - Alejandro Fernández-Soler
Universidad Politcnica de Madrid, Madrid, Spain
2 shared publications - Blanca Boado-Cuartero
Universidad Politcnica de Madrid, Madrid, Spain
2 shared publications - David González-Bárcena
Universidad Politcnica de Madrid, Madrid, Spain
2 shared publications - Francisco Martín
Instituto de Energía Solar‐Universidad Politécnica de Madrid (IES‐UPM) Madrid Spain
2 shared publications - Luis Javier San José
Universidad Politécnica de Madrid
2 shared publications
Latest Publications
- Open Access
- 24 March 2026
- Published by Wiley in Progress in Photovoltaics: Research and Applications
- Vol. 34 (6) , 744-757
Testing VIPV Curved Modules: Methods and Challenges
Vehicle‐integrated photovoltaics (VIPV) offer a promising pathway to increase electric‐vehicle autonomy, yet their characterization is challenged by curved geometries and non‐uniform irradiance conditions. This work presents and validates a comprehensive methodology for the characterization of curved photovoltaic modules. Standard test condition (STC) I–V curves and relative angular response (RAR) measurements are performed on a set of one‐dimensional cylindrical modules with varying curvature radii as well as on a commercial two‐dimensional curved VIPV module. Outdoor measurements using a dual‐axis programmable solar tracker are systematically compared with indoor measurements obtained using a collimated‐light solar simulator. Results demonstrate excellent agreement between indoor and outdoor STC I–V curves, with deviations below 1.5%, confirming the suitability of collimated solar simulation for rating curved PV modules. The study further analyzes the impact of curvature, temperature, and diffuse irradiance on angular response and proposes best practices to reduce measurement dispersion. These findings provide a robust experimental foundation for future standardization of VIPV characterization procedures.
- 24 March 2026
- Published by Wiley in Progress in Photovoltaics: Research and Applications
- Vol. 34 (6) , 744-757
Open AccessTesting VIPV Curved Modules: Methods and Challenges
Vehicle‐integrated photovoltaics (VIPV) offer a promising pathway to increase electric‐vehicle autonomy, yet their characterization is challenged by curved geometries and non‐uniform irradiance conditions. This work presents and validates a comprehensive methodology for the characterization of curved photovoltaic modules. Standard test condition (STC) I–V curves and relative angular response (RAR) measurements are performed on a set of one‐dimensional cylindrical modules with varying curvature radii as well as on a commercial two‐dimensional curved VIPV module. Outdoor measurements using a dual‐axis programmable solar tracker are systematically compared with indoor measurements obtained using a collimated‐light solar simulator. Results demonstrate excellent agreement between indoor and outdoor STC I–V curves, with deviations below 1.5%, confirming the suitability of collimated solar simulation for rating curved PV modules. The study further analyzes the impact of curvature, temperature, and diffuse irradiance on angular response and proposes best practices to reduce measurement dispersion. These findings provide a robust experimental foundation for future standardization of VIPV characterization procedures.
- 6 June 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Aerospace and Electronic Systems Magazine
- Vol. 40 (11) , 4-17
Design of a COTS-Based, Low-Cost, Electronic Box to Standardize Student Balloon Applications
Stratospheric balloons are a valuable platform for scientific and technological experiments, as they can reach altitudes of 20 to 40 km and stay aloft for weeks or months. However, designing electronic boxes for stratospheric balloons poses several challenges, such as thermal management, mechanical stability, power consumption, and communication. The electronic box contains the main components of an experiment, such as the payload interface, the telemetry system, the data acquisition and storage, the sensors and actuators, and the power supply. This article presents some of the best practices and lessons learned from the experience of developing and testing an electronic box for the experiment HERCCULES, inside the stratospheric balloon of the BEXUS/REXUS program. The design criteria and trade-offs that were considered for each component, such as weight, size, reliability, modularity, and compatibility, are also discussed. A low-cost design with outstanding performance was obtained based on a concept that can serve as a baseline for the standardization of payload electronics of stratospheric balloons.
- 6 June 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Aerospace and Electronic Systems Magazine
- Vol. 40 (11) , 4-17
Design of a COTS-Based, Low-Cost, Electronic Box to Standardize Student Balloon Applications
Stratospheric balloons are a valuable platform for scientific and technological experiments, as they can reach altitudes of 20 to 40 km and stay aloft for weeks or months. However, designing electronic boxes for stratospheric balloons poses several challenges, such as thermal management, mechanical stability, power consumption, and communication. The electronic box contains the main components of an experiment, such as the payload interface, the telemetry system, the data acquisition and storage, the sensors and actuators, and the power supply. This article presents some of the best practices and lessons learned from the experience of developing and testing an electronic box for the experiment HERCCULES, inside the stratospheric balloon of the BEXUS/REXUS program. The design criteria and trade-offs that were considered for each component, such as weight, size, reliability, modularity, and compatibility, are also discussed. A low-cost design with outstanding performance was obtained based on a concept that can serve as a baseline for the standardization of payload electronics of stratospheric balloons.
- Open Access
- 25 July 2024
- Published by Elsevier in Solar Energy Materials and Solar Cells
- Vol. 276
Relative angular response characterization in VIPV
- 25 July 2024
- Published by Elsevier in Solar Energy Materials and Solar Cells
- Vol. 276
Open AccessRelative angular response characterization in VIPV
- Open Access
- 26 April 2024
- Published by Elsevier in Acta Astronautica
- Vol. 220, 305-320
HERCCULES: A university balloon-borne experiment for BEXUS 32 to characterize the thermal environment in the stratosphere using COTS
- 26 April 2024
- Published by Elsevier in Acta Astronautica
- Vol. 220, 305-320
Open AccessHERCCULES: A university balloon-borne experiment for BEXUS 32 to characterize the thermal environment in the stratosphere using COTS