Elígia Simionato
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Elígia Simionato has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Rafael Abrantes Penchel
School of Engineering, So Paulo State University (Unesp), So Joo da Boa Vista, So Paulo, Brazil
4 shared publications - Guilherme Simon Rosa
São Paulo State University (UNESP)
3 shared publications - Ariana Lacorte Caniato Serrano
University of São Paulo
2 shared publications Gustavo P. Rehder
Univ Sao Paulo, Polytech Sch, Ave Prof Luciano Gualberto, Travessa Politecn, 380, BR-05508010 Sao Paulo, SP, Brazil
2 shared publications- Ivan Aldaya
School of Engineering, São Paulo State University (UNESP), São João da Boa Vista, Brazil
2 shared publications Andre L. Jardini
National Institute of Science and Technology in Biomanufacturing, Faculty of Chemical Engineering, University of Campinas, Campinas, Brazil
1 shared publication
Latest Publications
- 10 July 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 73 (1) , 482-493
A Variational Rayleigh–Ritz Method for Modeling H -Plane Bend Rectangular Waveguides
This article introduces a novel variational formula for modeling waveguides with uniformly curved longitudinal axes. Using the Rayleigh–Ritz method, we analyze the electromagnetic fields in $H$ -plane bend rectangular waveguides. In addition, we present a Galerkin method solution (GMS) for discretizing the associated vector Helmholtz equation within a local curved coordinate system. The proposed methodologies are validated through comparison with analytical results and a Galerkin-based solution from the literature across several representative scenarios. The rate of convergence, with respect to the number of expansion terms in the Rayleigh–Ritz method solution (RRMS), is observed to be faster than that in Galerkin-based solutions, while requiring comparable computational times. Furthermore, we explore the impact of both dielectric and conduction losses via the Rayleigh–Ritz method, aspects previously unattainable with analytical methods.
- 10 July 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 73 (1) , 482-493
A Variational Rayleigh–Ritz Method for Modeling H -Plane Bend Rectangular Waveguides
This article introduces a novel variational formula for modeling waveguides with uniformly curved longitudinal axes. Using the Rayleigh–Ritz method, we analyze the electromagnetic fields in $H$ -plane bend rectangular waveguides. In addition, we present a Galerkin method solution (GMS) for discretizing the associated vector Helmholtz equation within a local curved coordinate system. The proposed methodologies are validated through comparison with analytical results and a Galerkin-based solution from the literature across several representative scenarios. The rate of convergence, with respect to the number of expansion terms in the Rayleigh–Ritz method solution (RRMS), is observed to be faster than that in Galerkin-based solutions, while requiring comparable computational times. Furthermore, we explore the impact of both dielectric and conduction losses via the Rayleigh–Ritz method, aspects previously unattainable with analytical methods.
- Open Access
- 27 May 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of Antennas and Propagation
- Vol. 5 (4) , 1121-1132
Design Guidelines and Performance Analysis of a Wideband Coaxial Horn Antenna Fabricated via Additive Manufacturing
This work introduces a Ka-band coaxial horn antenna that incorporates a specialized dielectric supporting structure and a transition to a 2.4 mm connector. The inner and outer radii of the coaxial aperture were sized using an approximated model for an open-ended coaxial waveguide. The theory of small reflections was then used to account for the reflection coefficient resulting from an additional cascading cylindrical-conical section. A refined numerical model, representing more accurately a prototype, featured a transition region to standardized connectors and a dielectric structure that offers mechanical support for the inner conductor and impedance matching. Ansys HFSS full-wave electromagnetic finite-element method solver was used to compute the parameters of the antenna, and a genetic algorithm optimizer was employed to improve the performance of the complete coaxial horn. A prototype was fabricated using metal additive manufacturing for the inner and outer horn conductors, while the dielectric support was created using 3D polymer printing. Experimental measurements demonstrate that the prototyped antenna has an impedance bandwidth of above 79.36% (19–44 GHz), a peak realized gain of 11.53 dBi, and a maximum efficiency of 89.83%. Additionally, a sensitivity analysis was conducted to evaluate the potential impact of additive manufacturing imperfections and assembly errors on the antenna’s performance.
- 27 May 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of Antennas and Propagation
- Vol. 5 (4) , 1121-1132
Open AccessDesign Guidelines and Performance Analysis of a Wideband Coaxial Horn Antenna Fabricated via Additive Manufacturing
This work introduces a Ka-band coaxial horn antenna that incorporates a specialized dielectric supporting structure and a transition to a 2.4 mm connector. The inner and outer radii of the coaxial aperture were sized using an approximated model for an open-ended coaxial waveguide. The theory of small reflections was then used to account for the reflection coefficient resulting from an additional cascading cylindrical-conical section. A refined numerical model, representing more accurately a prototype, featured a transition region to standardized connectors and a dielectric structure that offers mechanical support for the inner conductor and impedance matching. Ansys HFSS full-wave electromagnetic finite-element method solver was used to compute the parameters of the antenna, and a genetic algorithm optimizer was employed to improve the performance of the complete coaxial horn. A prototype was fabricated using metal additive manufacturing for the inner and outer horn conductors, while the dielectric support was created using 3D polymer printing. Experimental measurements demonstrate that the prototyped antenna has an impedance bandwidth of above 79.36% (19–44 GHz), a peak realized gain of 11.53 dBi, and a maximum efficiency of 89.83%. Additionally, a sensitivity analysis was conducted to evaluate the potential impact of additive manufacturing imperfections and assembly errors on the antenna’s performance.
- Open Access
- 22 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 12, 22132-22143
Implementation of a Millimeter-Wave Butler Matrix on Metallic Nanowires-Filled Membrane Platform
Wireless communications with greater transmission capacities are possible in the millimeter wave (mmWave) region. However, to overcome the significant propagation losses in this frequency band, it is necessary to employ more efficient and intelligent antennas based on MIMO and beam-steering phased array technologies. This paper demonstrates the fabrication of a beam steerable array antenna using a 4 × 4 Butler matrix at 60 GHz employing the metallic nanowire membrane (MnM) substrate. This substrate has the advantage of interconnecting two metallization layers by vias fabricated through its nanopores. Experimental characterization of the fabricated samples shows that the MnM platform represents a high-potential candidate for millimeter-wave front-ends supporting the beam-steering technique.
- 22 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 12, 22132-22143
Open AccessImplementation of a Millimeter-Wave Butler Matrix on Metallic Nanowires-Filled Membrane Platform
Wireless communications with greater transmission capacities are possible in the millimeter wave (mmWave) region. However, to overcome the significant propagation losses in this frequency band, it is necessary to employ more efficient and intelligent antennas based on MIMO and beam-steering phased array technologies. This paper demonstrates the fabrication of a beam steerable array antenna using a 4 × 4 Butler matrix at 60 GHz employing the metallic nanowire membrane (MnM) substrate. This substrate has the advantage of interconnecting two metallization layers by vias fabricated through its nanopores. Experimental characterization of the fabricated samples shows that the MnM platform represents a high-potential candidate for millimeter-wave front-ends supporting the beam-steering technique.