P. V. Golinitskii
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
P. V. Golinitskii has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
U. Yu. Antonova
Russian State Agrarian University—Moscow Timiryazev Agricultural Academy, Moscow, Russia
5 shared publicationsE. I. Cherkasova
Russian State Agrarian University—Moscow Timiryazev Agricultural Academy, Moscow, Russia
4 shared publicationsG. N. Temasova
Russian State Agrarian University—Moscow Timiryazev Agricultural Academy, Moscow, Russia
2 shared publications- Uliana Antonova
Russian State Agrarian University - Moscow Timiryazev Agricultural Academy, Moscow, 127434, Russia
2 shared publications A. N. Samordin
Russian State Agrarian University—Moscow Timiryazev Agricultural Academy, Moscow, Russia
1 shared publicationD. A. Pupkova
Russian State Agrarian University—Moscow Timiryazev Agricultural Academy, Moscow, Russia
1 shared publication
Latest Publications
- 3 October 2026
- Published by Pleiades Publishing Ltd in Journal of Machinery Manufacture and Reliability
- Vol. 55 (5) , 469-476
Providing Reliable Interference Fits of Rolling Bearings in Transfer Gearboxes
The off-road operation of machines requires for specialized training and equipment that makes it possible to provide its mobility even under challenging conditions with frequent overloading. In this regard, increased requirements are imposed on vehicle components, for which it is neccessary to provide precision in assembling thereof. One of the key components that makes it possible to transmits torque between the drive axles can be represented by a transfer gearbox, whose reliability determines the operability of the vehicle. In this paper, studies concerning the fit reliability of the L0/k6 rolling bearings in the GAZ transfer gearbox of the GAZ vehicle.
- 3 October 2026
- Published by Pleiades Publishing Ltd in Journal of Machinery Manufacture and Reliability
- Vol. 55 (5) , 469-476
Providing Reliable Interference Fits of Rolling Bearings in Transfer Gearboxes
The off-road operation of machines requires for specialized training and equipment that makes it possible to provide its mobility even under challenging conditions with frequent overloading. In this regard, increased requirements are imposed on vehicle components, for which it is neccessary to provide precision in assembling thereof. One of the key components that makes it possible to transmits torque between the drive axles can be represented by a transfer gearbox, whose reliability determines the operability of the vehicle. In this paper, studies concerning the fit reliability of the L0/k6 rolling bearings in the GAZ transfer gearbox of the GAZ vehicle.
- 1 October 2025
- Published by Allerton Press in Russian Engineering Research
- Vol. 45 (10) , 1354-1359
Application of Digital Technologies to Achieve Maximum Wear Margin for Clearance Fits
The article proposes a method for assembling clearance fits using digital technologies to ensure the maximum wear margin, on the example of the camshaft
- 1 October 2025
- Published by Allerton Press in Russian Engineering Research
- Vol. 45 (10) , 1354-1359
Application of Digital Technologies to Achieve Maximum Wear Margin for Clearance Fits
The article proposes a method for assembling clearance fits using digital technologies to ensure the maximum wear margin, on the example of the camshaft
- 1 September 2025
- Published by Pleiades Publishing Ltd in Technical Physics Letters
- Vol. 51 (9) , 368-373
Optimizing the Camshaft Incoming Inspection by Simulation Modeling
As is known, during fault inspection, up to 35% of camshafts are rejected as unrepairable, of which 50% are because of cam wear (2/3) and bearing journal wear (1/3). The remaining defects are distributed relatively uniformly. Since this statistics has been collected on the basis of a large data set and may not correspond to a particular enterprise, it is impossible to build a universal model. Notations can graphically represent the process and provide its simulation modelling to identify vulnerabilities. A typical example of the notations is the BPMN. To increase the productivity of the camshaft fault inspection, two models in the BPMN notation have been constructed: the uniform distribution of the defect detection probability over operations and the nonuniform probability distribution according to the statistics. The simulation modelling of the fault inspection of 100 camshafts of a YaMZ-236 engine built in the BPMN notation has been carried out using the Business Studio software. In the real process, the parameters of 100 shafts have been controlled with universal and specialized measuring instruments under the conditions of an AB-Engineering specialized repair enterprise. The comparison of the real process with its model has yielded closer results at the nonuniform distribution, which has been taken into account during the optimization. The input inspection has been optimized based on the percentage of rejected products and the operation time. The time of the fault inspection after the optimization has been reduced by a factor of 1.35 and the discrepancy between the model and the real process data has been no more than 5%, which is indicative of the correctness of an approach used to model the processes characterized by a high degree of uncertainty.
- 1 September 2025
- Published by Pleiades Publishing Ltd in Technical Physics Letters
- Vol. 51 (9) , 368-373
Optimizing the Camshaft Incoming Inspection by Simulation Modeling
As is known, during fault inspection, up to 35% of camshafts are rejected as unrepairable, of which 50% are because of cam wear (2/3) and bearing journal wear (1/3). The remaining defects are distributed relatively uniformly. Since this statistics has been collected on the basis of a large data set and may not correspond to a particular enterprise, it is impossible to build a universal model. Notations can graphically represent the process and provide its simulation modelling to identify vulnerabilities. A typical example of the notations is the BPMN. To increase the productivity of the camshaft fault inspection, two models in the BPMN notation have been constructed: the uniform distribution of the defect detection probability over operations and the nonuniform probability distribution according to the statistics. The simulation modelling of the fault inspection of 100 camshafts of a YaMZ-236 engine built in the BPMN notation has been carried out using the Business Studio software. In the real process, the parameters of 100 shafts have been controlled with universal and specialized measuring instruments under the conditions of an AB-Engineering specialized repair enterprise. The comparison of the real process with its model has yielded closer results at the nonuniform distribution, which has been taken into account during the optimization. The input inspection has been optimized based on the percentage of rejected products and the operation time. The time of the fault inspection after the optimization has been reduced by a factor of 1.35 and the discrepancy between the model and the real process data has been no more than 5%, which is indicative of the correctness of an approach used to model the processes characterized by a high degree of uncertainty.
- 25 June 2025
- Published by Pleiades Publishing Ltd in Journal of Machinery Manufacture and Reliability
- Vol. 54 (3) , 306-311
Application of Digital Systems in Repair Enterprises
The peculiarities of repair enterprises, such as the irregularity of the work performed and its diversity, increase the workload of employees, who are usually not assigned to one operation and are more versatile specialists. The introduction of digital systems allows reducing the number of personnel errors, but the greatest effect can be achieved only by creating a single information environment. The use of the process approach will ensure the formation of a process register on the basis of which it is possible to organize traceability of parts, improve control and measurement procedures that will reduce the number of errors, and also allow analyzing the process based on the collected data. Such systems, united by a single information environment, help to predict post-repair indicators and bring the quality of repaired parts closer to new ones.
- 25 June 2025
- Published by Pleiades Publishing Ltd in Journal of Machinery Manufacture and Reliability
- Vol. 54 (3) , 306-311
Application of Digital Systems in Repair Enterprises
The peculiarities of repair enterprises, such as the irregularity of the work performed and its diversity, increase the workload of employees, who are usually not assigned to one operation and are more versatile specialists. The introduction of digital systems allows reducing the number of personnel errors, but the greatest effect can be achieved only by creating a single information environment. The use of the process approach will ensure the formation of a process register on the basis of which it is possible to organize traceability of parts, improve control and measurement procedures that will reduce the number of errors, and also allow analyzing the process based on the collected data. Such systems, united by a single information environment, help to predict post-repair indicators and bring the quality of repaired parts closer to new ones.
- Open Access
- 1 January 2025
- Published by Russian State Agrarian University - Moscow Timiryazev Agricultural Academy in Agricultural engineering
- Vol. 27 (3) , 81-89
Optimization of the incoming inspection of camshafts using simulation modeling
According to research, up to 35% of camshafts are rejected as unrepairable, of which 50% are due to wear of cams (2/3) and bearing journals (1/3). The remaining defects are distributed relatively evenly. These statistics are collected based on the processing of a large data set and may not correspond to a particular enterprise, so it is not possible to make a universal model. Notations can graphically represent the process and provide its simulation modelling to identify vulnerabilities. A typical example of notations of BPMN. In order to increase the productivity of the camshaft fault inspection, the authors have made two models in the BPMN notation: uniform distribution of probability of defect detection by operations and non-uniform distribution of probability, according to statistics. Simulation modelling of the fault inspection of 100 camshafts of the YaMZ-236 engine built in the BPMN notation was carried out in the Business Studio software. In the real process, the parameters of 100 shafts were controlled in the conditions of the specialized repair enterprise AB-Engineering by universal and specialized measuring instruments. After comparing the real process and its model, closer results were obtained with non-uniform distribution, which was taken into account during the optimization. The input inspection procedure was optimized based on the percentage of rejected products and the operation duration. The time spent on fault inspection after optimization was reduced in 1.35 times, the discrepancy between the model and the real process data did not exceed 5%, which indicates a correct approach to modelling processes associated with a high degree of uncertainty.
- 1 January 2025
- Published by Russian State Agrarian University - Moscow Timiryazev Agricultural Academy in Agricultural engineering
- Vol. 27 (3) , 81-89
Open AccessOptimization of the incoming inspection of camshafts using simulation modeling
According to research, up to 35% of camshafts are rejected as unrepairable, of which 50% are due to wear of cams (2/3) and bearing journals (1/3). The remaining defects are distributed relatively evenly. These statistics are collected based on the processing of a large data set and may not correspond to a particular enterprise, so it is not possible to make a universal model. Notations can graphically represent the process and provide its simulation modelling to identify vulnerabilities. A typical example of notations of BPMN. In order to increase the productivity of the camshaft fault inspection, the authors have made two models in the BPMN notation: uniform distribution of probability of defect detection by operations and non-uniform distribution of probability, according to statistics. Simulation modelling of the fault inspection of 100 camshafts of the YaMZ-236 engine built in the BPMN notation was carried out in the Business Studio software. In the real process, the parameters of 100 shafts were controlled in the conditions of the specialized repair enterprise AB-Engineering by universal and specialized measuring instruments. After comparing the real process and its model, closer results were obtained with non-uniform distribution, which was taken into account during the optimization. The input inspection procedure was optimized based on the percentage of rejected products and the operation duration. The time spent on fault inspection after optimization was reduced in 1.35 times, the discrepancy between the model and the real process data did not exceed 5%, which indicates a correct approach to modelling processes associated with a high degree of uncertainty.
- 1 January 2025
- Published by Pleiades Publishing Ltd in Technical Physics
- Vol. 70 (1) , 37-41
Increasing the Efficiency of Selective Assembly through the Use of Digital Technologies
The reliability and efficiency of equipment depend, among other things, on the operation of the cylinder–piston group (CPG)—the most frequently repaired unit in automotive and tractor engines. The quality of the CPG assembly is ensured by group interchangeability methods (selective assembly). In mechanical engineering, the human-readable marking of parts based on color schemes is insufficiently informative, so it is advisable to move from human-readable to machine-readable marking. In order to implement digital marking for spare parts and digital transformation of repair enterprises, the main quality indicators of CPG spare parts of engines and selective assembly of piston–liner joints of ZMZ-402 engines in 10 groups are considered. To improve the accuracy of the basic assembly conditions when implementing the method of intergroup interchangeability of CPG engines and automate the assembly process, it is proposed to use machine-readable marking based on a QR code or radio frequency tags. The advantages of a QR code are low cost of creation, fast readability of information, the ability to create a redundant QR code, high capacity, and the ability to read several tags simultaneously. Marking using radio frequency tags (RFID, NFC) allows encoding and reading information without direct contact. It is more resistant to mechanical impacts compared to a QR code. Significant disadvantages of radio frequency tags are the difficulty of reading when shielding the signal and the high cost of implementing this marking system. Digital marking of spare parts will help to forecast demand, improve automation, ease of use of warehouse databases and transparency of operations, and more accurately predict the timing and cost of repairs. Using a QR code together with the information environment (Internet catalog) of an enterprise will improve collection during selective assembly and reduce the likelihood of personnel errors.
- 1 January 2025
- Published by Pleiades Publishing Ltd in Technical Physics
- Vol. 70 (1) , 37-41
Increasing the Efficiency of Selective Assembly through the Use of Digital Technologies
The reliability and efficiency of equipment depend, among other things, on the operation of the cylinder–piston group (CPG)—the most frequently repaired unit in automotive and tractor engines. The quality of the CPG assembly is ensured by group interchangeability methods (selective assembly). In mechanical engineering, the human-readable marking of parts based on color schemes is insufficiently informative, so it is advisable to move from human-readable to machine-readable marking. In order to implement digital marking for spare parts and digital transformation of repair enterprises, the main quality indicators of CPG spare parts of engines and selective assembly of piston–liner joints of ZMZ-402 engines in 10 groups are considered. To improve the accuracy of the basic assembly conditions when implementing the method of intergroup interchangeability of CPG engines and automate the assembly process, it is proposed to use machine-readable marking based on a QR code or radio frequency tags. The advantages of a QR code are low cost of creation, fast readability of information, the ability to create a redundant QR code, high capacity, and the ability to read several tags simultaneously. Marking using radio frequency tags (RFID, NFC) allows encoding and reading information without direct contact. It is more resistant to mechanical impacts compared to a QR code. Significant disadvantages of radio frequency tags are the difficulty of reading when shielding the signal and the high cost of implementing this marking system. Digital marking of spare parts will help to forecast demand, improve automation, ease of use of warehouse databases and transparency of operations, and more accurately predict the timing and cost of repairs. Using a QR code together with the information environment (Internet catalog) of an enterprise will improve collection during selective assembly and reduce the likelihood of personnel errors.
- 25 November 2024
- Published by Pleiades Publishing Ltd in Journal of Machinery Manufacture and Reliability
- Vol. 53 (6) , 656-661
Improvement of the Decision-Making System for Fault Detection of Cylinder Liners
Repairing an internal combustion engine is a task that requires a high level of qualification from the employees of an organization, which leads to the need for using various tools to reduce the likelihood of errors. For enterprises with minimal implementation of digital technologies, a point-based evaluation system can be used to assess the feasibility of repairs. However, this method of evaluation is not convenient enough for enterprises with a more advanced digital environment, so a more successful solution for them would be to use software that also allows for an analysis of the economic costs of repairs, which will help reduce the influence of the human factor and increase the efficiency of the defect detection process.
- 25 November 2024
- Published by Pleiades Publishing Ltd in Journal of Machinery Manufacture and Reliability
- Vol. 53 (6) , 656-661
Improvement of the Decision-Making System for Fault Detection of Cylinder Liners
Repairing an internal combustion engine is a task that requires a high level of qualification from the employees of an organization, which leads to the need for using various tools to reduce the likelihood of errors. For enterprises with minimal implementation of digital technologies, a point-based evaluation system can be used to assess the feasibility of repairs. However, this method of evaluation is not convenient enough for enterprises with a more advanced digital environment, so a more successful solution for them would be to use software that also allows for an analysis of the economic costs of repairs, which will help reduce the influence of the human factor and increase the efficiency of the defect detection process.
- 27 May 2024
- Published by Pleiades Publishing Ltd in Journal of Machinery Manufacture and Reliability
- Vol. 53 (3) , 263-270
Digitalization of Fault Detection in Crankshafts
This article considers the application of digital technologies in repair agencies, considering several peculiarities, such as heterogeneous manufactured output, unsteady manufacturing as well as detailed checkout, application of the process-based approach together with automated control systems, automated preproduction engineering, equipment control and information collection, and enterprise management. The unified information environment formed by these systems reduces the number of incorrectly rejected and accepted parts by 75–80% and excludes wrong repair decisions and reduces the time needed for decision-making.
- 27 May 2024
- Published by Pleiades Publishing Ltd in Journal of Machinery Manufacture and Reliability
- Vol. 53 (3) , 263-270
Digitalization of Fault Detection in Crankshafts
This article considers the application of digital technologies in repair agencies, considering several peculiarities, such as heterogeneous manufactured output, unsteady manufacturing as well as detailed checkout, application of the process-based approach together with automated control systems, automated preproduction engineering, equipment control and information collection, and enterprise management. The unified information environment formed by these systems reduces the number of incorrectly rejected and accepted parts by 75–80% and excludes wrong repair decisions and reduces the time needed for decision-making.
- 1 January 2024
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 3033 (1) , 050002
Modern methods of selecting the process of restoring the operability of parts during the repair of machines
The article considers the main methods of choosing ways to restore parts during the repair of machines, analyzes them and reveals that the theoretical foundatio
- 1 January 2024
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 3033 (1) , 050002
Modern methods of selecting the process of restoring the operability of parts during the repair of machines
The article considers the main methods of choosing ways to restore parts during the repair of machines, analyzes them and reveals that the theoretical foundatio
- Open Access
- 1 March 2021
- Published by IOP Publishing in IOP Conference Series: Earth and Environmental Science
- Vol. 677 (5) , 052036
Processing modes influence on the sensory profile of various types of coffee
Technological modes of coffee beans processing are constantly developing and improving, which raise the quality of the second most consumed drink in the world after water and meeting an increasingly demand. This paper describes various processing modes and their effect on the organoleptic properties of the coffee drink. The interrelation of climatic features of the raw material growing region, coffee processing and roasting modes, and storage conditions makes it possible to obtain a product with an individual taste profile.
- 1 March 2021
- Published by IOP Publishing in IOP Conference Series: Earth and Environmental Science
- Vol. 677 (5) , 052036
Open AccessProcessing modes influence on the sensory profile of various types of coffee
Technological modes of coffee beans processing are constantly developing and improving, which raise the quality of the second most consumed drink in the world after water and meeting an increasingly demand. This paper describes various processing modes and their effect on the organoleptic properties of the coffee drink. The interrelation of climatic features of the raw material growing region, coffee processing and roasting modes, and storage conditions makes it possible to obtain a product with an individual taste profile.