Hui Pan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Hui Pan has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Zhenyu Liu
Chinese Academy of Sciences
3 shared publications - Eddie Wadbro
Department of Mathematics and Computer Science, Karlstad University, SE-651 88 Karlstad, Sweden
1 shared publication - Ge Gao
Changchun Institute of Optics, Fine Mechanics and Physics, Chinese Academy of Sciences, Changchun, China and University of Chinese Academy of Sciences, Beijing, China
1 shared publication Limin Chen
Changchun Institute of Optics, Fine Mechanics and Physics, Chinese Academy of Sciences, Changchun, China and University of Chinese Academy of Sciences, Beijing, China
1 shared publication- Limin Chen
Changchun Institute of Optics, Fine Mechanics and Physics (CIOMP), Chinese Academy of Science, Changchun 130033, Jilin, China
1 shared publication - Teng Zhou
School of Mechanical and Electrical Engineering, Hainan University, Haikou 570228, China
1 shared publication
Latest Publications
- Open Access
- 24 June 2020
- Published by MDPI AG in Micromachines
- Vol. 11 (6) , 613
Design Applicable 3D Microfluidic Functional Units Using 2D Topology Optimization with Length Scale Constraints
Due to the limits of computational time and computer memory, topology optimization problems involving fluidic flow frequently use simplified 2D models. Extruded versions of the 2D optimized results typically comprise the 3D designs to be fabricated. In practice, the depth of the fabricated flow channels is finite; the limited flow depth together with the no-slip condition potentially make the fluidic performance of the 3D model very different from that of the simplified 2D model. This discrepancy significantly limits the usefulness of performing topology optimization involving fluidic flow in 2D—at least if special care is not taken. Inspired by the electric circuit analogy method, we limit the widths of the microchannels in the 2D optimization process. To reduce the difference of fluidic performance between the 2D model and its 3D counterpart, we propose an applicable 2D optimization model, and ensure the manufacturability of the obtained layout, combinations of several morphology-mimicking filters impose maximum or minimum length scales on the solid phase or the fluidic phase. Two typical Lab-on-chip functional units, Tesla valve and fluidic channel splitter, are used to illustrate the validity of the proposed application of length scale control.
- 24 June 2020
- Published by MDPI AG in Micromachines
- Vol. 11 (6) , 613
Open AccessDesign Applicable 3D Microfluidic Functional Units Using 2D Topology Optimization with Length Scale Constraints
Due to the limits of computational time and computer memory, topology optimization problems involving fluidic flow frequently use simplified 2D models. Extruded versions of the 2D optimized results typically comprise the 3D designs to be fabricated. In practice, the depth of the fabricated flow channels is finite; the limited flow depth together with the no-slip condition potentially make the fluidic performance of the 3D model very different from that of the simplified 2D model. This discrepancy significantly limits the usefulness of performing topology optimization involving fluidic flow in 2D—at least if special care is not taken. Inspired by the electric circuit analogy method, we limit the widths of the microchannels in the 2D optimization process. To reduce the difference of fluidic performance between the 2D model and its 3D counterpart, we propose an applicable 2D optimization model, and ensure the manufacturability of the obtained layout, combinations of several morphology-mimicking filters impose maximum or minimum length scales on the solid phase or the fluidic phase. Two typical Lab-on-chip functional units, Tesla valve and fluidic channel splitter, are used to illustrate the validity of the proposed application of length scale control.
- 7 August 2017
- Published by Emerald Publishing in Engineering Computations
- Vol. 34 (6) , 2088-2104
An effective members-adding method for truss topology optimization based on principal stress trajectories
The purpose of this paper is to provide an effective members-adding method for truss topology optimization in plastic design. With the help of the distribution of principal stress trajectories, obtained by finite element analysis of the design domain, ineffective zones for force transmission paths can be found, namely, areas whose nodes may have ersatz nodal displacements. Members connected by these nodes are eliminated and the reduced ground structure is used for optimization. Adding members in short to long order and limiting the number of members properly with the most strained ones added, large-scale truss problems in one load case and multiple-load cases are optimized. Inefficient members (i.e. bars that fulfil the adding criterion but make no contribution to the optimal structure) added to the ground structure in each iterative step are reduced. Fewer members are used for optimization than before; therefore, faster solution convergence and less computation time are achieved with the optimized result unchanged. The proposed members-adding method in the paper can alleviate the phenomenon of ersatz nodal displacements, enhance computational efficiency and save calculating resources effectively.
- 7 August 2017
- Published by Emerald Publishing in Engineering Computations
- Vol. 34 (6) , 2088-2104
An effective members-adding method for truss topology optimization based on principal stress trajectories
The purpose of this paper is to provide an effective members-adding method for truss topology optimization in plastic design. With the help of the distribution of principal stress trajectories, obtained by finite element analysis of the design domain, ineffective zones for force transmission paths can be found, namely, areas whose nodes may have ersatz nodal displacements. Members connected by these nodes are eliminated and the reduced ground structure is used for optimization. Adding members in short to long order and limiting the number of members properly with the most strained ones added, large-scale truss problems in one load case and multiple-load cases are optimized. Inefficient members (i.e. bars that fulfil the adding criterion but make no contribution to the optimal structure) added to the ground structure in each iterative step are reduced. Fewer members are used for optimization than before; therefore, faster solution convergence and less computation time are achieved with the optimized result unchanged. The proposed members-adding method in the paper can alleviate the phenomenon of ersatz nodal displacements, enhance computational efficiency and save calculating resources effectively.
- Open Access
- 29 March 2017
- Published by MDPI AG in Micromachines
- Vol. 8 (4) , 105
A Novel Electroosmotic Micromixer with Asymmetric Lateral Structures and DC Electrode Arrays
We present a novel electroosmotic micromixer that consists of arrays of direct current (DC) asymmetric electrode and asymmetric lateral structures. By embedding asymmetric electrode arrays on the top and bottom walls of a rectangular microchannel appropriately, the flow perturbations and vortexes can be induced when a DC electric field is imposed. An efficient lateral structure is then sequentially combined with the rectangular microchannel, which enhances the mixing effect significantly. The effects of operational parameters such as the Reynolds number, the applied potential, and the Peclet number on the mixing performance are analyzed in detail by numerical simulations. The results indicate that an enhanced mixing performance can be achieved with low applied potential. The novel method proposed in this paper provides a simple solution for mixing in the field of micro-total-analysis systems.
- 29 March 2017
- Published by MDPI AG in Micromachines
- Vol. 8 (4) , 105
Open AccessA Novel Electroosmotic Micromixer with Asymmetric Lateral Structures and DC Electrode Arrays
We present a novel electroosmotic micromixer that consists of arrays of direct current (DC) asymmetric electrode and asymmetric lateral structures. By embedding asymmetric electrode arrays on the top and bottom walls of a rectangular microchannel appropriately, the flow perturbations and vortexes can be induced when a DC electric field is imposed. An efficient lateral structure is then sequentially combined with the rectangular microchannel, which enhances the mixing effect significantly. The effects of operational parameters such as the Reynolds number, the applied potential, and the Peclet number on the mixing performance are analyzed in detail by numerical simulations. The results indicate that an enhanced mixing performance can be achieved with low applied potential. The novel method proposed in this paper provides a simple solution for mixing in the field of micro-total-analysis systems.